Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  SYSTEM DESCRIPTION  


GENERAL


·

The blind spot monitor is a system that assists the driver in making the decision to change lanes. The system uses quasi-millimeter wave radar to detect vehicles that are traveling in an adjacent lane in the area that is not reflected in the outer rear view mirror assembly. The system advises the driver of the existence of a vehicle by illuminating the blind spot monitor indicator on the outer rear view mirror assembly.

·

If the turn signal is operated while the blind spot monitor indicator on an outer rear view mirror assembly is illuminated, the indicator starts blinking to give additional warning to the driver.



FUNCTION OF COMPONENTS


Component Function
Blind Spot Monitor Sensor
·

Consists of a 24 GHz radar module and an integrated processing module.

·

Illuminates the outer rear view mirror indicator on the outer rear view mirror assembly when a vehicle is present in the blind spot area.

·

Changes the outer rear view mirror indicator on the outer rear view mirror assembly from illuminated to blinking when a turn signal is received from the combination meter assembly.


Outer Rear View Mirror Indicator Turns on or blinks the indicator based on a signal from the blind spot monitor sensor.
Outer Mirror Control Computer Assembly Receives a signal from the blind spot monitor sensor and sends the signal to the outer rear view mirror indicator.
Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly) Turns the blind spot monitor on or off.
Combination Meter Assembly
·

Sends a turn signal state signal from the headlight dimmer switch assembly (turn signal light switch) to the blind spot monitor sensor via CAN communication.

·

If the blind spot monitor detects a malfunction while it is operating, it turns on a warning light.


Main Body ECU
(Multiplex Network Body ECU)
Sends the destination information to the blind spot monitor senor via CAN communication.
Brake Actuator Assembly
(Skid Control ECU)
Transmits a vehicle speed signal to the blind spot monitor sensor via CAN Communication.
ECM Sends shift position signal (R) and HV flag to the blind spot monitor sensor via CAN communication.
Steering Sensor Detects the angle of the steering wheel and sends the resulting signals to the blind spot monitor sensor via CAN communication.


OPERATION DESCRIPTION


a.

Operation conditions of the blind spot monitor system

·

The blind spot monitor main switch (warning canceling switch assembly) is on.

·

Vehicle speed is more than approximately 40 km/h (25 mph).



b.

Conditions in which a sensor can detect a vehicle

The blind spot monitor system indicates detection of a vehicle in the detection area when either condition is met:

i.

When a vehicle is detected in an adjacent lane overtaking this vehicle.


ii.

When another vehicle is detected entering the detection area because it changed lanes.



c.
E263938
2.688,0.792 3.052,1.094 0.365,0.302 10 false *a 1.083,4.385 1.458,4.667 0.375,0.281 10 false *b 1.927,4.375 2.313,4.667 0.385,0.292 10 false *c
*a Within approx. 3.5 m (11.49 ft) from the side of the vehicle
*b Within approx. 3 m (9.85 ft) behind the rear bumper
*c Within approx. 1 m (3.29 ft) forward of the rear bumper


Detection area

i.

Vehicles in the following areas can be detected:




OPERATION OF OUTER REAR VIEW MIRROR INDICATOR ON OUTER REAR VIEW MIRROR ASSEMBLY


a.

The outer rear view mirror indicator on each outer rear view mirror assembly operates as follows:

E263939
1.208,0.042 3.208,0.344 2,0.302 10 Outer rear view mirror indicator 1.271,0.375 1.729,0.573 0.458,0.198 10 LH: 1.26,1.542 1.719,1.74 0.458,0.198 10 RH: 4.052,0.083 5.198,0.344 1.146,0.26 10 Blinking speed 4.135,1.313 4.594,1.51 0.458,0.198 10 ON 4.073,1.927 4.531,2.125 0.458,0.198 10 OFF 4.938,0.917 5.698,1.292 0.76,0.375 10 0.125 s 5.427,0.927 6.24,1.375 0.813,0.448 10 0.125 s

·

When the blind spot monitor main switch (warning canceling switch assembly) is turned on, the outer rear view mirror indicator on each outer rear view mirror assembly illuminates for 3 seconds (initial check).

·

While the system is operating, when a sensor detects a vehicle in the blind spot area, the outer rear view mirror indicator on the outer rear view mirror assembly illuminates.

·

While the system is detecting a vehicle in the detection area and the indicator is illuminated, if the turn signal is turned on, the indicator starts blinking.