Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2011.10–2014.05
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0074086 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E230186E01
0.46,1.382 1.583,1.534 1.123,0.151 10 Skid Control ECU 0.867,0.583 1.158,0.734 0.292,0.151 10 SP1 0.153,1.382 0.472,1.564 0.319,0.181 10 A49 1.207,0.583 1.394,0.731 0.187,0.148 10 2 0.119,2.737 3.204,2.901 3.085,0.164 10 Certification ECU (Smart Key ECU Assembly)*5 0.119,2.584 0.41,2.748 0.291,0.164 10 I78 0.063,7.472 0.328,7.636 0.266,0.164 10 I72 0.374,7.472 2.686,7.79 2.313,0.319 10 Windshield Wiper Relay Assembly*4 1.687,7.081 2.101,7.236 0.414,0.155 10 SPD 1.637,2.338 2.038,2.492 0.401,0.155 10 SPD 2.108,2.334 2.288,2.493 0.18,0.159 10 27 2.931,2.334 3.11,2.493 0.18,0.159 10 21 3.941,2.334 4.121,2.493 0.18,0.159 10 18 2.931,3.747 3.11,3.906 0.18,0.159 10 19 3.941,3.747 4.121,3.906 0.18,0.159 10 17 2.087,7.081 2.271,7.24 0.184,0.159 10 24 3.953,7.102 4.136,7.261 0.184,0.159 10 16 2.934,7.102 3.118,7.261 0.184,0.159 10 20 5.345,7.103 5.549,7.265 0.204,0.162 10 57 5.296,5.108 5.513,5.27 0.217,0.162 10 17 5.419,0.564 5.723,0.714 0.304,0.15 10 8 5.419,2.348 5.695,2.498 0.276,0.15 10 9 5.589,0.662 5.788,0.812 0.199,0.15 10 SI 5.583,2.446 5.784,2.597 0.201,0.151 10 +S 5.009,2.779 5.341,2.925 0.332,0.146 10 I18 5.285,2.779 7.12,2.972 1.836,0.193 10 Combination Meter Assembly 5.781,7.479 6.058,7.632 0.277,0.153 10 A25 6.102,7.479 6.513,7.655 0.411,0.176 10 ECM 4.409,5.633 6.988,5.999 2.58,0.366 10 Navigation ECU Sub-assembly*2 or Radio and Display Receiver Assembly*3 2.353,8.235 4.748,8.398 2.395,0.163 10 *5: w/ Smart Entry and Start System 0.317,8.235 1.993,8.395 1.676,0.16 10 *4: w/ Auto Wiper System 4.808,7.912 6.716,8.094 1.907,0.182 10 *3: for Radio and Display Type 5.662,7.092 5.991,7.238 0.329,0.145 10 SPD 5.588,5.201 5.917,5.347 0.329,0.145 10 SPD 5.588,3.771 5.917,3.917 0.329,0.145 10 SPD 5.256,5.286 5.575,5.432 0.319,0.146 10 I155 5.307,5.473 5.497,5.619 0.19,0.146 10 *3 4.939,5.108 5.155,5.27 0.217,0.162 10 17 4.927,5.286 5.202,5.432 0.276,0.146 10 I67 4.944,5.473 5.129,5.619 0.185,0.146 10 *2 2.111,3.76 2.423,3.922 0.312,0.162 10 11 0.595,4.162 0.87,4.316 0.275,0.153 10 I69 5.326,3.771 5.638,3.933 0.312,0.162 10 17 4.99,4.144 5.53,4.304 0.54,0.16 10 I150 0.903,4.162 2.405,4.526 1.501,0.364 10 Stereo Component Amplifier Assembly*2 5.328,4.144 7.082,4.321 1.754,0.176 10 Radio Receiver Assembly*1 1.712,3.773 2.04,3.918 0.329,0.145 10 SPD 2.438,7.912 4.475,8.094 2.037,0.182 10 *2: for Navigation Receiver Type 0.317,7.912 2.107,8.082 1.79,0.169 10 *1: for Radio Receiver Type 3.094,7.472 4.314,7.634 1.22,0.162 10 Junction Connector 2.782,7.472 3.183,7.636 0.401,0.164 10 I124

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E263768C02
1.521,0.448 1.885,0.688 0.365,0.24 0.958,2.104 1.365,1.521 false 0.146,0.125 0.458,0.323 0.313,0.198 10 *a 1.615,0.49 1.948,0.688 0.333,0.198 10 I18 1.094,4.063 1.615,4.281 0.521,0.219 10 (A) 0.844,2.135 1.177,2.333 0.333,0.198 10 +S 2.792,3.719 3.313,3.938 0.521,0.219 10 GND
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal I18-9 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I18-9 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the stereo component amplifier assembly connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I69-11 (SPD) - I18-9 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the stereo component amplifier assembly connector.


b.

Disconnect the junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I69-11 (SPD) - I124-19 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)