Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM19V0EQ _58 Vehicle Interior _014605 DOOR LOCK _0074115 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69060A 1.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH

a.
B164415
1.125,3.823 1.125,3.052 1.125,3.052 1.219,3.052 false 0.594,3.823 0.594,3.052 0.594,3.052 0.688,3.052 false 0.073,0.073 0.302,0.302 0.229,0.229 10 false *a 1.781,3.906 2,4.125 0.219,0.219 10 false *c 2.292,3.906 2.521,4.094 0.229,0.188 10 false *b 0.719,2.969 0.917,3.177 0.198,0.208 10 false L 1.24,2.969 1.49,3.177 0.25,0.208 10 false UL
*a Component without harness connected
(Rear Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door lock motor.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the rear door lock with motor assembly LH.



b.
B164415
1.021,4.073 1.021,4.417 1.021,4.417 1.125,4.417 false 0.677,4.073 0.677,4.417 0.677,4.417 0.573,4.417 false 0.125,0.104 0.365,0.354 0.24,0.25 10 false *a 1.781,3.906 1.99,4.146 0.208,0.24 10 false *c 2.281,3.906 2.5,4.094 0.219,0.188 10 false *b 0.438,4.344 0.625,4.521 0.188,0.177 10 false E 1.146,4.344 1.635,4.552 0.49,0.208 10 false LSSR
*a Component without harness connected
(Rear Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly LH.



Hide 69050A 2.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH

a.
B164416
1.125,3.823 1.125,3.021 1.125,3.021 1.031,3.021 false 0.594,3.823 0.594,3.021 0.594,3.021 0.417,3.021 false 0.115,0.104 0.313,0.302 0.198,0.198 10 false *a 1.948,3.99 2.188,4.188 0.24,0.198 10 false *b 2.49,3.99 2.75,4.188 0.26,0.198 10 false *c 0.781,2.948 1.042,3.156 0.26,0.208 10 false UL 0.302,2.948 0.469,3.167 0.167,0.219 10 false L
*a Component without harness connected
(Rear Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door lock motor.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the rear door lock with motor assembly RH.



b.
B164416
0.677,4.073 0.677,4.427 0.677,4.427 0.5,4.427 false 1.031,4.073 1.031,4.427 1.031,4.427 1.229,4.427 false 0.115,0.094 0.333,0.313 0.219,0.219 10 false *a 1.948,3.99 2.146,4.188 0.198,0.198 10 false *b 2.49,3.99 2.708,4.177 0.219,0.188 10 false *c 1.25,4.354 1.719,4.552 0.469,0.198 10 false LSSR 0.365,4.354 0.573,4.531 0.208,0.177 10 false E
*a Component without harness connected
(Rear Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly RH.