Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.10–2014.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Lines for Short Circuit (RHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Combination meter assembly

·

Brake actuator assembly

·

Steering sensor

·

Network gateway ECU*1

·

Power steering ECU assembly

·

Airbag sensor assembly

·

Air conditioning amplifier assembly

·

Smart key ECU assembly (Certification ECU)*2

·

Navigation ECU sub-assembly*3

·

Radio and display receiver assembly*4

·

AFS ECU*5

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector



*1: w/ Blind spot monitor system

*2: w/ Smart entry and start system

*3: for Navigation receiver type

*4: for Radio and display type

*5: w/ Automatic high beam system

WIRING DIAGRAM

C247970E05
3.948,7.99 5.677,8.177 1.729,0.188 10 false : CAN Branch Line (CANH) 3.948,8.406 5.677,8.594 1.729,0.188 10 false : CAN Branch Line (CANL) 0.823,8.01 2.74,8.198 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.823,8.427 2.74,8.615 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.448,0.354 3.865,0.542 0.417,0.188 10 false 120 Ω 2.792,1 3.198,1.167 0.406,0.167 10 false CANL 1.052,4 1.458,4.167 0.406,0.167 10 false CANL 0.406,0.594 0.771,0.76 0.365,0.167 10 false I18 4.094,1.438 4.229,1.604 0.135,0.167 10 false R 2,4.073 2.167,4.24 0.167,0.167 10 false W 5.177,4.969 5.375,5.229 0.198,0.26 10 false W 3.031,1.438 3.229,1.604 0.198,0.167 10 false W 4.104,7.375 4.24,7.542 0.135,0.167 10 false B 3.031,7.375 3.198,7.542 0.167,0.167 10 false W 0.125,4.271 0.344,4.438 0.219,0.167 10 false I29 0.688,0.594 2.542,0.792 1.854,0.198 10 false Combination Meter Assembly 4.115,1 4.552,1.167 0.438,0.167 10 false CANH 1.042,3.396 1.479,3.563 0.438,0.167 10 false CANH 6.042,4.75 6.448,4.917 0.406,0.167 10 false CANL 5.865,4.427 6.302,4.594 0.438,0.167 10 false CANH 4.063,1.208 4.271,1.375 0.208,0.167 10 false 16 2.698,5.354 2.906,5.521 0.208,0.167 10 false 1 2.698,6.073 2.906,6.24 0.208,0.167 10 false 2 2.729,3.313 2.938,3.479 0.208,0.167 10 false 1 2.729,4.083 2.938,4.25 0.208,0.167 10 false 2 1.542,3.406 1.75,3.573 0.208,0.167 10 false 3 4.479,2.979 4.583,3.146 0.104,0.167 10 false 2 1.563,3.979 1.771,4.146 0.208,0.167 10 false 2 4.479,4.271 4.688,4.438 0.208,0.167 10 false 1 4.479,4.99 4.688,5.156 0.208,0.167 10 false 2 2,3.313 2.229,3.479 0.229,0.167 10 false V 2.938,1.813 3.063,1.979 0.125,0.167 10 false 2 3.031,1.208 3.219,1.375 0.188,0.167 10 false 15 4.49,2.219 4.604,2.385 0.115,0.167 10 false 1 4.25,1.802 4.365,1.969 0.115,0.167 10 false 1 2.938,7.125 3.063,7.292 0.125,0.167 10 false 2 4.25,7.125 4.365,7.292 0.115,0.167 10 false 1 5.802,4.885 6,5.052 0.198,0.167 10 false 14 5.656,4.354 5.833,4.521 0.177,0.167 10 false 6 5.156,0.458 6.365,0.646 1.208,0.188 10 false x: Suspected Area 6.083,4.99 6.406,5.177 0.323,0.188 10 false I39 6.365,4.99 6.76,5.177 0.396,0.188 10 false DLC3 0.406,4.271 1.479,4.479 1.073,0.208 10 false Steering Sensor 0.844,2.177 2.833,2.427 1.99,0.25 10 false CAN No. 2 Junction Connector 5.177,4.25 5.365,4.5 0.188,0.25 10 false G 2.615,5.896 2.906,6.083 0.292,0.188 10 false I105 2.615,5.531 2.906,5.719 0.292,0.188 10 false I105 2.667,3.865 2.885,4.052 0.219,0.188 10 false I97 2.667,3.521 2.885,3.708 0.219,0.188 10 false I97 3.177,1.823 3.406,2.01 0.229,0.188 10 false I94 3.948,1.823 4.167,2.01 0.219,0.188 10 false I94 4.417,2.417 4.708,2.604 0.292,0.188 10 false I106 4.417,2.781 4.708,2.969 0.292,0.188 10 false I106 4.438,4.448 4.656,4.635 0.219,0.188 10 false I96 4.438,4.802 4.656,4.99 0.219,0.188 10 false I96 3.146,7.094 3.448,7.281 0.302,0.188 10 false I101 3.896,7.094 4.198,7.281 0.302,0.188 10 false I101 0.406,6.344 2.208,6.698 1.802,0.354 10 false Brake Actuator Assembly 1.063,6 1.469,6.167 0.406,0.167 10 false CANL 1.052,5.448 1.49,5.615 0.438,0.167 10 false CANH 2.302,5.333 2.448,5.5 0.146,0.167 10 false Y 2.302,6.083 2.448,6.25 0.146,0.167 10 false W 1.729,5.333 1.958,5.5 0.229,0.167 10 false GR 1.771,6.083 1.917,6.25 0.146,0.167 10 false W 0.125,6.344 0.427,6.521 0.302,0.177 10 false A49 1.531,5.417 1.823,5.646 0.292,0.229 10 false 26 1.531,6.031 1.719,6.198 0.188,0.167 10 false 14 5.823,2.875 6.229,3.042 0.406,0.167 10 false CANL 5.823,2.302 6.26,2.469 0.438,0.167 10 false CANH 5.115,2.25 5.26,2.417 0.146,0.167 10 false L 5.115,2.979 5.26,3.146 0.146,0.167 10 false W 5.573,2.323 5.76,2.49 0.188,0.167 10 false 14 5.583,2.875 5.771,3.042 0.188,0.167 10 false 15 4.969,3.156 5.229,3.323 0.26,0.167 10 false I78 5.25,3.156 6.948,3.563 1.698,0.406 10 false Smart Key ECU Assembly (Certification ECU)*1 0.188,6.854 2.49,7.125 2.302,0.271 10 false *1: w/ Smart Entry and Start System 0.188,7.177 2.635,7.646 2.448,0.469 10 false *2: w/ Automatic High Beam System 4.5,6.083 4.708,6.25 0.208,0.167 10 false 1 4.5,6.823 4.708,6.99 0.208,0.167 10 false 2 4.406,6.646 4.698,6.833 0.292,0.188 10 false I112 4.406,6.281 4.698,6.469 0.292,0.188 10 false I112 4.833,6.052 5.063,6.219 0.229,0.167 10 false BE 4.865,6.865 5.01,7.031 0.146,0.167 10 false W 5.417,6.052 5.646,6.219 0.229,0.167 10 false B 5.417,6.854 5.563,7.021 0.146,0.167 10 false W 5.865,6.167 6.302,6.333 0.438,0.167 10 false MPX1 5.813,7.083 6.135,7.271 0.323,0.188 10 false A35 6.094,7.083 6.927,7.333 0.833,0.25 10 false AFS ECU*2 5.865,6.781 6.302,6.948 0.438,0.167 10 false MPX2 5.604,6.135 5.792,6.302 0.188,0.167 10 false 12 5.604,6.792 5.823,6.99 0.219,0.198 10 false 13

C248845E03
0.802,9.052 2.719,9.24 1.917,0.188 10 false : CAN Main Bus Line (CANH) 3.958,9.073 5.677,9.26 1.719,0.188 10 false : CAN Branch Line (CANH) 3.958,9.458 5.677,9.646 1.719,0.188 10 false : CAN Branch Line (CANL) 0.802,9.438 2.719,9.625 1.917,0.188 10 false : CAN Main Bus Line (CANL) 4.427,6.229 6.417,6.417 1.99,0.188 10 false CAN No. 1 Junction Connector 2.771,8.073 3.177,8.24 0.406,0.167 10 false CANL 4.104,8.094 4.542,8.26 0.438,0.167 10 false CANH 1.052,1.969 1.458,2.135 0.406,0.167 10 false CANL 1.042,1.385 1.479,1.552 0.438,0.167 10 false CANH 1.031,4.344 1.438,4.51 0.406,0.167 10 false CANL 1.031,3.771 1.469,3.938 0.438,0.167 10 false CANH 1.563,1.396 1.677,1.563 0.115,0.167 10 false 9 2.052,1.302 2.24,1.469 0.188,0.167 10 false R 2.052,2.042 2.25,2.208 0.198,0.167 10 false W 1.521,1.969 1.698,2.135 0.177,0.167 10 false 10 1.51,3.792 1.74,3.958 0.229,0.167 10 false 11 2.073,3.646 2.188,3.813 0.115,0.167 10 false V 2.052,4.448 2.219,4.615 0.167,0.167 10 false W 1.51,4.333 1.688,4.5 0.177,0.167 10 false 12 4.49,0.729 4.677,0.896 0.188,0.167 10 false 1 2.917,6.521 3.104,6.688 0.188,0.167 10 false 2 4.229,6.521 4.417,6.688 0.188,0.167 10 false 1 2.917,0.563 3.104,0.729 0.188,0.167 10 false 2 4.229,0.563 4.417,0.729 0.188,0.167 10 false 1 4.49,1.51 4.677,1.677 0.188,0.167 10 false 2 2.688,1.302 2.875,1.469 0.188,0.167 10 false 1 2.688,2.073 2.875,2.24 0.188,0.167 10 false 2 2.688,3.667 2.875,3.833 0.188,0.167 10 false 1 2.688,4.427 2.875,4.594 0.188,0.167 10 false 2 2.688,5.448 2.875,5.615 0.188,0.167 10 false 1 2.688,6.177 2.875,6.344 0.188,0.167 10 false 2 4.469,2.604 4.656,2.771 0.188,0.167 10 false 1 4.469,3.375 4.656,3.542 0.188,0.167 10 false 2 4.146,7.552 4.292,7.719 0.146,0.167 10 false B 3.01,7.552 3.156,7.719 0.146,0.167 10 false W 4.146,6.833 4.448,7.125 0.302,0.292 10 false G 3,6.833 3.167,7 0.167,0.167 10 false W 4.219,7.885 4.406,8.052 0.188,0.167 10 false 13 2.917,7.885 3.104,8.052 0.188,0.167 10 false 26 0.188,8.677 1.396,8.865 1.208,0.188 10 false x: Suspected Area 3.469,8.677 3.979,8.865 0.51,0.188 10 false 120 Ω 0.365,2.26 2.625,2.594 2.26,0.333 10 false Navigation ECU Sub-assembly*1 0.146,4.646 0.438,4.823 0.292,0.177 10 false I77 0.396,4.646 1.979,5.021 1.583,0.375 10 false Air Conditioning Amplifier Assembly 4.635,8.375 5.021,8.573 0.385,0.198 10 false ECM 4.635,8.219 5.021,8.417 0.385,0.198 10 false A25 0.438,2.917 2.26,3.271 1.823,0.354 10 false Radio and Display Receiver Assembly*2 0.094,2.917 0.417,3.083 0.323,0.167 10 false I155 0.177,6.979 2.438,7.354 2.26,0.375 10 false *1: for Navigation Receiver Type 0.177,7.313 2.438,7.698 2.26,0.385 10 false *2: for Radio and Display Type 0.094,2.271 0.417,2.438 0.323,0.167 10 false I67 2.594,4.24 2.885,4.406 0.292,0.167 10 false I102 2.594,3.865 2.885,4.031 0.292,0.167 10 false I102 2.594,5.625 2.885,5.792 0.292,0.167 10 false I161 2.594,5.99 2.885,6.156 0.292,0.167 10 false I161 3.156,0.563 3.448,0.729 0.292,0.167 10 false I93 3.917,0.563 4.219,0.729 0.302,0.167 10 false I93 4.406,0.938 4.698,1.104 0.292,0.167 10 false I100 4.406,1.313 4.698,1.479 0.292,0.167 10 false I100 4.385,3.198 4.677,3.365 0.292,0.167 10 false I103 4.385,2.813 4.677,2.979 0.292,0.167 10 false I103 3.115,6.51 3.406,6.677 0.292,0.167 10 false I104 3.875,6.5 4.177,6.667 0.302,0.167 10 false I104 2.594,1.51 2.885,1.677 0.292,0.167 10 false I107 2.594,1.875 2.885,2.042 0.292,0.167 10 false I107 4.854,0.76 5.052,0.99 0.198,0.229 10 false L 4.854,1.5 5.063,1.74 0.208,0.24 10 false W 5.344,0.76 5.542,0.99 0.198,0.229 10 false Y 5.344,1.5 5.552,1.74 0.208,0.24 10 false SB 5.813,1.406 6.219,1.573 0.406,0.167 10 false CANL 5.813,0.813 6.25,0.979 0.438,0.167 10 false CANH 5.635,1.406 5.781,1.625 0.146,0.219 10 false 8 5.635,0.854 5.781,1.115 0.146,0.26 10 false 4 5.583,1.677 5.74,1.833 0.156,0.156 10 false j1 5.75,1.698 7.125,2.135 1.375,0.438 10 false Power Steering ECU Assembly 5.156,3.365 5.323,3.531 0.167,0.167 10 false W 5.156,2.615 5.323,2.781 0.167,0.167 10 false Y 5.792,3.313 6.198,3.479 0.406,0.167 10 false CANL 5.792,2.729 6.229,2.896 0.438,0.167 10 false CANH 5.563,3.313 5.771,3.479 0.208,0.167 10 false 22 5.552,2.698 5.729,2.865 0.177,0.167 10 false 13 5.219,3.563 5.563,3.76 0.344,0.198 10 false I47 5.51,3.563 7.104,3.75 1.594,0.188 10 false Airbag Sensor Assembly 5.823,5.167 6.229,5.333 0.406,0.167 10 false CANL 5.156,5.24 5.323,5.406 0.167,0.167 10 false W 5.104,5.458 5.469,5.625 0.365,0.167 10 false I13 5.823,4.552 6.26,4.719 0.438,0.167 10 false CANH 5.51,4.5 5.74,4.719 0.229,0.219 10 false 14 5.51,5.167 5.74,5.385 0.229,0.219 10 false 13 5.156,4.438 5.333,4.583 0.177,0.146 10 false P 5.375,5.448 7.115,5.99 1.74,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 1.031,6.094 1.438,6.26 0.406,0.167 10 false CA1L 1.031,5.531 1.469,5.698 0.438,0.167 10 false CA1H 1.531,5.469 1.76,5.635 0.229,0.167 10 false 16 1.531,6.125 1.708,6.292 0.177,0.167 10 false 15 2.042,5.406 2.354,5.573 0.313,0.167 10 false BE 2.052,6.198 2.219,6.365 0.167,0.167 10 false W 4.417,5.042 4.708,5.208 0.292,0.167 10 false I95 4.417,4.667 4.708,4.833 0.292,0.167 10 false I95 4.458,4.469 4.646,4.635 0.188,0.167 10 false 1 4.458,5.25 4.646,5.417 0.188,0.167 10 false 2 0.104,6.406 0.396,6.583 0.292,0.177 10 false I160 0.417,6.406 2.344,6.74 1.927,0.333 10 false Network Gateway ECU*3 0.177,7.667 2.354,8.198 2.177,0.531 10 false *3: w/ Blind Spot Monitor System

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C247973C01
1.469,1.688 1.854,1.927 0.385,0.24 2.302,2.25 2.583,2.063 2.583,2.063 2.677,2.063 false 2.313,2.438 2.594,2.583 2.594,2.583 2.688,2.583 false 2.063,2.323 1.896,2.146 1.896,2.146 1.708,2.146 false 2.156,2.448 1.896,2.854 1.896,2.854 1.781,2.854 false 0.083,0.073 0.333,0.271 0.25,0.198 10 false *a 2.708,1.99 3.281,2.229 0.573,0.24 10 false CANH*b 2.719,2.51 3.271,2.74 0.552,0.229 10 false CANL*b 1.573,2.073 1.729,2.26 0.156,0.188 10 false G 1.625,2.792 1.844,2.979 0.219,0.188 10 false W 1.563,1.729 1.771,1.917 0.208,0.188 10 false I96
*a Rear view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to DLC3


Disconnect the DLC3 branch line connector (I96) from the CAN No. 2 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C210421C06
1.51,0.698 1.948,1 0.438,0.302 2.073,1.854 2.281,1.344 2.281,1.344 2.469,1.344 false 2.083,2.531 2.198,2.885 2.198,2.885 2.375,2.885 false 0.083,0.125 0.927,0.458 0.844,0.333 10 false *1 1.646,0.76 1.948,0.938 0.302,0.177 10 false I39 2.531,1.25 2.938,1.427 0.406,0.177 10 false CANH 2.458,2.813 2.844,2.99 0.385,0.177 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES (BRANCH LINE)

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT IN CAN BUS LINES (BRANCH LINE)
a.

Reconnect the DLC3 branch line connector (I96) to the CAN No. 2 junction connector.


b.
C210421C08
1.49,0.698 1.927,1 0.438,0.302 2.073,1.854 2.25,1.365 2.25,1.365 2.438,1.365 false 2.083,2.552 2.219,2.958 2.219,2.958 2.385,2.958 false 0.104,0.125 0.948,0.458 0.844,0.333 10 false *1 1.615,0.76 1.917,0.938 0.302,0.177 10 false I39 2.51,1.281 2.917,1.458 0.406,0.177 10 false CANH 2.438,2.896 2.823,3.073 0.385,0.177 10 false CANL
*1 DLC3


Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.


c.

While observing the resistance value shown on the tester, disconnect connectors (I95, I97, I103, I100, I107, I106, I105, I102, I112 and I161) from the CAN No. 1 junction connector or CAN No. 2 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

HINT:

Disconnect the branch line connectors other than those of the DLC3.


C248846C01
2.854,4.219 3.208,4.479 0.354,0.26 10 false *10 3.406,6.313 3.823,6.625 0.417,0.313 10 false *16 2.698,5.5 2.854,5.677 0.156,0.177 10 false L 1.677,5.719 1.833,5.896 0.156,0.177 10 false G 2.167,5.708 2.323,5.885 0.156,0.177 10 false W 3.396,0.323 3.906,0.635 0.51,0.313 10 false *15 1.896,4.875 2.177,5.25 0.281,0.375 10 false *9 3.167,5.5 3.323,5.677 0.156,0.177 10 false W 2.698,4.802 2.854,4.979 0.156,0.177 10 false Y 3.167,4.802 3.406,4.979 0.24,0.177 10 false SB 4.156,5.479 4.313,5.656 0.156,0.177 10 false W 3.677,5.479 3.833,5.656 0.156,0.177 10 false Y 5.198,5.135 5.354,5.313 0.156,0.177 10 false W 4.708,5.146 4.865,5.323 0.156,0.177 10 false V 1.229,5.083 1.385,5.26 0.156,0.177 10 false W 0.771,5.083 0.927,5.26 0.156,0.177 10 false R 5.677,4.875 6.052,5.156 0.375,0.281 10 false *13 3.823,4.875 4.208,5.208 0.385,0.333 10 false *11 4.875,4.208 5.26,4.49 0.385,0.281 10 false *12 2.49,2.406 2.844,2.656 0.354,0.25 10 false *3 6.052,0.99 6.208,1.167 0.156,0.177 10 false W 5.542,0.99 5.698,1.167 0.156,0.177 10 false R 4.771,2.396 5.271,2.688 0.5,0.292 10 false *5 1.448,1.677 1.74,1.938 0.292,0.26 10 false *2 4.531,1.438 4.688,1.615 0.156,0.177 10 false G 5.031,1.438 5.188,1.615 0.156,0.177 10 false W 1.698,1.01 1.854,1.188 0.156,0.177 10 false W 1.229,1.01 1.385,1.188 0.156,0.177 10 false V 2.292,0.99 2.448,1.167 0.156,0.177 10 false Y 2.771,0.99 2.927,1.167 0.156,0.177 10 false W 0.083,3.552 0.24,3.729 0.156,0.177 10 false B 0.542,3.563 0.698,3.74 0.156,0.177 10 false W 5.958,5.5 6.115,5.677 0.156,0.177 10 false W 5.51,5.521 5.667,5.698 0.156,0.177 10 false P 6.385,2.188 6.542,2.365 0.156,0.177 10 false B 6.865,2.188 7.021,2.365 0.156,0.177 10 false W 6.938,5.365 7.094,5.542 0.156,0.177 10 false W 6.292,5.375 6.563,5.552 0.271,0.177 10 false BE 6.448,4.219 7.073,4.5 0.625,0.281 10 false *14 (*E) 2.198,1.813 2.448,1.99 0.25,0.177 10 false GR 2.781,1.823 2.938,2 0.156,0.177 10 false W 3.521,0.99 3.677,1.167 0.156,0.177 10 false L 4.021,0.99 4.177,1.167 0.156,0.177 10 false W 0.854,4.125 1.354,4.417 0.5,0.292 10 false *7 (*C) 0.854,4.313 1.396,4.573 0.542,0.26 10 false *8 (*D) 1.688,5.24 1.844,5.417 0.156,0.177 10 false B 2.167,5.24 2.323,5.417 0.156,0.177 10 false W 5.813,1.667 6.313,1.958 0.5,0.292 10 false *6 3.646,1.667 4.146,1.958 0.5,0.292 10 false *4 (*B) 0.271,1.781 0.427,1.958 0.156,0.177 10 false B 0.75,1.781 0.906,1.958 0.156,0.177 10 false W 0.177,1 0.427,1.177 0.25,0.177 10 false BE 0.771,1.01 0.927,1.188 0.156,0.177 10 false W 0.344,2.406 0.844,2.698 0.5,0.292 10 false *1 (*A)
*A w/ Automatic High Beam System *B w/ Smart Entry and Start System
*C for Navigation Receiver Type *D for Radio and Display Type
*E w/ Blind Spot Monitor System - -
*1 AFS ECU *2 Steering Sensor
*3 Brake Actuator Assembly *4 Smart Key ECU Assembly (Certification ECU)
*5 DLC3 *6 Combination Meter Assembly
*7 Navigation ECU Sub-assembly *8 Radio and Display Receiver Assembly
*9 ECM *10 Power Steering ECU Assembly
*11 Airbag Sensor Assembly *12 Air Conditioning Amplifier Assembly
*13 Main Body ECU (Multiplex Network Body ECU) *14 Network Gateway ECU
*15 CAN No. 2 Junction Connector *16 CAN No. 1 Junction Connector


C247977C01
3.583,2.302 3.875,2.469 0.292,0.167 10 false I101 3.615,2.573 3.833,2.74 0.219,0.167 10 false I94 3.583,3.406 3.875,3.573 0.292,0.167 10 false I105 3.615,2.854 3.833,3.021 0.219,0.167 10 false I96 3.583,3.135 3.875,3.302 0.292,0.167 10 false I106 3.615,3.708 3.833,3.875 0.219,0.167 10 false I97 2.333,0.427 2.594,0.677 0.26,0.25 10 false *a 3.583,4 3.875,4.167 0.292,0.167 10 false I112
*a Component without harness connected
(to CAN No. 2 Junction Connector)
- -


Wiring Color:
CAN No. 1 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I101 B W
Combination meter assembly I94 R W
DLC3 I96 G W
Smart key ECU assembly (Certification ECU)*1 I106 L W
Brake actuator assembly I105 Y W
Steering sensor I97 V W
AFS ECU*2 I112 BE W


*1: w/ Smart entry and start system

*2: w/ Automatic high beam system


C247978C01
3.354,2.604 3.802,2.771 0.448,0.167 10 false I95 3.313,2.323 3.76,2.49 0.448,0.167 10 false I161 3.313,3.156 3.76,3.323 0.448,0.167 10 false I103 3.313,2.875 3.76,3.042 0.448,0.167 10 false I102 3.344,4.25 3.792,4.417 0.448,0.167 10 false I93 3.313,3.979 3.76,4.146 0.448,0.167 10 false I107 3.313,3.438 3.76,3.604 0.448,0.167 10 false I100 2.427,0.385 2.625,0.583 0.198,0.198 10 false *a 3.313,3.708 3.76,3.875 0.448,0.167 10 false I104
*a Component without harness connected
(to CAN No. 1 Junction Connector)
- -


Wiring Color:
CAN No. 2 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
Network gateway ECU*3 I161 BE W
Main body ECU (Multiplex network body ECU) I95 P W
Air conditioning amplifier assembly I102 V W
Airbag sensor assembly I103 Y W
Power steering ECU assembly I100 L W
ECM I104 G W
·

Navigation ECU sub-assembly*1

·

Radio and display receiver assembly*2


I107 R W
CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I93 B W


*1: for Navigation receiver type

*2: for Radio and display type

*3: w/ Blind spot monitor system


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.



Result:
Symptom Proceed to
The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.) A
The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) B


d.

When there is a short in one or more of the branch lines:

i.

Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69Ω) to confirm that there is a short in the one branch line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.






A

3.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)

B

9.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
3.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)
a.
C247980C01
1.771,1.802 2.135,2.031 0.365,0.229 2.552,2.177 2.656,1.865 2.656,1.865 2.771,1.865 false 2.552,2.323 2.885,2.406 2.885,2.406 2.885,2.604 false 2.406,2.354 2.188,2.719 2.188,2.719 2.083,2.719 false 2.333,2.24 2.135,2.156 2.135,2.156 2.042,2.156 false 0.083,0.094 0.323,0.344 0.24,0.25 10 false *a 2.802,1.792 3.375,1.969 0.573,0.177 10 false CANH*b 2.625,2.615 3.24,2.865 0.615,0.25 10 false CANL*b 1.927,2.083 2.083,2.26 0.156,0.177 10 false R 1.938,2.635 2.135,2.813 0.198,0.177 10 false W 1.854,1.833 2.073,2.01 0.219,0.177 10 false I94
*a Rear view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Combination Meter Assembly


Disconnect the combination meter assembly main bus line connector (I94) from the CAN No. 2 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




b.
C210421C09
1.5,0.688 1.938,0.99 0.438,0.302 2.073,1.865 2.229,1.385 2.229,1.385 2.448,1.385 false 2.052,2.563 2.219,3.021 2.219,3.021 2.396,3.021 false 0.104,0.115 0.948,0.448 0.844,0.333 10 *1 1.615,0.76 1.917,0.938 0.302,0.177 10 I39 2.521,1.302 2.927,1.479 0.406,0.177 10 CANH 2.448,2.948 2.833,3.125 0.385,0.177 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Symptom Proceed to
The resistance is still below 54 Ω when the combination meter assembly connector is disconnected. (There are no shorts in the combination meter assembly or between its main bus lines.) A
The resistance falls within the specified range (between 108 and 132 Ω) (the other terminating resistor is normal) when the combination meter assembly connector is disconnected. (There is a short in the combination meter assembly or between its main bus lines.) B



A

4.CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN LINE)

B

8.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY)
4.CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN LINE)
a.
C247981C01
1.354,2.146 1.76,2.417 0.406,0.271 2.406,2.146 2.531,1.99 2.531,1.99 2.677,1.99 false 2.417,2.292 2.552,2.427 2.552,2.427 2.677,2.427 false 2.177,2.219 1.969,1.99 1.969,1.99 1.875,1.99 false 2.24,2.344 2.448,2.729 2.448,2.729 2.542,2.729 false 0.125,0.104 0.365,0.354 0.24,0.25 10 false *a 2.719,1.896 3.292,2.146 0.573,0.25 10 false CANH*b 2.719,2.344 3.281,2.594 0.563,0.25 10 false CANL*b 2.583,2.646 2.771,2.844 0.188,0.198 10 false W 1.708,1.917 1.865,2.104 0.156,0.188 10 false G 1.417,2.198 1.719,2.385 0.302,0.188 10 false I104
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM


Disconnect the ECM main bus line connector (I104) from the CAN No. 1 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




b.
C210421C10
1.5,0.688 1.938,0.99 0.438,0.302 2.063,1.875 2.198,1.354 2.198,1.354 2.406,1.354 false 2.063,2.573 2.229,2.958 2.229,2.958 2.375,2.958 false 0.083,0.104 0.927,0.438 0.844,0.333 10 false *1 1.615,0.76 1.917,0.938 0.302,0.177 10 false I39 2.458,1.281 2.865,1.458 0.406,0.177 10 false CANH 2.417,2.885 2.802,3.063 0.385,0.177 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher


HINT:

Measure the resistance with the combination meter assembly main bus line connector (I94) disconnected.



Result:
Symptom Proceed to
The resistance is still below 1 MΩ when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.) A
The resistance becomes 1 MΩ or more when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.) B



A

5.CHECK CAN NO.2 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT IN CAN BUS LINES (ECM)
5.CHECK CAN NO.2 JUNCTION CONNECTOR
a.
C251600C02
2.74,1.271 3.125,1.531 0.385,0.26 2.875,2.135 2.417,1.719 2.417,1.719 2.167,1.719 false 2.875,2.354 2.875,2.698 2.875,2.698 2.198,2.698 false 2.729,2.229 2.458,1.896 2.458,1.896 2.323,1.896 false 2.792,2.344 2.531,2.198 2.531,2.198 2.406,2.198 false 0.135,0.125 0.479,0.375 0.344,0.25 10 false *a 1.604,1.646 2.25,1.865 0.646,0.219 10 false CANH*b 1.646,2.615 2.292,2.833 0.646,0.219 10 false CANL*b 2.198,1.823 2.365,2.031 0.167,0.208 10 false B 2.219,2.135 2.385,2.344 0.167,0.208 10 false W 2.802,1.313 3.104,1.521 0.302,0.208 10 false I101
*a Rear view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector


Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




b.
C210421C11
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.271,1.385 2.271,1.385 2.438,1.385 false 2.073,2.563 2.229,2.969 2.229,2.969 2.375,2.969 false 0.104,0.083 0.948,0.417 0.844,0.333 10 false *1 1.625,0.76 1.927,0.938 0.302,0.177 10 false I39 2.49,1.302 2.896,1.479 0.406,0.177 10 false CANH 2.448,2.885 2.833,3.063 0.385,0.177 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

6.CHECK CAN NO.1 JUNCTION CONNECTOR (CAN NO.2 J/C - CAN NO.1 J/C)

NG

REPLACE CAN NO. 2 JUNCTION CONNECTOR

6.CHECK CAN NO.1 JUNCTION CONNECTOR (CAN NO.2 J/C - CAN NO.1 J/C)
a.

Reconnect the CAN main bus line connector (I101) to the CAN No. 2 junction connector.


b.
C247984C01
2.719,1.375 3.177,1.656 0.458,0.281 2.875,2.146 2.417,1.854 2.417,1.854 2.167,1.854 false 2.875,2.365 2.875,2.698 2.875,2.698 2.198,2.698 false 2.74,2.219 2.438,2.083 2.438,2.083 2.302,2.083 false 2.813,2.333 2.365,2.333 false 0.094,0.094 0.375,0.302 0.281,0.208 10 false *a 1.635,1.781 2.281,2 0.646,0.219 10 false CANH*b 1.667,2.625 2.313,2.844 0.646,0.219 10 false CANL*b 2.854,1.427 3.146,1.594 0.292,0.167 10 false I93 2.177,2.01 2.313,2.198 0.135,0.188 10 false B 2.208,2.26 2.385,2.448 0.177,0.188 10 false W
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 2 Junction Connector


Disconnect the CAN main bus line connector (I93) from the CAN No. 1 junction connector.

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




c.
C210421C12
1.5,0.698 1.938,1 0.438,0.302 2.073,1.865 2.219,1.396 2.219,1.396 2.385,1.396 false 2.083,2.573 2.24,2.958 2.24,2.958 2.385,2.958 false 0.083,0.125 0.927,0.458 0.844,0.333 10 *1 1.615,0.76 1.917,0.938 0.302,0.177 10 I39 2.438,1.323 2.844,1.5 0.406,0.177 10 CANH 2.427,2.875 2.813,3.052 0.385,0.177 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN BUS MAIN LINES (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)

7.CHECK FOR SHORT IN CAN BUS LINES (ECM)
a.

Reconnect the ECM main bus line connector (I104) to the CAN No. 1 junction connector.


b.

Disconnect the ECM connector.


c.
C210421C09
1.5,0.688 1.938,0.99 0.438,0.302 2.073,1.865 2.229,1.385 2.229,1.385 2.448,1.385 false 2.052,2.563 2.219,3.021 2.219,3.021 2.396,3.021 false 0.104,0.115 0.948,0.448 0.844,0.333 10 *1 1.615,0.76 1.917,0.938 0.302,0.177 10 I39 2.521,1.302 2.927,1.479 0.406,0.177 10 CANH 2.448,2.948 2.833,3.125 0.385,0.177 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG


HINT:
·

Measure the resistance with the combination meter assembly main bus line connector (I94) disconnected.

·

If the resistance changes to 1 MΩ or more when the connector is disconnected, there may be a short in the ECM.




OK

NG

REPAIR OR REPLACE CAN BUS MAIN LINES (ECM MAIN LINES)

8.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY)
a.

Reconnect the combination meter assembly main bus line connector (I94) to the CAN No. 2 junction connector.


b.

Disconnect the combination meter assembly connector.


c.
C210421C09
1.5,0.688 1.938,0.99 0.438,0.302 2.073,1.865 2.229,1.385 2.229,1.385 2.448,1.385 false 2.052,2.563 2.219,3.021 2.219,3.021 2.396,3.021 false 0.104,0.115 0.948,0.448 0.844,0.333 10 *1 1.615,0.76 1.917,0.938 0.302,0.177 10 I39 2.521,1.302 2.927,1.479 0.406,0.177 10 CANH 2.448,2.948 2.833,3.125 0.385,0.177 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


HINT:

If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN LINES (COMBINATION METER ASSEMBLY MAIN LINES)

9.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
a.

Reconnect the connector for the short-circuited branch line to the CAN J/C (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).


b.

Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C210421C13
1.5,0.698 1.938,1 0.438,0.302 2.073,1.865 2.438,1.313 false 2.083,2.583 2.417,2.917 false 0.094,0.115 0.938,0.448 0.844,0.333 10 *1 1.615,0.76 1.917,0.938 0.302,0.177 10 I39 2.458,1.115 2.865,1.292 0.406,0.177 10 CANH 2.49,2.938 2.875,3.115 0.385,0.177 10 CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR