Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.10–2014.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE FUNCTION


a.

When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.


b.

The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)

Function Control Master System Related Fail-safe Operation Driver Detectable DTC Detection
(ECU that stored DTC)
Air conditioning control
·

Corrects engine speed, such as for idle up

·

Controls outlet air temperature, outlet mode change and airflow volume based on engine coolant temperature signal

·

Corrects engine coolant temperature map and changes compressor lock judgment value


Air conditioning amplifier assembly ECM Control is performed based on default coolant temperature of 80°C (176°F). - U0100
(Air conditioning amplifier assembly)
Compressor control
·

Judges compressor lock according to engine speed


Air conditioning amplifier assembly ECM Control is performed based on default engine speed of 0 rpm. - U0100
(Air conditioning amplifier assembly)
Simple load control
·

Performs electric load control according to load control level signal


Air conditioning amplifier assembly Power steering ECU assembly Load control is not performed. - U0131
(Air conditioning amplifier assembly)
Panel dimming control
·

Outputs dimmer signal to LIN connected panels according to display dimmer signal


Air conditioning amplifier assembly Main body ECU (Multiplex network body ECU) Dimming mode and non-dimming mode cannot be switched. - U0142
(Air conditioning amplifier assembly)
Destination identification control
·

Changes air conditioning control pattern according to destination


Air conditioning amplifier assembly Main body ECU (Multiplex network body ECU) Maintains the latest state. - U0142
(Air conditioning amplifier assembly)
Ambient temperature correction control
·

Switches air conditioning system operation condition and corrects value of displayed ambient temperature according to vehicle speed signal


Air conditioning amplifier assembly Combination meter assembly Control is performed based on default vehicle speed of 0 km/h (0 mph).
·

Correction level for displayed ambient temperature declines.

·

Correction level for outlet airflow declines.


U0155
(Air conditioning amplifier assembly)
Fuel Consumption display
·

Displays graph of fuel consumption per minute and history of total fuel consumption


·

Navigation ECU sub-assembly

·

Radio and display receiver assembly


·

ECM

·

Brake actuator assembly

·

Combination meter assembly


When communication with ECM or skid control ECU is interrupted:
·

Display is not updated.


When communication with combination meter is interrupted:
·

Display is not updated.

·

Numeric part of driveable mileage is cleared.


- U0100
U0129
U0155
(Navigation ECU sub-assembly)
(Radio and display receiver assembly)
Parking assist monitor control
·

Displays rear view monitor based on steering sensor, vehicle speed and vehicle information


Navigation ECU sub-assembly
·

Steering sensor

·

Main body ECU (Multiplex network body ECU)


When communication with steering angle sensor is interrupted:
·

Message is shown indicating that guide lines cannot be displayed.


- U0073
U0126
U0140
(Navigation ECU sub-assembly)
Destination identification
·

Identifies destination based on destination and destination package information, and selects the time zone and language used for the display


·

Navigation ECU sub-assembly

·

Radio and display receiver assembly


Main body ECU (Multiplex network body ECU) Destination is identified based on information received before communication is interrupted. Time zone and language selection screen are different from actual destination. U0140
(Navigation ECU sub-assembly)
(Radio and display receiver assembly)
Vehicle customization function
·

Allows changing of operation and control conditions for vehicle functions via multi-display operation


·

Navigation ECU sub-assembly

·

Radio and display receiver assembly


·

Smart key ECU assembly (Certification ECU)

·

Main body ECU (Multiplex network body ECU)


·

Customization via multi-display is not possible, but customization via main body ECU is possible.

·

When an application that uses remote communication is activated (customization/remote diagnosis), the process will be performed regardless of main body ECU remote communication permit/prohibit state.


Customizable items are not displayed. U0073
(Navigation ECU sub-assembly)
Door lock
·

Controls key linked and automatic door lock/unlock function, key confinement prevention function, etc.


Main body ECU (Multiplex network body ECU)
·

ECM

·

Combination meter assembly


·

Speed sensitive automatic lock control does not occur.

·

Shift linked automatic lock control does not occur.

·

Shift linked automatic unlock control does not occur.

·

Automatic lock/unlock cannot be changed.


- U0100
U0155
(Main body ECU (Multiplex network body ECU))
Display automatic dimming
·

Display dimming control


Main body ECU (Multiplex network body ECU) Combination meter assembly Automatic dimming control for displays does not operate when taillights are turned on. - U0155
(Main body ECU (Multiplex network body ECU))
Illumination control Main body ECU (Multiplex network body ECU)
·

ECM

·

Smart key ECU assembly (Certification ECU)


·

Interior lights turn off.

·

Inside handle light turn off.


When communication with smart key ECU is interrupted:
·

Interior lights do not turn off right after getting out of the vehicle.


U0100
U0327
(Main body ECU (Multiplex network body ECU))
Entry function/wireless control Main body ECU (Multiplex network body ECU) Smart key ECU assembly (Certification ECU) Entry lock/unlock control is not possible. - U0327
(Main body ECU (Multiplex network body ECU))
Electric load control
·

Performs idle up according to electric loads


ECM
·

Power steering ECU assembly

·

Main body ECU (Multiplex network body ECU)

·

Air conditioning amplifier assembly


Idle up according to electric loads is not performed. - -
Air conditioning cooperative operation
·

Performs idle up according to compressor load

·

Performs air conditioning cut control


ECM Air conditioning amplifier assembly Air conditioning system does not use cooperative controls.
(Idle up is not performed.)
Air conditioning system does not operate. -
Charge control
·

Performs idle up according to charging request


Smart key ECU assembly (Certification ECU)
·

Main body ECU (Multiplex network body ECU)

·

Air conditioning amplifier assembly


Idle up according to charging request is not performed. Taillights flicker and blower airflow changes. -
Eco control
·

Adjusts throttle response in consideration of actual fuel economy


ECM
·

Main body ECU (Multiplex network body ECU)

·

Air conditioning amplifier assembly


Eco mode does not operate. - -
Coast downshift timing change according to air conditioning load
·

Delays upshifts according to warm-up request


·

ECM

·

ECT


Air conditioning amplifier assembly Coast downshift does not occur. Coast downshift shock reduction performance deteriorates. -
Power steering control
·

Calculates assist current according to torque sensor value and vehicle speed and drives motor


Power steering ECU assembly
·

ECM

·

Brake actuator assembly


When communication with skid control ECU is interrupted:
·

Control continues based on a default speed of 140 km/h (87 mph) because vehicle speed is unrecognizable.


EPS warning light illuminates. U0100
U0129
(Power steering ECU assembly)
Steering assist calculation
·

Changes assist force based on vehicle speed


Power steering ECU assembly Brake actuator assembly Control continues based on a default speed of 140 km/h (87 mph) because vehicle speed is unrecognizable. EPS warning light illuminates. U0129
(Power steering ECU assembly)
Assist map selection
·

Selects proper assist map according to destination, engine type, etc.


Power steering ECU assembly
·

ECM

·

Brake actuator assembly


Default map is used to assist because proper assist map cannot be selected.
(Steering feel may be different.)
- C1582
(Power steering ECU assembly)
Entry function
·

Entry lock/unlock, entry luggage compartment open

·

Warning

·

Performs entry illumination

(Interior illumination etc)


·

Main body ECU (Multiplex network body ECU)

·

Smart key ECU assembly (Certification ECU)


·

Main body ECU (Multiplex network body ECU)

·

Combination meter assembly


Entry unlock is performed again.
·

Entry lock/unlock or entry luggage compartment open does not operate.

·

Warning functions (Key confinement, Key not in vehicle, Key reminder etc.) do not operate, Key confinement prevention control does not operate.

·

Entry illumination does not operate.


U0142
U0155
(Smart key ECU assembly (Certification ECU))
Wireless function
·

Locks and unlocks doors, etc. via remote operation


Main body ECU (Multiplex network body ECU) Smart key ECU assembly (Certification ECU) Wireless lock, unlock and luggage compartment opener do not operate. - -
Engine switch backlighting control
·

Turns on/off engine switch illumination linked with interior lights etc.


Smart key ECU assembly (Certification ECU) Main body ECU (Multiplex network body ECU) Engine switch backlighting does not illuminate according to interior lights operation. - U0142
(Smart key ECU assembly (Certification ECU))
Meter display
·

Displays vehicle condition and controls indicator lights


Combination meter assembly
·

ECM

·

Brake actuator assembly

·

Airbag sensor assembly

·

Power steering ECU assembly

·

Main body ECU (Multiplex network body ECU)


Lights do not illuminate or lights always illuminate. Lights do not illuminate properly or do not illuminate at all. U0100
U0129
U0131
U0142
U0151
(Combination meter assembly)
Vehicle speed display Combination meter assembly Brake actuator assembly Vehicle speed display remains at 0 km/h (0 mph). - U0129
(Combination meter assembly)
Tachometer
·

Displays engine speed


Combination meter assembly ECM The needle points at 0 rpm. - U0100
(Combination meter assembly)
Coolant temperature display Combination meter assembly ECM Display is turned off. - -
Engine start/stop switch
(Power source mode change)
·

Using start/stop switch signal as trigger, changes power source mode automatically and requests starter operation when conditions are met


Smart key ECU assembly (Certification ECU) ECM - - U0100
(Smart key ECU assembly (Certification ECU))
ABS/TRC/VSC control Brake actuator assembly
·

ECM

·

Steering sensor

·

Airbag sensor assembly


Control stops. Warning lights and indicators illuminate. U0073
U0100
U0123
U0126
(Brake actuator assembly)
Blind spot monitor control
·

Detects vehicle in blind spot of adjacent lane and informs driver


·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH


·

ECM

·

Steering sensor

·

Brake actuator assembly (Skid control ECU)

·

Main body ECU (Multiplex network body ECU)

·

Blind spot monitor sensor RH

·

Blind spot monitor sensor LH


Blind spot monitor control is prohibited. Blind spot monitor system warning light on the combination meter turns on. U0100
U0126
U0129
U0142
U0232
U0233
(Blind spot monitor sensor LH)
(Blind spot monitor sensor RH)
Gateway system
(Between V bus and sub bus 2)
·

Relays data between V bus and sub bus 2, and monitors ECUs connected to sub bus 2


-
·

Blind spot monitor sensor RH

·

Blind spot monitor sensor LH


Stagnant frame data in gateway is deleted by initializing CAN controller and communication software including gateway. - U0232
U0233
U1002
(Network gateway ECU)
Seat position memory system
·

Controls the seat position based on operation conditions


Position control ECU and switch assembly (for Driver side)
·

Main body ECU (Multiplex network body ECU)

·

ECM

·

Combination meter assembly

·

Smart key ECU assembly (Certification ECU)


Controls the seat position based on operation conditions. - -
Seat and mirror control Main body ECU (Multiplex network body ECU)
·

Position control ECU and switch assembly (for Driver side)

·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)

·

Smart key ECU assembly (Certification ECU)

·

Combination meter assembly


·

Memory function does not operate.

·

Mirrors cannot be adjusted.


- U0199
U0200
U0208
U0120
U0155
U0327
(Main body ECU (Multiplex network body ECU))
Seat memory switch signal forwarding
·

Sends switch operation status via MS-CAN


Main body ECU (Multiplex network body ECU)
·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)


Seat position memory settings cannot be memorized or recalled. - -
Memory call function
·

Recalls Seat position memory settings based on smart key information when door is unlocked


Main body ECU (Multiplex network body ECU)
·

Position control ECU and switch assembly (for Driver side)

·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)

·

Smart key ECU assembly (Certification ECU)

·

Combination meter assembly


Seat position cannot be memorized or recalled. - U0199
U0200
U0208
U0120
U0155
U0327
(Main body ECU (Multiplex network body ECU))
Mirror surface adjustment
·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)


Main body ECU (Multiplex network body ECU) Mirror surface position cannot be memorized or recalled. - U0142
(Outer mirror control ECU assembly)
Mirror surface position memory and recall
·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)


Main body ECU (Multiplex network body ECU) Mirror surface position cannot be memorized or recalled. - -
Reverse-shift linked door mirror operation
·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)


Main body ECU (Multiplex network body ECU) Reverse-shift linked door mirror operation. - -