There may be an open circuit in one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher. | ·
DLC3 branch line or connector ·
CAN main bus line or connector ·
ECM ·
Combination meter assembly ·
CAN No. 1 junction connector ·
CAN No. 2 junction connector |
This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected a CAN main bus branch.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.
After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
Disconnect the cable from the negative (-) battery terminal.
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A25-13 (CANH) -A25-26 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the ECM connector.
Disconnect the combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I18-16 (CANH) - I18-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the combination meter assembly connector.
Disconnect the CAN No. 2 junction connectors (I101 and I94).
| *a | Rear view of wire harness connector
(to CAN No. 2 Junction Connector Rear Side) |
| *b | to Combination Meter Assembly |
| *c | to CAN No. 1 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| I94-1 (CANH) - I94-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| I101-1 (CANH) - I101-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN No. 1 junction connector |
| Code | Color (CANH Side) | Color (CANL Side) | Connected to |
|---|---|---|---|
| I94 | R | W | Combination meter assembly |
| I101 | B | W | CAN No. 1 junction connector |
Before disconnecting the connectors, make a note of where they are connected.
Reconnect each connector to its original position.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Combination meter assembly main line) | B |
| NG (CAN No. 1 junction connector main line) | C |
A
B
C
Reconnect the CAN No.2 junction connectors (I101 and I94).
Disconnect the CAN No.1 junction connectors (I93 and I104).
| *a | Rear view of wire harness connector
(to CAN No. 1 Junction Connector) |
| *b | to CAN No. 2 Junction Connector |
| *c | to ECM |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| I104-1 (CANH) - I104-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| I93-1 (CANH) - I93-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | CAN NO.2 junction connector |
| Code | Color (CANH Side) | Color (CANL Side) | Connected to |
|---|---|---|---|
| I104 | G | W | ECM |
| I93 | B | W | CAN NO.2 junction connector |
Before disconnecting the connectors, make a note of where they are connected.
Reconnect each connector to its original position.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (CAN No.2 junction connector main line) | B |
| NG (ECM main line) | C |
A
B
C