Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)
RM19V0EQ _58 Vehicle Interior _014605 DOOR LOCK _0074107 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System) M

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)  REGISTRATION  


CAUTION / NOTICE / HINT

HINT:
·

Register a new recognition code when replacing the door control transmitter module sub-assembly or the door control receiver.

·

Add mode is used to retain the already registered codes while registering a new recognition code. This mode is used when adding a door control transmitter module sub-assembly.

·

Rewrite mode is used to clear all the previously registered codes and register only new recognition codes. This mode is used when exchanging the door control transmitter module sub-assembly or the door control receiver with a new one.

·

Confirmation mode is used to confirm how many recognition codes have already been registered before an additional registration of a recognition code.

·

Prohibition mode is used to clear all the registered codes and cancel the wireless door lock function. Use this mode when the door control transmitter module sub-assembly is lost.

·

All of the steps in the following registration procedure must be performed in sequential order continuously.



PROCEDURE

Hide 1. REGISTRATION OF RECOGNITION CODE (USING INTELLIGENT TESTER)

a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Utility / Wireless Code Registration.

Body Electrical > Main Body > Utility
Tester Display
Wireless Code Registration
50005 123 233

e.

Press both LOCK and UNLOCK switches within 1 to 1.5 seconds.


f.

Press either switch for more than 1 second within 3 seconds.


g.

Check the response to the registration completion.

B111915
0.225,1.391 2.107,1.563 1.883,0.172 10 LOCK-UNLOCK Occurs Once 4.11,1.391 6.03,1.563 1.92,0.172 10 LOCK-UNLOCK Occurs Twice 0.345,2.788 0.77,2.962 0.425,0.174 10 LOCK 0.144,3.116 0.768,3.322 0.623,0.205 10 UNLOCK 1.287,2.502 1.469,2.677 0.183,0.175 10 T1 4.23,2.788 4.655,2.962 0.425,0.174 10 LOCK 4.03,3.116 4.653,3.322 0.623,0.206 10 UNLOCK 5.164,2.468 5.347,2.643 0.183,0.175 10 T1 5.374,2.468 5.556,2.643 0.183,0.175 10 T1 0.079,0.099 2.376,0.288 2.297,0.189 10 Response to registration completion: 4.98,3.452 6.763,3.634 1.783,0.183 10 T1: Approximately 1 second 0.21,0.61 6.941,0.992 6.73,0.382 10 Main body ECU automatically performs power door LOCK-UNLOCK operation to show whether registration has been completed correctly or not. 0.184,1.926 2.436,2.327 2.252,0.402 10 Registration of recognition code has been completed. 4.069,1.926 6.303,2.247 2.233,0.322 10 Registration of recognition code has failed.

HINT:
·

If the LOCK-UNLOCK operation occurs twice, registration of the recognition code has failed. Perform the registration procedures again from the beginning.

·

If registering another transmitter, repeat the procedures after the tester operation. All 4 recognition codes can be registered consecutively.




h.

Perform either of the following to complete registration of the recognition codes:

·

Use an intelligent tester to send a completion command.

·

Disconnect the intelligent tester.