Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)
RM19V0EQ _58 Vehicle Interior _014605 DOOR LOCK _0074106 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) D

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  DIAGNOSIS SYSTEM  


DESCRIPTION


The ECU stores trouble codes when malfunctions occur.

The diagnostic system allows for reading of the trouble codes from the DLC3.

Use the intelligent tester to help diagnose and repair the problem.



INSPECT BATTERY VOLTAGE


a.

Measure the vehicle battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the vehicle battery.



SELF-DIAGNOSTIC MODE (USING INTELLIGENT TESTER)


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Utility / Wireless Door Lock Diagnosis Mode.

Body Electrical > Main Body > Utility
Tester Display
Wireless Door Lock Diagnosis Mode
50005 123 2164

e.

Proceed to the next step in accordance with the prompts on the intelligent tester screen.

HINT:

The electrical key transmitter sub-assembly uses 2 different frequencies alternately for communication. When in self diagnostic mode, one of the channels can be selected or the channels can be automatically switched.



f.
B220865
0.115,0.031 2.385,0.323 2.271,0.292 10 Wireless Door Lock Buzzer Output: 0.625,1.385 0.854,1.531 0.229,0.146 10 ON 0.573,1.708 0.875,1.854 0.302,0.146 10 OFF 1.531,2.167 1.729,2.344 0.198,0.177 10 T1 2.146,2.167 2.344,2.344 0.198,0.177 10 T2 1.969,2.583 3.198,2.813 1.229,0.229 10 T1: 0.125 seconds 1.969,2.896 3.083,3.104 1.115,0.208 10 T2: 0.5 seconds 1.802,2.167 2,2.344 0.198,0.177 10 T1

Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer output pattern.


g.

Check the diagnostic outputs when the electrical key transmitter sub-assembly switch is held down. The diagnostic outputs can be checked by the interior light and wireless door lock buzzer patterns.

B163380
0.115,0.073 2.313,0.427 2.198,0.354 10 Wireless Door Lock Buzzer Output: 0.292,1.344 3.458,1.615 3.167,0.271 10 (Lock / Unlock / Luggage Open / Panic Switch): 0.51,1.969 0.75,2.146 0.24,0.177 10 ON 0.448,2.375 0.75,2.552 0.302,0.177 10 OFF 4.125,0.573 6.271,0.854 2.146,0.281 10 Unmatching Recognition Code (B): 4.271,1.146 4.51,1.323 0.24,0.177 10 ON 4.208,1.542 4.51,1.719 0.302,0.177 10 OFF 4.125,2.938 5.74,3.25 1.615,0.313 10 No Diagnostic Output (C): 4.177,3.375 4.479,3.552 0.302,0.177 10 OFF 1.25,2.813 1.458,2.969 0.208,0.156 10 T1 1.76,2.813 1.969,2.969 0.208,0.156 10 T2 4.938,2.042 6.375,2.344 1.438,0.302 10 Wave is being received 0.583,3.063 3.573,3.281 2.99,0.219 10 T1: 0.125 seconds (Wireless Door Lock Buzzer) 0.583,3.417 3.698,3.688 3.115,0.271 10 T2: 0.25 seconds (Wireless Door Lock Buzzer) 0.292,1.042 1.396,1.25 1.104,0.208 10 Normal Wave (A) 1.406,1.042 1.615,1.24 0.208,0.198 10 *1 3.823,3.75 6.979,4.479 3.156,0.729 10 *1: When either "CH1 Fixed" or "CH2 Fixed" is selected, the buzzer sounds only when it detects a frequency that matches the selected frequency

Result
Wireless Door Lock Buzzer Output Suspected Area
A Normal (No malfunction)
B Register wireless code
C Wave interference or malfunction of a related component