Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014599 AUDIO / VIDEO _0074081 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  OPERATION CHECK  


CHECK PANEL & STEERING SWITCH


HINT:
·

The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Panel & Steering Switch.


c.
E225786N05
2.25,1.438 3.063,1.438 false 0.323,1.156 1.021,1.156 false 2.854,1.083 3.052,1.083 false 0.146,1.073 0.302,1.229 0.156,0.156 10 false *a 3.083,1 3.24,1.156 0.156,0.156 10 false *b 3.083,1.354 3.24,1.51 0.156,0.156 10 false *c

Panel & Steering Switch Check Mode

Screen Description
Display Content
*a: Switch condition "Pushed" is displayed when any switch is pushed
*b: Number of switches pushed
·

Number of switches pushed at once is displayed

·

If more than 3 switches are pushed at once, "More than 3" is displayed


*c: Rotary switch direction Direction of rotary switch is displayed

i.

Operate each switch and check that the switch conditions are correctly displayed.

NOTICE:

When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.





CHECK TOUCH SWITCH


HINT:
·

The touch switches on the screen are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Touch Switch.


c.
E176521

Touch Switch Check

i.

Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT:
·

A "+" mark is displayed where the display is touched.

·

The "+" mark remains on the display even after the finger is removed.






CHECK MICROPHONE & VOICE RECOGNITION


HINT:
·

The microphone and microphone input level are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Microphone Check.


c.
E225853N03
3.164,0.784 3.32,0.941 0.156,0.157 10 *a 3.135,0.875 2.82,0.875 false

Microphone & Voice Recognition Check

Screen Description
Display Content
*a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

i.

When speaking into the microphone, check that the microphone input level meter changes according to the input level.

HINT:

The microphone is active at all times when this screen is displayed.





CHECK COLOR BAR (for RHD before Oct. 2014, for LHD)


HINT:
·

The display color on the screen is checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Color Bar.


c.
E226305

Color Bar Check Mode

i.

Select a color bar from the "Color Bar Check Mode" screen.


ii.

Check the display color.

HINT:
·

The entire screen turns to the color or stripe selected.

·

Touching the display will return to the "Color Bar Check Mode" screen.






CHECK VEHICLE SIGNAL


HINT:
·

Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.

Enter the following menus: Function Check/Setting > Vehicle Signal.


c.
E225776

Vehicle Signal Check Mode

Screen Description
Display Content
Battery Battery voltage is displayed.
IG Ignition switch ON/OFF state is displayed.
PKB Parking brake ON/OFF state is displayed.
REV Reverse signal ON/OFF state is displayed.
SPEED Vehicle speed is displayed in km/h.
TAIL Tail signal (Light control switch) ON/OFF state is displayed.
ADIM/TCAN Brightness state DIM (with) / BRIGHT (without) is displayed.

HINT:
·

Only items sending vehicle signals will be displayed.

·

This screen displays vehicle signals input to the radio and display receiver assembly.

·

This screen is updated once per second when vehicle input signals change.



i.

When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.




CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING (for RHD before Oct. 2014, for LHD)


HINT:
·

The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E226134

Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.


d.
E225788N04
0.117,0.653 0.272,0.807 0.155,0.154 10 *a 0.325,0.738 0.582,0.738 false 0.117,0.911 0.272,1.065 0.155,0.154 10 *b 0.325,0.996 0.582,0.996 false

Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)

Screen Description
Display Content
*a: Receive voice level adjustment Setting for the voice level received from "Bluetooth" compatible phones.
*b: Send voice level adjustment Setting for the voice level sent from "Bluetooth" compatible phones.

NOTICE:

Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the received voice or sent voice quality is still acceptable after changing this setting.


i.

If the voice level is low, press the up button, and if the voice level is loud, press the down button.

HINT:
·

Each voice level setting is reflected when going back to the normal mode.

·

The voice level adjustment ranges from -5 to +5.

·

The initial level is "0".





e.
E228924C07
2.865,1.021 3.115,1.021 false 2.833,1.552 3.104,1.552 false 1.802,1.635 1.802,1.906 false 3.156,0.948 3.323,1.104 0.167,0.156 10 false *a 3.146,1.469 3.313,1.625 0.167,0.156 10 false *b 1.698,1.927 1.865,2.083 0.167,0.156 10 false *c
*a Numeric keypad
*b Setting button
*c Reset button


Hands-Free Voice Quality Setting (Voice Quality Type adjustment)

i.

If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.


ii.

When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

Setting
Parameter Target Phenomenon Voice Quality Type (FUJITSU TEN) Voice Quality Type (Panasonic) Voice Quality Type (Pioneer) Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
Echo The other party hears a lot of echo when speaking to you. 1000
2000
0001 0001
0002
0003
0004
0005
The amount of echo the other party hears of their own voice is reduced. When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc.
Half Duplex When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc. 0100
0200
0002 0010
0020
0030
0040
0050
When both parties speak at the same time, the phenomenon by which the other party's voice suddenly drops in volume, cuts out etc. reduces. The amount of echo the other party hears of their own voice increases.
Noise The other party hears a lot of vehicle noise etc. when listening to your voice. 0010
0020
0004 0100
0200
0300
0400
0500
The amount of vehicle noise etc. the other party hears when listening to your voice reduces. The quality of your voice, that the other party hears, reduces.
Voice Quality The quality of your voice, that the other party hears, is low. 0001
0002
0003 1000
2000
3000
4000
5000
The quality of your voice, that the other party hears, increases. The amount of noise etc. the other party hears when listening to your voice increases.

HINT:
·

Refer to the "Unit Version Information" screen to confirm radio and display receiver assembly manufacturer information.

·

The type of adjustments that can be made using voice quality type adjustment only adjust the sound quality of your voice that the other party hears. It cannot adjust the sound quality of the other party's voice that you hear.

·

The default value is "0000".

·

Settings will be applied when the normal screen is returned to.

·

When multiple setting values are available, the higher the setting value, the bigger the effect. However, as the positive effects increase, so do the negative effects.

·

If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

·

If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.






CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING (for RHD from Oct. 2014)


HINT:
·

The hands-free voice quality of a "Bluetooth" compatible phone can be adjusted using the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



a.

Enter diagnostic mode.

Click here xxx


b.

Enter the following menus: Function Check/Setting > HF Voice Quality Setting.


c.
E268475C01
1.792,1.854 1.792,1.646 false 3.01,1.021 2.875,1.021 false 3.01,1.542 2.854,1.542 false 3.042,0.927 3.26,1.146 0.219,0.219 10 false *a 3.042,1.469 3.26,1.688 0.219,0.219 10 false *b 1.719,1.854 1.938,2.073 0.219,0.219 10 false *c
*a Numeric Keypad
*b Setting Button
*c Reset Button


Hands-Free Voice Quality Setting

i.

If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.


ii.

When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

Settings
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A
(Noise)
The other party hears background noise when listening to your voice. 1000 The amount of background noise the other party hears when listening to your voice is reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.
B
(Noise)
The other party hears a lot of background noise when listening to your voice. 2000 The amount of background noise the other party hears when listening to your voice is sharply reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.
C
(Echo)
The other party hears weak echoes. 0100 The amount of echo is reduced (low level). Sound quality of the other party deteriorates (low level).
D
(Echo)
The other party hears strong echoes. 0200 The amount of echo is reduced (high level). Sound quality of the other party deteriorates (high level).

Settings (When Multiple Phenomenon Occurred)
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A+C The other party hears background noise and weak echoes when listening to your voice. 1100
·

The amount of background noise the other party hears when listening to your voice is reduced.

·

The amount of echo is reduced (low level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (low level).


A+D The other party hears background noise and strong echoes when listening to your voice. 1200
·

The amount of background noise the other party hears when listening to your voice is reduced.

·

The amount of echo is reduced (high level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (high level).


B+C The other party hears a lot of background noise and weak echoes when listening to your voice. 2100
·

The amount of background noise the other party hears when listening to your voice is sharply reduced.

·

The amount of echo is reduced (low level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (low level).


B+D The other party hears a lot of background noise and strong echoes when listening to your voice. 2200
·

The amount of background noise the other party hears when listening to your voice is sharply reduced.

·

The amount of echo is reduced (high level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (high level).



HINT:
·

The default value is "0000".

·

Settings will be applied when the setting button is selected.

·

If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

·

If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.






CHECK SPEAKER (for RHD from Oct. 2014)


HINT:
·

This function is used when checking the speaker wiring and whether the speakers are functioning properly.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



a.

Turn audio mode on and play any audio source.

HINT:

This audio source will be used for the speaker check.



b.

Enter diagnostic mode.

Click here xxx


c.

Enter the following menus: Failure Diagnosis > System Check.


d.
E268474

Select "SP Check ON" on the "System Check Mode" screen.


e.

Check the speaker wiring and check that the speakers are functioning properly.

HINT:
·

Check that each speaker outputs sound from the selected audio source properly.

·

"SP Check OFF" is displayed during the speaker check.

·

Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.

·

More than one speaker may sound simultaneously depending on the speaker wiring.




f.

Sound stops when any of the following conditions are met:

i.

"SP Check OFF" switch is selected.


ii.

The ignition switch is turned off.


iii.

Diagnostic mode is turned off.


iv.

The screen is changed to another screen.


v.

Audio mode is turned off.




CHECK SOFTWARE ERROR HISTORY


HINT:

This function is used to check the cause when the radio and display receiver assembly screen is blacked out.


a.

Check Software Error History.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body / Navigation System/ Utility / Software Error History.

Body Electrical > Navigation System > Utility
Tester Display
Software Error History
50005 212 4150

v.

When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.

Software Error History Screen Description
Error Description Trigger Detail
Software Reset Navi Microcomputer Hexadecimal Number
Audio Microcomputer
CAN Microcomputer
No Video Signal Front Monitor
Rear Monitor
MOST Cold Restart Always

HINT:
·

Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the intelligent tester occurs, a "-" is displayed for the display items.





b.

Clear software error history.

i.

When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR).

·

Cleared using the intelligent tester.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





CHECK OPTICAL DISC ERROR HISTORY


HINT:

This function is used to check the cause of an optical disc error.


a.

Check optical disc error history.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body / Navigation System/ Utility / Optical Disc Error History.

Body Electrical > Navigation System > Utility
Tester Display
Optical Disc Error History
50005 212 4151

v.

When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

Optical Disc Error History Screen Description
Display Content
Error Type Displays the type of error.
Device Displays the malfunctioning device.
Date Displays the date and time that the malfunction occurred.

"Error Type" Screen Description
Error Type Detection Condition Action
Read Error When a disc read error occurs. Proceed to next suspected area shown in Problem Symptoms Table (See page (Click here))
Disc damaged/upside down/dirty When it is determined that any of the following is the cause of the disc read error:
·

The disc cannot be read.

·

The disc cannot be read because of dirt or scratches.

·

The disc cannot be read because it is inserted upside down.


Cannot determine disc type An unsuitable disc is inserted.
DPS error When an error occurs while decoding MP3/WMA/AAC files.
Some files are corrupt
·

When MP3/WMA/AAC files cannot be played back because they are unsupported.

·

Even though the file extensions are MP3, WMA or AAC files cannot be played back because the header information cannot be read.


Some files cannot be found
·

When a disc without music data is played back.

·

When there are no playable MP3/WMA/AAC files.


Copy protection violation When a file with copyright protection that cannot be played back is played back.

"Device" Screen Description
Device Component
DVD-P Not available
CD-P Radio and display receiver assembly
R-Seat DVD-P Not available

HINT:
·

Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the intelligent tester occurs, a "-" or blank is displayed for the display items.





b.

Clear optical disc error history.

i.

When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR).

·

Cleared using the intelligent tester.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





CHECK VIDEO DEVICE CONNECTION CHECK (for RHD from Oct. 2014)


HINT:
·

This function is used to detect disconnection of the video devices.

·

In order to inspect the RSE, a disc should be inserted into the radio and display receiver assembly.



a.

Check Video Device Connection Check.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.


v.

When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.

HINT:
·

DTCs are stored when errors are detected.

·

Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.



Video Device Connection Check Screen Description
Error Detected Image Line (Type) Areas to be Checked
H/U - > Separate Display (GVIF) Not available
H/U - > Full RSE (GVIF) Not available
RSE - > Seat Back Display RH (GVIF) Not available
RSE - > Seat Back Display LH (GVIF) Not available
Rear Camera - > H/U (NTSC) NTSC video signal between the radio and display receiver assembly and rear television camera assembly
IPA/BGM/PVM ECU - > Separate Display (GVIF) Not available
IPA/BGM/PVM ECU - > H/U (NTSC) Not available
IPA/BGM/PVM ECU - > H/U (GVIF) Not available



b.

Clear video device connection check.

i.

Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.

Click here xxx

·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.