PARKING ASSIST MONITOR DIAGNOSIS SYSTEM
For parking assist monitor system diagnosis, signals received by the navigation ECU sub-assembly can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the navigation ECU sub-assembly.
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>CALIBRATION).
The displayed items may differ depending on vehicle specifications.
DIAGNOSIS SCREEN TRANSITION (during parking assist monitor system initialization)
DIAGNOSIS SCREEN TRANSITION (after parking assist monitor system initialization)
VEHICLE SIGNAL CHECK
Start diagnostic mode (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR).
Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting " screen.
Select "Vehicle Signal" on the "Function Check/Setting " screen.
Vehicle Signal Check Mode
When the "Vehicle Signal Check Mode" screen is displayed, check "REV" the vehicle signal conditions.
Only conditions having inputs are displayed.
This screen displays vehicle signals input to the navigation ECU sub-assembly.
For details of this function, refer to Diagnosis Display Detailed Description in System Description (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>SYSTEM DESCRIPTION)
Finish diagnostic mode (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR).
CAR SIGNAL CHECK (parking assist monitor system input signals)
Start diagnostic mode (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR).
Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting " screen.
Select "Camera Setting" on the "Function Check/Setting " screen.
Select "Next" on the "Car Information Check " screen.
After "Next" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the navigation ECU sub-assembly was replaced.
| Parking Assist Monitor System Initialization | Screen Transition |
|---|---|
| Not performed | Car Signal Check screen |
| Performed | Mode Setting screen |
When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Car Signal Check" screen.
To select a grayed out item, select and hold the item for 2 seconds or more.
Car Signal Check
On the "Car Signal Check" screen, it is possible to inspect the state of signals and check the settings.
| Item | Inspection Detail | Note |
|---|---|---|
| BCTY | Luggage compartment door courtesy light switch signal input | When "CHK" (red) is displayed, selecting "Next" will not change to the next screen. |
When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.
If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".
BCTY inspection
If "CHK" (red) is displayed for "BCTY", check for DTCs and perform troubleshooting based on the output DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>DTC CHECK / CLEAR).
Finish diagnostic mode (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR).
CALIBRATION WHEN SERVICING VEHICLE
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>CALIBRATION).