Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.10–2014.05
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module (Network Gateway ECU)  


DESCRIPTION

·

The network gateway ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 2.

·

When the network gateway ECU receives a response signal from the ECUs connected to sub bus 2, the network gateway ECU recognizes and memorizes that the ECU is connected to sub bus 2. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to sub bus 2 when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 2, the network gateway ECU determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U1002 Lost Communication with Gateway Module (Network Gateway ECU) Network gateway ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 2.
·

Open or short in sub bus 2 main line or connector

·

Open or short in sub bus 2 branch line or connector

·

Network gateway ECU

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH

·

Open or short in CAN No. 5 junction connector

·

Open or short in CAN No. 6 junction connector

·

Open or short in CAN No. 7 junction connector


The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.

HINT:

This diagnosis procedure is for when DTC U1002 is output by the network gateway ECU (Intelligent tester display: Gateway).


WIRING DIAGRAM

C248165E02
5.302,0.521 6.51,0.708 1.208,0.188 10 false x: Suspected Area 1.146,0.531 2.604,0.719 1.458,0.188 10 false Network Gateway ECU 3.458,0.281 3.875,0.469 0.417,0.188 10 false 120 Ω 5.771,3.313 6.99,3.688 1.219,0.375 10 false Blind Spot Monitor Sensor RH 3.406,7.375 3.823,7.563 0.417,0.188 10 false 120 Ω 4.656,5.292 6.625,5.479 1.969,0.188 10 false CAN No. 6 Junction Connector 4.917,7 6.865,7.188 1.948,0.188 10 false CAN No. 7 Junction Connector 0.844,2.771 2.833,2.958 1.99,0.188 10 false CAN No. 5 Junction Connector 3.646,7.958 5.365,8.146 1.719,0.188 10 false : CAN Branch Line (CANH) 3.646,8.365 5.365,8.552 1.719,0.188 10 false : CAN Branch Line (CANL) 0.979,7.958 2.896,8.146 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.979,8.365 2.896,8.552 1.917,0.188 10 false : CAN Main Bus Line (CANL) 2.74,0.917 3.125,1.083 0.385,0.167 10 false CA2L 1,4.979 1.385,5.146 0.385,0.167 10 false CA1P 1,5.552 1.385,5.719 0.385,0.167 10 false CA1N 5.458,3.313 5.771,3.479 0.313,0.167 10 false O28 0.354,5.823 1.531,6.177 1.177,0.354 10 false Blind Spot Monitor Sensor LH 0.073,5.823 0.375,5.99 0.302,0.167 10 false T16 2.99,1.125 3.198,1.292 0.208,0.167 10 false 12 1.469,4.979 1.677,5.146 0.208,0.167 10 false 8 1.469,5.552 1.677,5.719 0.208,0.167 10 false 4 2.99,2.083 3.198,2.25 0.208,0.167 10 false 22 4,2.083 4.208,2.25 0.208,0.167 10 false 11 4.344,2.458 4.552,2.625 0.208,0.167 10 false 9 4.344,3.021 4.552,3.188 0.208,0.167 10 false 20 2.677,4.979 2.885,5.146 0.208,0.167 10 false 10 1.979,4.927 2.188,5.094 0.208,0.167 10 false R 1.979,5.583 2.188,5.75 0.208,0.167 10 false B 2.677,5.552 2.885,5.719 0.208,0.167 10 false 21 2.896,1.333 3.104,1.5 0.208,0.167 10 false LG 5.063,2.406 5.271,2.573 0.208,0.167 10 false R 5.063,3.094 5.271,3.26 0.208,0.167 10 false B 4.063,1.333 4.271,1.5 0.208,0.167 10 false G 2.99,1.677 3.104,1.844 0.115,0.167 10 false B 4.063,1.677 4.229,1.844 0.167,0.167 10 false V 4.01,1.125 4.219,1.292 0.208,0.167 10 false 13 5.573,2.458 5.781,2.625 0.208,0.167 10 false 8 5.583,3.021 5.792,3.188 0.208,0.167 10 false 4 0.792,0.531 1.094,0.698 0.302,0.167 10 false I160 4.021,0.917 4.406,1.083 0.385,0.167 10 false CA2H 5.76,2.438 6.198,2.604 0.438,0.167 10 false CA1P 5.76,3.052 6.198,3.219 0.438,0.167 10 false CA1N 4.01,6.521 4.219,6.688 0.208,0.167 10 false 3 3.052,6.521 3.26,6.688 0.208,0.167 10 false 2 3.01,6.344 3.219,6.51 0.208,0.167 10 false B 4.042,6.344 4.25,6.51 0.208,0.167 10 false L 2.99,5.969 3.198,6.135 0.208,0.167 10 false 20 4.01,5.969 4.219,6.135 0.208,0.167 10 false 9 2.99,4.521 3.198,4.688 0.208,0.167 10 false 22 4.01,4.521 4.229,4.688 0.219,0.167 10 false 11 4.01,3.563 4.219,3.729 0.208,0.167 10 false 10 2.99,3.563 3.198,3.729 0.208,0.167 10 false 21 3,4.083 3.208,4.25 0.208,0.167 10 false B 4.042,4.083 4.25,4.25 0.208,0.167 10 false G 2.729,6.719 3.167,6.885 0.438,0.167 10 false CANL 4.031,6.729 4.469,6.896 0.438,0.167 10 false CANH 0.521,2.771 0.833,2.938 0.313,0.167 10 false O31 4.385,5.292 4.698,5.458 0.313,0.167 10 false T17 4.625,7 4.938,7.167 0.313,0.167 10 false T18 0.135,0.083 2.104,0.333 1.969,0.25 12 false Sub Bus 2 (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 22 seconds, and then drive the vehicle at a speed of 5 km/h (3 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK SUB BUS 2
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C238893C06
1.51,0.677 1.99,0.969 0.479,0.292 1.656,1.667 1.938,2.135 1.938,2.135 2.198,2.135 false 1.552,1.677 1.292,2.146 1.292,2.146 1.031,2.146 false 2.042,1.51 2.406,0.813 2.406,0.813 2.646,0.813 false 1.385,1.51 1.042,0.823 1.042,0.823 0.802,0.823 false 0.063,0.031 0.26,0.208 0.198,0.177 10 false *a 0.656,2.063 1.448,2.271 0.792,0.208 10 false CA2H 2.229,2.052 2.885,2.25 0.656,0.198 10 false CA2L 2.698,0.74 3.375,0.927 0.677,0.188 10 false BATT 0.49,0.76 1.198,0.979 0.708,0.219 10 false GND 1.604,0.74 1.958,0.938 0.354,0.198 10 false I160
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in a main bus line
I160-13 (CA2H) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I160-12 (CA2L) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I160-13 (CA2H) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I160-12 (CA2L) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

2.CHECK FOR DTC OUTPUT

B

3.CHECK FOR OPEN IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)

C

7.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)

D

12.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 5 J/C)
2.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Clear the DTCs.


f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON and recheck for DTCs.

Body Electrical > Gateway > Trouble Codes
50001 150

Result:
Result Proceed to
U1002 is output from network gateway ECU
(Intelligent tester display: Gateway)
A
Other DTC is output B



A

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

3.CHECK FOR OPEN IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
a.
C238892C39
0.479,1.146 0.865,1.365 0.385,0.219 1.844,1.51 1.844,1.792 1.844,1.792 1.667,1.792 false 1.958,1.51 1.958,1.802 1.958,1.802 2.156,1.802 false 0.115,0 0.365,0.24 0.25,0.24 10 false *a 2.188,1.74 2.896,1.938 0.708,0.198 10 false CA2H 1.313,1.74 2.021,1.917 0.708,0.177 10 false CA2L 0.542,1.167 0.823,1.365 0.281,0.198 10 false I160
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

4.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 5 J/C)
4.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 5 J/C)
a.

Reconnect the network gateway ECU connector.


b.

Disconnect the wire harness connector from the CAN No. 5 junction connector.


c.
C238890C27
0.469,1.24 0.958,1.5 0.49,0.26 2.531,0.51 2.208,0.51 2.208,0.51 2.208,1.354 false 2.646,0.771 2.323,0.771 2.323,0.771 2.323,1.354 false 2.646,1.885 2.323,1.885 2.323,1.885 2.323,1.573 false 2.052,2.063 2.208,2.063 2.208,2.063 2.208,1.573 false 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.573,0.427 3.125,0.583 0.552,0.156 10 false CANH*b 2.677,0.688 3.229,0.844 0.552,0.156 10 false CANH*c 1.396,1.958 1.948,2.115 0.552,0.156 10 false CANL*b 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*c 0.552,1.281 0.833,1.479 0.281,0.198 10 false O31
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 6 Junction Connector
*c to Network Gateway ECU


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O31-10 (CANH) - O31-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
O31-11 (CANH) - O31-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to Network Gateway ECU main bus line) B
NG (to CAN No. 6 junction connector main bus line) C



A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 J/C - NETWORK GATEWAY ECU)

C

5.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 6 J/C)
5.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 6 J/C)
a.

Reconnect the wire harness connector to the CAN No. 5 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 6 junction connector.


c.
C238890C28
0.479,1.188 0.958,1.438 0.479,0.25 2.417,0.521 2.094,0.521 2.094,0.521 2.094,1.365 false 2.646,0.771 2.323,0.771 2.323,0.771 2.323,1.354 false 2.646,1.885 2.323,1.885 2.323,1.885 2.323,1.573 false 1.938,2.063 2.094,2.063 2.094,2.063 2.094,1.573 false 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 2.448,0.427 3,0.583 0.552,0.156 10 false CANH*b 2.677,0.688 3.229,0.844 0.552,0.156 10 false CANH*c 1.281,1.958 1.833,2.115 0.552,0.156 10 false CANL*b 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*c 0.573,1.229 0.854,1.438 0.281,0.208 10 false T17
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
*c to CAN No. 5 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T17-9 (CANH) - T17-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
T17-11 (CANH) - T17-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to CAN No. 5 junction connector main bus line) B
NG (to CAN No. 7 junction connector main bus line) C



A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 J/C - CAN NO. 6 J/C)

C

6.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 7 J/C)
6.CHECK FOR OPEN IN SUB BUS 2 LINES (CAN NO. 7 J/C)
a.

Reconnect the wire harness connector to the CAN No. 6 junction connector.


b.

Disconnect the instrument panel wire from the CAN No. 7 junction connector.


c.
C183982C14
1.781,2.063 2.198,2.302 0.417,0.24 0.948,0.844 0.646,0.844 0.646,0.844 0.646,2.177 false 1.24,1.177 0.938,1.177 0.938,1.177 0.938,2.167 false 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 1,0.75 1.573,0.906 0.573,0.156 10 false CANH*b 1.292,1.094 1.854,1.25 0.563,0.156 10 false CANL*b 1.844,2.094 2.115,2.26 0.271,0.167 10 false T18
*a Rear view of wire harness connector
(to CAN No. 7 Junction Connector)
*b to CAN No. 6 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T18-3 (CANH) - T18-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 6 J/C - CAN NO. 7 J/C)

7.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
a.
C238892C39
0.479,1.146 0.865,1.365 0.385,0.219 1.844,1.51 1.844,1.792 1.844,1.792 1.667,1.792 false 1.958,1.51 1.958,1.802 1.958,1.802 2.156,1.802 false 0.115,0 0.365,0.24 0.25,0.24 10 false *a 2.188,1.74 2.896,1.938 0.708,0.198 10 false CA2H 1.313,1.74 2.021,1.917 0.708,0.177 10 false CA2L 0.542,1.167 0.823,1.365 0.281,0.198 10 false I160
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

8.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 5 J/C)
8.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 5 J/C)
a.

Reconnect the network gateway ECU connector.


b.

Disconnect the wire harness connector from the CAN No. 5 junction connector.


c.
C238890C29
0.542,1.177 0.948,1.417 0.406,0.24 2.531,0.51 2.208,0.51 2.208,0.51 2.208,1.354 false 2.646,0.771 2.323,0.771 2.323,0.771 2.323,1.354 false 2.646,1.885 2.323,1.885 2.323,1.885 2.323,1.573 false 2.052,2.063 2.208,2.063 2.208,2.063 2.208,1.573 false 2.094,1.354 2.094,0.479 2.094,0.479 1.438,0.479 false 2.094,1.573 2.094,1.865 2.094,1.865 1.313,1.865 false 0.177,0.156 0.323,0.313 0.146,0.156 10 false *a 0.75,0.396 1.302,0.552 0.552,0.156 10 false CANH*b 2.563,0.427 3.115,0.583 0.552,0.156 10 false CANH*c 0.635,1.781 1.188,1.938 0.552,0.156 10 false CANL*b 1.375,1.958 1.927,2.115 0.552,0.156 10 false CANL*c 2.677,1.802 3.229,1.958 0.552,0.156 10 false CANL*d 2.677,0.688 3.229,0.844 0.552,0.156 10 false CANH*d 0.583,1.208 0.896,1.417 0.313,0.208 10 false O31
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Blind Spot Monitor Sensor RH
*c to CAN No. 6 Junction Connector
*d to Network Gateway ECU


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O31-9 (CANH) - O31-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O31-10 (CANH) - O31-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
O31-11 (CANH) - O31-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to Network Gateway ECU main bus line) B
NG (to CAN No. 6 junction connector main bus line) C
NG (to Blind spot monitor sensor RH) D



A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 J/C - NETWORK GATEWAY ECU)

C

9.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 6 J/C)

D

11.CHECK FOR SHORT IN SUB BUS 2 LINES (ECUS)
9.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 6 J/C)
a.

Reconnect the wire harness connector to the CAN No. 5 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 6 junction connector.


c.
C238890C30
0.181,0.161 0.331,0.313 0.149,0.153 10 *a 0.653,0.364 1.202,0.517 0.549,0.153 10 CANH*b 2.557,0.425 3.105,0.578 0.549,0.153 10 CANH*c 2.534,0.514 2.209,0.514 2.209,0.514 2.209,1.356 false 2.648,0.771 2.323,0.771 2.323,0.771 2.323,1.356 false 2.648,1.886 2.323,1.886 2.323,1.886 2.323,1.572 false 0.62,1.793 1.169,1.945 0.549,0.153 10 CANL*b 1.395,1.963 1.943,2.116 0.549,0.153 10 CANL*c 2.057,2.058 2.209,2.058 2.209,2.058 2.209,1.572 false 2.093,1.351 2.093,0.457 2.093,0.457 1.335,0.457 false 2.096,1.571 2.096,1.885 2.096,1.885 1.295,1.885 false 2.673,1.801 3.222,1.954 0.549,0.153 10 CANL*d 2.669,0.682 3.218,0.834 0.549,0.153 10 CANH*d 0.622,1.221 0.897,1.435 0.275,0.214 10 T17 0.534,1.171 1.011,1.428 0.477,0.257
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
*c to Blind Spot Monitor Sensor LH
*d to CAN No. 5 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T17-9 (CANH) - T17-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
T17-10 (CANH) - T17-21 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
T17-11 (CANH) - T17-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to CAN No. 5 junction connector main bus line) B
NG (to CAN No. 7 junction connector main bus line) C
NG (to Blind spot monitor sensor LH) D



A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 J/C - CAN NO. 6 J/C)

C

10.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 7 J/C)

D

11.CHECK FOR SHORT IN SUB BUS 2 LINES (ECUS)
10.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN NO. 7 J/C)
a.

Reconnect the wire harness connector to the CAN No. 6 junction connector.


b.

Disconnect the wire harness connector from the CAN No. 7 junction connector.


c.
C183982C14
1.781,2.063 2.198,2.302 0.417,0.24 0.948,0.844 0.646,0.844 0.646,0.844 0.646,2.177 false 1.24,1.177 0.938,1.177 0.938,1.177 0.938,2.167 false 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 1,0.75 1.573,0.906 0.573,0.156 10 false CANH*b 1.292,1.094 1.854,1.25 0.563,0.156 10 false CANL*b 1.844,2.094 2.115,2.26 0.271,0.167 10 false T18
*a Rear view of wire harness connector
(to CAN No. 7 Junction Connector)
*b to CAN No. 6 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T18-3 (CANH) - T18-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 6 J/C - CAN NO. 7 J/C)

11.CHECK FOR SHORT IN SUB BUS 2 LINES (ECUS)
a.

Reconnect all wire harness connectors (CAN No. 5 junction connector and CAN No. 6 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C238893C07
1.479,0.677 1.958,0.969 0.479,0.292 1.646,1.667 1.927,2.219 1.927,2.219 2.188,2.219 false 1.552,1.667 1.271,2.229 1.271,2.229 1.01,2.229 false 0.146,0.01 0.344,0.188 0.198,0.177 10 false *a 0.542,2.156 0.979,2.375 0.438,0.219 10 false CA2H 2.229,2.135 2.656,2.333 0.427,0.198 10 false CA2L 1.552,0.74 1.865,0.958 0.313,0.219 10 false I160
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I160-13 (CA2H) - I160-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).

·

If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), repair or replace the short-circuited branch line or connector.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU WIRE

12.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 5 J/C)
a.

Disconnect the wire harness connector from the CAN No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C240196C07
2.052,3.771 2.417,3.979 0.365,0.208 2.542,1.469 2.906,1.677 0.365,0.208 3.438,3.615 3.146,3.083 3.146,3.083 2.938,3.083 false 4.208,4.208 4.406,4.458 4.406,4.458 4.698,4.458 false 4.021,1.698 4.271,1.552 4.271,1.552 4.427,1.552 false 4.01,1.844 4.271,1.948 4.271,1.948 4.427,1.948 false 3.906,1.854 4.365,2.292 4.365,2.292 4.594,2.292 false 3.906,1.688 4.365,1.177 4.365,1.177 4.563,1.177 false 3.802,1.688 4.125,0.865 4.125,0.865 4.74,0.865 false 3.802,1.854 4.177,2.625 4.177,2.625 4.771,2.625 false 2.24,0.604 2.531,0.896 0.292,0.292 10 false *a 2.24,2.854 2.531,3.146 0.292,0.292 10 false *1 4.781,0.771 5.49,1.01 0.708,0.24 10 false CANH*b 4.615,1.094 5.323,1.333 0.708,0.24 10 false CANH*c 4.479,1.479 5.188,1.719 0.708,0.24 10 false CANH*d 4.833,2.552 5.542,2.792 0.708,0.24 10 false CANL*b 4.646,2.219 5.354,2.458 0.708,0.24 10 false CANL*c 4.479,1.875 5.188,2.115 0.708,0.24 10 false CANL*d 2.604,1.479 2.927,1.698 0.323,0.219 10 false O31 2.146,3.781 2.5,4 0.354,0.219 10 false I39 2.698,3 2.99,3.219 0.292,0.219 10 false CG 4.781,4.385 5.156,4.594 0.375,0.208 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Blind Spot Monitor Sensor RH
*c to CAN No. 6 Junction Connector *d to Network Gateway ECU


Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
O31-9 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Blind spot monitor sensor RH
O31-20 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
O31-10 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 6 junction connector
O31-21 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
O31-11 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Network gateway ECU
O31-22 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
O31-9 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Blind spot monitor sensor RH
O31-20 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
O31-10 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 6 junction connector
O31-21 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
O31-11 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Network gateway ECU
O31-22 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to Network Gateway ECU main bus line) B
NG (to CAN No. 6 junction connector main bus line) C
NG (to Blind spot monitor sensor RH) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

13.CHECK FOR SHORT IN SUB BUS 2 LINE (NETWORK GATEWAY ECU)

C

14.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 6 J/C)

D

16.CHECK FOR SHORT IN SUB BUS 2 LINE (ECUS)
13.CHECK FOR SHORT IN SUB BUS 2 LINE (NETWORK GATEWAY ECU)
a.

Disconnect the network gateway ECU connector.


b.
C238892C40
1.154,1.804 1.543,1.961 0.389,0.156 10 CA2L 2.211,1.804 2.6,1.961 0.389,0.156 10 CA2H 0.075,0.037 0.379,0.234 0.303,0.198 10 *a 2.571,0.889 2.945,1.07 0.374,0.181 10 GND 0.333,0.561 0.734,0.738 0.401,0.177 10 BATT 0.528,1.171 0.841,1.361 0.313,0.19 10 I160 0.478,1.139 0.899,1.377 0.421,0.238 1.966,1.501 1.966,1.885 1.966,1.885 2.193,1.885 false 1.842,1.501 1.842,1.885 1.842,1.885 1.615,1.885 false 2.202,1.262 2.43,0.977 2.43,0.977 2.545,0.977 false 1.242,1.262 0.96,0.648 0.96,0.648 0.79,0.648 false
*a Front view of wire harness connector
(to Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I160-13 (CA2H) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I160-12 (CA2L) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I160-13 (CA2H) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I160-12 (CA2L) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 J/C - NETWORK GATEWAY ECU)

14.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 6 J/C)
a.

Disconnect the wire harness connector from the CAN No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C240196C08
2.052,3.771 2.417,3.979 0.365,0.208 2.542,1.469 2.906,1.677 0.365,0.208 3.438,3.604 3.146,3.073 3.146,3.073 2.927,3.073 false 4.219,4.208 4.427,4.458 4.427,4.458 4.708,4.458 false 4.01,1.708 4.26,1.563 4.26,1.563 4.417,1.563 false 4.021,1.865 4.281,1.969 4.281,1.969 4.438,1.969 false 3.906,1.865 4.365,2.302 4.365,2.302 4.583,2.302 false 3.906,1.688 4.365,1.177 4.365,1.177 4.563,1.177 false 3.802,1.698 4.125,0.875 4.125,0.875 4.74,0.875 false 3.813,1.854 4.188,2.625 4.188,2.625 4.781,2.625 false 2.24,0.604 2.531,0.896 0.292,0.292 10 false *a 2.24,2.854 2.531,3.146 0.292,0.292 10 false *1 4.802,0.771 5.51,1.01 0.708,0.24 10 false CANH*b 4.615,1.094 5.323,1.333 0.708,0.24 10 false CANH*c 4.458,1.479 5.167,1.719 0.708,0.24 10 false CANH*d 4.823,2.521 5.531,2.76 0.708,0.24 10 false CANL*b 4.646,2.229 5.354,2.469 0.708,0.24 10 false CANL*c 4.479,1.885 5.188,2.125 0.708,0.24 10 false CANL*d 2.615,1.479 2.938,1.698 0.323,0.219 10 false T17 2.146,3.781 2.5,4 0.354,0.219 10 false I39 2.708,3.01 3,3.229 0.292,0.219 10 false CG 4.781,4.385 5.156,4.594 0.375,0.208 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 7 Junction Connector
*c to Blind Spot Monitor Sensor LH *d to CAN No. 5 Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
T17-9 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 7 junction connector
T17-20 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T17-10 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short Blind spot monitor sensor LH
T17-21 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T17-11 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 5 junction connector
T17-22 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Inspection for CANL ground short
T17-9 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 7 junction connector
T17-20 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
T17-10 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short Blind spot monitor sensor LH
T17-21 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short
T17-11 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 5 junction connector
T17-22 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Inspection for CANL +B short



Result:
Result Proceed to
OK A
NG (to CAN No. 5 junction connector main bus line) B
NG (to CAN No. 7 junction connector main bus line) C
NG (to Blind spot monitor sensor LH) D


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 J/C - CAN NO. 6 J/C)

C

15.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 7 J/C)

D

16.CHECK FOR SHORT IN SUB BUS 2 LINE (ECUS)
15.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN NO. 7 J/C)
a.

Disconnect the wire harness connector from the CAN No. 7 junction connector.


b.
C274535C02
1.51,0.302 1.948,0.646 0.438,0.344 1.563,2.146 2,2.49 0.438,0.344 2.104,1.302 2.104,1.875 2.104,1.875 2.385,1.875 false 1.823,1.302 1.823,1.875 1.823,1.875 1.406,1.875 false 2.563,4.094 2.563,3.823 false 1.677,3.073 1.677,2.656 1.677,2.656 1.469,2.656 false 2.448,1.802 3.01,2.125 0.563,0.323 10 false CANH 1,1.802 1.625,2.135 0.625,0.333 10 false CANL 0.135,0.146 0.563,0.448 0.427,0.302 10 false *a 2.458,4.135 3.021,4.458 0.563,0.323 10 false BAT 1.177,2.573 1.708,2.896 0.531,0.323 10 false CG 1.604,0.396 2.063,0.708 0.458,0.313 10 false T18 1.688,2.24 2.146,2.552 0.458,0.313 10 false I39 0.188,2.479 0.615,2.781 0.427,0.302 10 false *1
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 7 Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
T18-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
T18-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T18-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
T18-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 7 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 6 J/C - CAN NO. 7 J/C)

16.CHECK FOR SHORT IN SUB BUS 2 LINE (ECUS)
a.

Reconnect all wire harness connectors (CAN No. 5 junction connector and CAN No. 6 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus line shorted to B+ or shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C238893C06
1.51,0.677 1.99,0.969 0.479,0.292 1.656,1.667 1.938,2.135 1.938,2.135 2.198,2.135 false 1.552,1.677 1.292,2.146 1.292,2.146 1.031,2.146 false 2.042,1.51 2.406,0.813 2.406,0.813 2.646,0.813 false 1.385,1.51 1.042,0.823 1.042,0.823 0.802,0.823 false 0.063,0.031 0.26,0.208 0.198,0.177 10 false *a 0.656,2.063 1.448,2.271 0.792,0.208 10 false CA2H 2.229,2.052 2.885,2.25 0.656,0.198 10 false CA2L 2.698,0.74 3.375,0.927 0.677,0.188 10 false BATT 0.49,0.76 1.198,0.979 0.708,0.219 10 false GND 1.604,0.74 1.958,0.938 0.354,0.198 10 false I160
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
I160-13 (CA2H) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I160-12 (CA2L) - I160-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I160-13 (CA2H) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I160-12 (CA2L) - I160-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.


·

If the resistance becomes abnormal when an ECU connector is reconnected, there may be a short in the ECU.




OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU WIRE