Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0074086 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

The navigation ECU sub-assembly sends a sound signal to the stereo component amplifier assembly via the sound signal circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E230080E03
1.063,1 1.344,1.26 0.281,0.26 10 false L- 1.052,1.479 1.438,1.76 0.385,0.281 10 false L+ 1.052,1.948 1.479,2.219 0.427,0.271 10 false R- 1.042,2.417 1.385,2.677 0.344,0.26 10 false R+ 1.323,0.885 1.51,1.052 0.188,0.167 10 false 2 1.323,1.344 1.51,1.51 0.188,0.167 10 false 3 1.323,1.833 1.51,2 0.188,0.167 10 false 4 1.323,2.313 1.51,2.479 0.188,0.167 10 false 5 5.74,0.875 5.854,1.042 0.115,0.167 10 false 6 5.74,1.365 5.844,1.531 0.104,0.167 10 false 2 5.74,2.313 5.844,2.479 0.104,0.167 10 false 1 5.74,1.823 5.854,1.99 0.115,0.167 10 false 5 5.927,0.969 6.26,1.125 0.333,0.156 10 false FL- 5.927,1.448 6.26,1.604 0.333,0.156 10 false FL+ 5.927,1.948 6.26,2.104 0.333,0.156 10 false FR- 5.927,2.427 6.26,2.583 0.333,0.156 10 false FR+ 5.76,2.854 6.083,3.031 0.323,0.177 10 false I64 0.26,2.813 0.563,2.979 0.302,0.167 10 false I69 0.26,2.979 1.458,3.385 1.198,0.406 10 false Stereo Component Amplifier Assembly 3.25,2.698 4.063,2.948 0.813,0.25 10 false (Shielded) 0.938,0.51 1.281,0.667 0.344,0.156 10 false SLD 1.333,0.396 1.521,0.563 0.188,0.167 10 false 6 5.76,3.021 6.792,3.427 1.031,0.406 10 false Navigation ECU Sub-assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the navigation ECU sub-assembly connector.


b.

Disconnect the stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I69-5 (R+) - I64-1 (FR+) Always Below 1 Ω
I69-4 (R-) - I64-5 (FR-) Always Below 1 Ω
I69-3 (L+) - I64-2 (FL+) Always Below 1 Ω
I69-2 (L-) - I64-6 (FL-) Always Below 1 Ω
I69-6 (SLD) - Body ground Always 10 kΩ or higher
I69-5 (R+) - Body ground Always 10 kΩ or higher
I69-4 (R-) - Body ground Always 10 kΩ or higher
I69-3 (L+) - Body ground Always 10 kΩ or higher
I69-2 (L-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR