Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"Power Steering (EPS)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Power steering ECU assembly branch line or connector

·

Power source circuit of power steering ECU assembly

·

Power steering ECU assembly ground circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C241661E19
2.49,1.281 2.333,0.75 2.333,0.75 2.219,0.75 false 4.229,1.281 3.885,0.375 3.885,0.375 3.604,0.375 false 4.927,3.542 5.125,3.802 0.198,0.26 10 false 2 4.344,3.729 4.896,3.969 0.552,0.24 10 false PGND 3.51,3.719 3.823,3.948 0.313,0.229 10 false IG 3.198,4.375 5.281,4.615 2.083,0.24 10 false Power Steering ECU Assembly 1.469,4.979 3.365,5.208 1.896,0.229 10 false : CAN Main Bus Line (CANH) 1.458,5.396 3.354,5.625 1.896,0.229 10 false : CAN Main Bus Line (CANL) 4.438,4.99 6.156,5.219 1.719,0.229 10 false : CAN Branch Line (CANH) 4.438,5.396 6.156,5.625 1.719,0.229 10 false : CAN Branch Line (CANL) 5.615,4.01 6.563,4.24 0.948,0.229 10 false Trouble Area 3.667,3.365 4.156,3.552 0.49,0.188 10 false CANH 4.125,3.375 4.583,3.583 0.458,0.208 10 false CANL 3.552,3.167 3.823,3.396 0.271,0.229 10 false 4 3.208,3.521 3.469,3.771 0.26,0.25 10 false 1 4.51,3.156 4.729,3.375 0.219,0.219 10 false 8 0.208,0.646 2.24,0.979 2.031,0.333 10 false CAN No. 2 Junction Connector 1.625,0.281 3.688,0.573 2.063,0.292 10 false CAN No. 1 Junction Connector 2.479,3.906 3.135,4.177 0.656,0.271 10 false EPS-IG1 0.729,2.208 1.24,2.448 0.51,0.24 10 false 120 Ω 6.188,2.208 6.677,2.396 0.49,0.188 10 false 120 Ω 4.594,0.583 5.083,0.854 0.49,0.271 10 false DLC3 5.906,2.823 7.073,3.271 1.167,0.448 10 false Combination Meter Assembly 0.813,2.833 1.292,3.104 0.479,0.271 10 false ECM 3.823,3.156 4.073,3.385 0.25,0.229 10 false j1 4.208,3.156 4.531,3.375 0.323,0.219 10 false j1 0.094,0.135 1.552,0.521 1.458,0.385 12 false V Bus (for LHD): 3.208,3.708 3.479,4 0.271,0.292 10 false j1 4.917,3.729 5.135,4 0.219,0.271 10 false j2 5.646,2.813 5.958,3 0.313,0.188 10 false I18 0.5,2.823 0.875,3.052 0.375,0.229 10 false A25

C241449E17
2.667,1.25 3.021,0.635 3.021,0.635 3.292,0.635 false 4.344,1.26 4.521,0.917 4.521,0.917 4.677,0.917 false 4.885,3.51 5.104,3.729 0.219,0.219 10 false 2 4.302,3.688 4.76,3.875 0.458,0.188 10 false PGND 3.469,3.688 3.719,3.917 0.25,0.229 10 false IG 1.396,4.948 3.292,5.177 1.896,0.229 10 false : CAN Main Bus Line (CANH) 1.396,5.365 3.292,5.594 1.896,0.229 10 false : CAN Main Bus Line (CANL) 4.365,4.958 6.083,5.188 1.719,0.229 10 false : CAN Branch Line (CANH) 4.365,5.365 6.063,5.594 1.698,0.229 10 false : CAN Branch Line (CANL) 5.563,3.927 6.594,4.271 1.031,0.344 10 false Trouble Area 3.615,3.333 4.125,3.542 0.51,0.208 10 false CANH 4.104,3.333 4.583,3.552 0.479,0.219 10 false CANL 3.521,3.146 3.729,3.333 0.208,0.188 10 false 4 3.156,3.5 3.385,3.688 0.229,0.188 10 false 1 4.469,3.135 4.688,3.313 0.219,0.177 10 false 8 3.344,0.542 5.344,0.792 2,0.25 10 false CAN No. 2 Junction Connector 4.74,0.813 6.75,1.052 2.01,0.24 10 false CAN No. 1 Junction Connector 2.417,3.865 3.104,4.104 0.688,0.24 10 false EPS-IG1 0.667,2.177 1.156,2.396 0.49,0.219 10 false 120 Ω 6.156,2.188 6.667,2.448 0.51,0.26 10 false 120 Ω 2.146,0.552 2.604,0.792 0.458,0.24 10 false DLC3 0.344,2.792 1.521,3.26 1.177,0.469 10 false Combination Meter Assembly 6.271,2.792 6.698,2.99 0.427,0.198 10 false ECM 3.781,3.135 3.99,3.375 0.208,0.24 10 false j1 4.188,3.135 4.427,3.375 0.24,0.24 10 false j1 0.104,0.115 1.521,0.51 1.417,0.396 12 false V Bus (for RHD): 3.156,3.698 3.323,3.896 0.167,0.198 10 false j1 4.885,3.698 5.104,3.938 0.219,0.24 10 false j2 0.094,2.792 0.417,3.083 0.323,0.292 10 false I18 5.969,2.792 6.323,3 0.354,0.208 10 false A25 3.115,4.344 5.26,4.635 2.146,0.292 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 6 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power steering ECU assembly connector.


c.
C248206C09
0.615,1.573 0.99,1.823 0.375,0.25 1.979,2.313 2.292,2.313 false 1.979,2.542 2.292,2.542 false 0.177,0.094 0.365,0.281 0.188,0.188 10 false *a 0.74,1.604 1.094,1.865 0.354,0.26 10 false j1 2.354,2.469 2.802,2.656 0.448,0.188 10 false CANL 2.354,2.24 2.802,2.427 0.448,0.188 10 false CANH
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-4 (CANH) - j1-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the power steering ECU assembly connector.


b.
C240535C13
0.156,1.531 0.646,1.823 0.49,0.292 2.281,1.688 2.281,0.74 2.281,0.74 2.5,0.74 false 0.115,0.167 0.427,0.521 0.313,0.354 10 false *a 2.594,0.656 3.219,0.917 0.625,0.26 10 false PGND 0.354,1.573 0.542,1.75 0.188,0.177 10 false j2
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j2-2 (PGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Connect the cable to the negative (-) battery terminal.


d.
C248206C10
2.333,1.917 2.708,2.167 0.375,0.25 1.094,2.271 1.396,2.271 false 0.177,0.094 0.365,0.281 0.188,0.188 10 false *a 2.458,1.948 3.031,2.24 0.573,0.292 10 false j1 0.875,2.188 1.063,2.375 0.188,0.188 10 false IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j1-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)