Home › Audio / Visual / Telematics › AUDIO / VIDEO › INSTRUMENT PANEL SPEAKER › 2011.10–2016.05
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074071 INSTRUMENT PANEL SPEAKER G

AUDIO / VIDEO  INSTRUMENT PANEL SPEAKER  INSPECTION  


PROCEDURE

Hide 86160P 1.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY (for 6 Speakers)

a.

With the speaker installed, check that there is no looseness or other abnormalities.


b.

Check that there is no foreign matter in the speaker, no tears on the speaker cone or other abnormalities.


c.
E226097
2,1.646 2.24,0.948 2.24,0.948 2.354,0.948 false 1.24,2.323 1.417,1.813 false 2.417,2.323 2.24,1.813 false 1.698,1.646 2.021,0.698 2.021,0.698 2.146,0.698 false 0.094,0.083 0.25,0.229 0.156,0.146 10 false *a 2.177,0.604 2.333,0.75 0.156,0.146 10 false + 0.927,2.344 1.5,2.49 0.573,0.146 10 false TWR+*A 0.927,2.5 1.5,2.646 0.573,0.146 10 false TWL+*B 2.396,0.875 2.969,1.021 0.573,0.146 10 false TWR-*A 2.396,1.042 2.969,1.188 0.573,0.146 10 false TWL-*B 2.406,2.344 2.521,2.49 0.115,0.146 10 false -
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Measure the resistance of the speaker.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (TWR-) - 4 (TWR+) Always 10 kΩ or higher
1 (-) - 2 (TWR-) Always Below 1 Ω
3 (+) - 4 (TWR+) Always Below 1 Ω
2 (TWL-) - 4 (TWL+) Always 10 kΩ or higher
1 (-) - 2 (TWL-) Always Below 1 Ω
3 (+) - 4 (TWL+) Always Below 1 Ω


If the result is not as specified, replace the speaker.


d.

When there is a possibility that either the right or left speaker is malfunctioning, interchange the speakers and perform an inspection. If the malfunction disappears after interchanging the speakers, replace the malfunctioning speaker.

HINT:

Connect all connectors to the speakers when performing an inspection. If the result is not as specified, replace the speaker.



Hide 86160P 2.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY (for 10 Speakers)

a.

With the speaker installed, check that there is no looseness or other abnormalities.


b.

Check that there is no foreign matter in the speaker, no tears on the speaker cone or other abnormalities.


c.
E219304
0.094,0.063 0.281,0.229 0.188,0.167 10 false *a
*a Component without harness connected
(Front No. 2 Speaker Assembly)


Measure the resistance of the speaker.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Always 3.4 to 5.2 Ω


If the result is not as specified, replace the speaker.


Hide 86160J 3.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)

a.

With the speaker installed, check that there is no looseness or other abnormalities.


b.

Check that there is no foreign matter in the speaker, no tears on the speaker cone or other abnormalities.


c.
E222247C21
0.095,0.047 0.279,0.222 0.185,0.175 10 *a
*a Component without harness connected
(Front No. 3 Speaker Assembly)


Measure the resistance of the speaker.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 6.8 to 10.2 Ω


If the result is not as specified, replace the speaker.