Home › Power Source / Network › 2AR-FE BATTERY / CHARGING › GENERATOR › 2011.10–2015.04
RM19V0EQ _57 Power Source / Network _014602 2AR-FE BATTERY / CHARGING _0074099 GENERATOR A

2AR-FE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A192789N02
1.615,0.792 0.552,0.792 false 1.49,1.146 0.938,1.146 0.938,1.146 0.938,0.792 false 0.198,0.708 0.51,0.896 0.313,0.188 10 SST

Using SST and a press, press in a new bearing.

SST
09950-60010  (09951-00520)
09950-70010  (09951-07100)


b.
A211515C02
2.719,1.427 2.417,1.99 2.417,1.99 2.323,1.99 true 2.094,0.49 2.177,0.49 2.177,0.49 2.76,0.938 true 1.927,0.396 2.094,0.583 0.167,0.188 10 *a 2.167,1.917 2.333,2.104 0.167,0.188 10 *b
*a Tab
*b Cutout


Fit the tabs on the bearing retainer into the cutouts on the drive end frame to install the bearing retainer.


c.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A192790

Place the generator drive end frame on the generator pulley.


b.

Install the generator rotor to the generator drive end frame.


c.
A297783

Place a new generator washer on the generator rotor.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A192792C02
1.604,0.677 0.844,0.531 0.844,0.531 0.719,0.531 false 0.5,0.458 0.698,0.635 0.198,0.177 10 *1
*1 Deep Socket Wrench (21 mm)


Using a 21 mm socket wrench and a press, slowly press in the generator coil.


b.
A192782

Install the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A079315C04
0.938,0.521 0.844,0.167 0.844,0.167 2.448,0.74 false 0.646,0.063 0.896,0.229 0.25,0.167 10 false *1
*1 Pin


While pushing the 2 brushes into the generator brush holder, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder.


b.
A192793C02
1.583,0.969 2.281,0.458 2.281,0.458 2.427,0.458 true 2.49,0.385 2.656,0.656 0.167,0.271 10 *1
*1 Pin


Install the generator brush holder with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull the pin out of the generator brush holder.


Hide 27039 5.INSTALL GENERATOR REAR END COVER

a.
A192780

Install the terminal insulator onto the generator coil assembly.


b.
A192779

Install the generator rear end cover with the 3 nuts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 6.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Temporarily install the generator pulley by hand.


b.

Mount the generator in a vise.


c.
A197238C01
1.635,1.063 1.635,1.344 false 2.51,1.458 2.667,1.375 2.667,1.375 2.833,1.375 true 1.563,1.344 1.771,1.542 0.208,0.198 10 false *1 2.844,1.281 3.375,1.479 0.531,0.198 10 false *2
*1 SST (A)
*2 SST (B)


Install SST (A) and (B) to the generator pulley as shown in the illustration.

SST
09820-63021  


d.
A256113C01
1.021,0.948 0.875,0.646 0.875,0.646 0.708,0.646 false 1.344,0.708 1.198,0.406 1.198,0.406 1.031,0.406 false 0.51,0.563 0.677,0.719 0.167,0.156 10 *1 0.844,0.323 1.01,0.479 0.167,0.156 10 *2 0.583,1.271 0.75,1.438 0.167,0.167 10 *a 1.542,2.031 1.708,2.198 0.167,0.167 10 *b
*1 SST (A)
*2 SST (B)
*a Fulcrum Length
100 mm (3.94 in.)
*b Fulcrum Length
255 mm (10.04 in.)


Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator pulley.

Torque:
without SST : 80 N*m (816 kgf*cm, 59 ft.*lbf)
with SST : 57 N*m (581 kgf*cm, 42 ft.*lbf)

NOTICE:
·

The "with SST" torque value is effective when using SST with a fulcrum length of 100 mm (3.94 in.) and a torque wrench with a fulcrum length of 255 mm (10.04 in.).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The "with SST" torque value is effective when SST is parallel to the torque wrench

·

Check that the drive end frame is secured in the vise tightly.

·

Hold SST (A) tightly during the operation.




e.

Check that the generator pulley rotates smoothly.


Hide 27416 7.INSTALL GENERATOR PULLEY CAP

a.
A194720

Install a new generator pulley cap to the pulley.