Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014600 NAVIGATION / MULTI INFO DISPLAY _0074086 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Data Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal from a USB device to the navigation ECU sub-assembly via this circuit.

WIRING DIAGRAM

E229860E99
3.26,2.333 4.25,2.74 0.99,0.406 10 false (Shielded) 0.875,0.625 1.49,0.969 0.615,0.344 10 false UDO- 0.854,1.438 1.521,1.719 0.667,0.281 10 false UDO+ 0.865,2.219 1.469,2.51 0.604,0.292 10 false UJSS 5.729,1.271 5.906,1.427 0.177,0.156 10 false 3 5.729,0.469 5.906,0.625 0.177,0.156 10 false 2 5.729,2.052 5.906,2.208 0.177,0.156 10 false 5 1.323,0.49 1.5,0.646 0.177,0.156 10 false 2 1.323,1.271 1.5,1.427 0.177,0.156 10 false 3 1.323,2.052 1.5,2.208 0.177,0.156 10 false 5 0.344,2.635 0.875,2.885 0.531,0.25 10 false I146 5.75,2.646 6.219,2.917 0.469,0.271 10 false I147 0.333,2.792 1.531,3.188 1.198,0.396 10 false No. 1 Stereo Jack Adapter Assembly 5.75,2.813 6.771,3.156 1.021,0.344 10 false Navigation ECU Sub-assembly 5.927,0.646 6.354,0.802 0.427,0.156 10 false US1- 5.927,1.458 6.563,1.969 0.635,0.51 10 false US1+ 5.927,2.24 6.354,2.396 0.427,0.156 10 false USG1

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.
E226480C54
1.458,2.271 1.896,2.563 0.438,0.292 1.49,0.219 1.927,0.51 0.438,0.292 1.583,1.427 1.115,1.594 false 2.333,1.594 1.865,1.427 false 1.615,3.448 1,3.844 false 1.833,3.448 2.448,3.688 false 1.781,3.542 2.448,3.979 false 1.781,1.552 2.281,1.927 false 0.177,2.25 0.583,2.604 0.406,0.354 10 false *b 1.552,2.333 2,2.719 0.448,0.385 10 false I146 0.521,3.771 0.917,3.927 0.396,0.156 10 false UDO- 0.177,0.219 0.542,0.656 0.365,0.438 10 false *a 1.594,0.281 2.115,0.646 0.521,0.365 10 false I147 0.646,1.51 1.229,1.76 0.583,0.25 10 false US1+ 2.354,1.51 2.865,1.771 0.51,0.26 10 false US1- 2.469,3.615 2.885,3.771 0.417,0.156 10 false UDO+ 2.469,3.917 2.865,4.073 0.396,0.156 10 false UJSS 2.313,1.865 3.01,2.25 0.698,0.385 10 false USG1
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Disconnect the navigation ECU sub-assembly connector.


b.

Disconnect the No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I147-2 (US1-) - I146-2 (UDO-) Always Below 1 Ω
I147-3 (US1+) - I146-3 (UDO+) Always Below 1 Ω
I147-5 (USG1) - I146-5 (UJSS) Always Below 1 Ω
I147-2 (US1-) - Body ground Always 10 kΩ or higher
I147-3 (US1+) - Body ground Always 10 kΩ or higher
I147-5 (USG1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR