Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074081 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E226165E14
1.0,0.775 1.797,0.956 0.796,0.181 10 from Battery 0.342,1.575 1.791,1.755 1.449,0.181 10 from ACC NO. 1 Relay 0.408,2.396 1.792,2.576 1.383,0.181 10 from IG1 NO. 2 Relay 3.17,2.606 4.197,2.787 1.027,0.181 10 ECU-IG1 NO. 2 3.371,1.023 4.009,1.203 0.638,0.181 10 RADIO-B 3.35,1.809 4.02,1.99 0.67,0.181 10 ECU-ACC 5.551,2.984 5.754,3.151 0.203,0.167 10 7 5.551,1.377 5.754,1.544 0.203,0.167 10 3 5.431,0.781 5.741,0.948 0.31,0.167 10 I152 5.431,1.579 5.741,1.746 0.31,0.167 10 I152 5.431,2.379 5.73,2.546 0.299,0.167 10 I155 5.431,3.168 5.737,3.335 0.306,0.167 10 I152 5.814,0.781 6.109,0.948 0.295,0.167 10 +B1 5.814,1.579 6.25,1.746 0.436,0.167 10 ACC1 5.814,2.379 5.99,2.546 0.176,0.167 10 IG 5.814,3.168 6.251,3.335 0.437,0.167 10 GND1 5.281,3.624 7.031,3.953 1.749,0.329 10 Radio and Display Receiver Assembly 5.547,0.583 5.676,0.75 0.129,0.167 10 4 5.547,2.167 5.676,2.334 0.129,0.167 10 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY, BODY GROUND)
a.

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below .

Standard Resistance:
Tester Connection Condition Specified Condition
I152-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I152-4 (+B1) - I152-7 (GND1) Always 11 to 14 V
I152-3 (ACC1) - I152-7 (GND1) Ignition switch ACC 11 to 14 V
I155-1 (IG) - I152-7 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR