Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM19V0EQ _57 Power Source / Network _014604 NETWORKING _0074103 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in CAN Main Bus Line (LHD Models)  


DESCRIPTION

There may be an open circuit in one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
·

DLC3 branch line or connector

·

CAN main bus line or connector

·

ECM

·

Combination meter assembly

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector



This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected a CAN main bus branch.

WIRING DIAGRAM

C241660E10
4.698,7.302 5.094,7.51 0.396,0.208 10 false ECM 0.813,8.01 2.708,8.24 1.896,0.229 10 false : CAN Main Bus Line (CANH) 0.813,8.396 2.708,8.625 1.896,0.229 10 false : CAN Main Bus Line (CANL) 4.146,8 5.865,8.229 1.719,0.229 10 false : CAN Branch Line (CANH) 4.146,8.375 5.865,8.604 1.719,0.229 10 false : CAN Branch Line (CANL) 3.813,1.25 4.219,1.427 0.406,0.177 10 false CANH 2.521,1.26 2.906,1.438 0.385,0.177 10 false CANL 2.5,7.01 2.906,7.188 0.406,0.177 10 false CANL 5.385,2.698 5.792,2.875 0.406,0.177 10 false CANH 3.823,7.01 4.26,7.188 0.438,0.177 10 false CANH 5.51,2.969 5.896,3.146 0.385,0.177 10 false CANL 5.885,3.323 6.26,3.5 0.375,0.177 10 false DLC3 5.573,3.323 5.896,3.5 0.323,0.177 10 false I39 0.448,2.781 2.396,2.979 1.948,0.198 10 false CAN No. 1 Junction Connector 3.958,1.448 4.135,1.625 0.177,0.177 10 false 16 4.385,2.521 4.542,2.698 0.156,0.177 10 false 1 4.375,3.156 4.552,3.333 0.177,0.177 10 false 2 5.25,3.052 5.427,3.229 0.177,0.177 10 false 14 2.656,3.479 2.813,3.656 0.156,0.177 10 false 2 3.958,3.479 4.135,3.656 0.177,0.177 10 false 1 3.979,2.083 4.135,2.26 0.156,0.177 10 false 1 2.635,2.083 2.813,2.26 0.177,0.177 10 false 2 2.729,6.781 2.948,6.958 0.219,0.177 10 false 26 3.813,6.781 4.052,6.958 0.24,0.177 10 false 13 3.177,7.615 3.573,7.792 0.396,0.177 10 false 120 Ω 3.208,0.667 3.604,0.844 0.396,0.177 10 false 120 Ω 5.156,2.625 5.313,2.802 0.156,0.177 10 false 6 2.74,1.771 2.896,1.948 0.156,0.177 10 false W 3.813,1.76 3.969,1.938 0.156,0.177 10 false R 3.854,6.438 4.01,6.615 0.156,0.177 10 false B 2.729,3.948 2.885,4.125 0.156,0.177 10 false W 4.938,2.573 5.094,2.75 0.156,0.177 10 false L 3.823,3.948 3.979,4.125 0.156,0.177 10 false B 4.938,3.156 5.094,3.333 0.156,0.177 10 false W 2.698,6.448 2.854,6.625 0.156,0.177 10 false W 4.969,0.406 6.198,0.667 1.229,0.26 10 false x: Suspected Area 2.646,1.448 2.896,1.625 0.25,0.177 10 false 15 2.656,5.635 2.875,5.813 0.219,0.177 10 false 2 3.958,5.635 4.135,5.813 0.177,0.177 10 false 1 0.49,0.833 2.365,1.031 1.875,0.198 10 false Combination Meter Assembly 0.208,0.833 0.552,1.01 0.344,0.177 10 false I18 3.854,5.938 4.01,6.115 0.156,0.177 10 false P 2.698,5.948 2.854,6.125 0.156,0.177 10 false W 0.448,4.917 2.396,5.115 1.948,0.198 10 false CAN No. 2 Junction Connector 2.656,4.24 2.813,4.417 0.156,0.177 10 false 2 3.958,4.24 4.135,4.417 0.177,0.177 10 false 1 4.396,7.302 4.677,7.479 0.281,0.177 10 false A25 2.854,5.635 3.156,5.813 0.302,0.177 10 false I104 3.594,5.635 3.896,5.813 0.302,0.177 10 false I104 2.854,4.24 3.146,4.417 0.292,0.177 10 false I101 3.594,4.24 3.885,4.417 0.292,0.177 10 false I101 2.896,3.479 3.198,3.656 0.302,0.177 10 false I93 3.646,3.479 3.948,3.656 0.302,0.177 10 false I93 2.875,2.083 3.094,2.26 0.219,0.177 10 false I94 3.635,2.083 3.854,2.26 0.219,0.177 10 false I94 4.333,2.708 4.542,2.885 0.208,0.177 10 false I96 4.323,2.958 4.531,3.135 0.208,0.177 10 false I96

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C210421C05
1.5,0.688 1.938,0.99 0.438,0.302 2.083,2.563 2.354,2.917 2.354,2.917 2.458,2.917 false 2.063,1.875 2.302,1.26 2.302,1.26 2.417,1.26 false 0.094,0.125 0.938,0.458 0.844,0.333 10 false *1 1.615,0.76 1.917,0.938 0.302,0.177 10 false I39 2.479,1.177 2.885,1.354 0.406,0.177 10 false CANH 2.531,2.833 2.917,3.01 0.385,0.177 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Result
OK
NG



OK

2.CHECK FOR OPEN IN CAN BUS LINES (ECM - CAN NO. 2 J/C)

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR OPEN IN CAN BUS LINES (ECM - CAN NO. 2 J/C)
a.

Disconnect the ECM connector.


b.
C239823C11
0.104,1.51 0.563,1.792 0.458,0.281 2.573,1.521 2.573,0.656 2.573,0.656 2.365,0.656 false 2.583,1.625 2.948,1.625 2.948,1.625 2.948,2.406 false 0.094,0.094 0.458,0.448 0.365,0.354 10 false *a 1.958,0.583 2.51,0.781 0.552,0.198 10 false CANH 2.781,2.438 3.25,2.635 0.469,0.198 10 false CANL 0.198,1.563 0.521,1.729 0.323,0.167 10 false A25
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-13 (CANH) -A25-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

3.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN NO. 1 J/C)
3.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN NO. 1 J/C)
a.

Reconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.
E224284C13
1.229,0.531 1.719,0.823 0.49,0.292 1.365,2.156 1.365,2.51 1.365,2.51 1.552,2.51 false 1.24,2.156 1.24,2.51 1.24,2.51 1.052,2.51 false 0.083,0.083 0.365,0.365 0.281,0.281 10 false *a 1.583,2.417 2.115,2.656 0.531,0.24 10 false CANH 0.573,2.417 1.104,2.656 0.531,0.24 10 false CANL 1.375,0.594 1.656,0.771 0.281,0.177 10 false I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-16 (CANH) - I18-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 1 J/C)
4.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 1 J/C)
a.

Reconnect the combination meter assembly connector.


b.

Disconnect the CAN No. 1 junction connectors (I94 and I93).


c.
C248833C01
1.344,1.729 1.573,1.885 0.229,0.156 2.635,1.74 2.865,1.896 0.229,0.156 0.875,2.052 0.99,2.052 0.99,2.052 1.406,2.188 false 0.979,2.292 1.24,2.292 false 1.313,2.396 1.5,2.719 1.5,2.719 1.5,2.854 true 1.479,2.354 1.74,2.354 false 3.083,1.406 3.198,1.406 3.198,1.406 2.802,2.208 false 2.229,2.01 2.333,2.01 2.333,2.01 2.573,2.281 false 2.792,2.365 3.073,2.365 3.073,2.365 3.073,2.865 false 2.594,2.417 2.76,3.021 2.76,3.021 2.76,3.135 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.333,1.979 0.99,2.177 0.656,0.198 10 false CANH*b 1.448,2.896 1.76,3.052 0.313,0.156 10 false W 0.865,2.229 1.177,2.385 0.313,0.156 10 false R 1.781,2.271 2.438,2.469 0.656,0.198 10 false CANL*b 2.563,1.323 3.219,1.521 0.656,0.198 10 false CANH*c 2.906,2.896 3.427,3.156 0.521,0.26 10 false CANL*c 2.708,3.167 3.021,3.323 0.313,0.156 10 false W 2.115,1.948 2.427,2.104 0.313,0.156 10 false B 1.375,1.729 1.833,1.927 0.458,0.198 10 false I94 2.667,1.74 3.125,1.938 0.458,0.198 10 false I93
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector Rear Side)
*b to Combination Meter Assembly
*c to CAN No. 2 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I93-1 (CANH) - I93-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN No. 2 junction connector
I94-1 (CANH) - I94-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly


Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
I93 B W CAN No. 2 junction connector
I94 R W Combination meter assembly


NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.




Result:
Result Proceed to
OK A
NG (Combination meter assembly main line) B
NG (CAN No. 2 junction connector main line) C



A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - COMBINATION METER ASSEMBLY)

C

5.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 2 J/C)
5.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 2 J/C)
a.

Disconnect the CAN No.1 junction connectors (I94 and I93).


b.

Disconnect the CAN No.2 junction connectors (I101 and I104).


c.
C248834C02
0.333,1.51 0.719,1.76 0.385,0.25 2.76,1.385 3.146,1.635 0.385,0.25 0.688,2.073 0.417,2.073 false 0.771,2.177 0.927,2.438 0.927,2.438 0.927,2.635 false 2.896,1.979 2.604,1.688 2.604,1.688 2.396,1.688 false 2.75,2.063 2.417,2.063 false 2.833,2.177 2.833,2.5 2.833,2.5 2.354,2.5 false 0.927,2.021 1.177,2.021 false 0.927,2.188 1.083,2.438 1.083,2.438 1.198,2.438 false 2.938,2.188 2.938,2.875 false 1.198,1.948 1.823,2.146 0.625,0.198 10 false CANH*b 1.844,1.615 2.448,1.813 0.604,0.198 10 false CANH*c 1.219,2.354 1.802,2.552 0.583,0.198 10 false CANL*b 2.688,2.896 3.302,3.094 0.615,0.198 10 false CANL*c 0.271,2.01 0.458,2.219 0.188,0.208 10 false P 0.865,2.646 1.073,2.833 0.208,0.188 10 false W 2.292,1.99 2.448,2.167 0.156,0.177 10 false B 2.198,2.438 2.406,2.646 0.208,0.208 10 false W 0.115,0.083 0.479,0.406 0.365,0.323 10 false *a 0.396,1.552 0.688,1.802 0.292,0.25 10 false I104 2.823,1.427 3.125,1.656 0.302,0.229 10 false I101
*a Rear view of wire harness connector
(to CAN No.2 junction Connector)
*b to ECM
*c to CAN No.1 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I104-1 (CANH) - I104-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
I101-1 (CANH) - I101-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN NO.1 junction connector


Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
I104 P W ECM
I101 B W CAN NO.1 junction connector


NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.




Result:
Result Proceed to
OK A
NG (CAN No.1 junction connector main line) B
NG (ECM main line) C



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - ECM)