Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2011.10–2016.05
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074120 SMART ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B264892E16
1.952,0.587 2.333,0.838 0.381,0.251 2.019,0.642 2.285,0.844 0.266,0.203 10 A43 3.304,0.587 3.685,0.838 0.381,0.251 3.408,0.642 3.62,0.844 0.212,0.203 10 O1 4.887,0.587 5.268,0.838 0.381,0.251 4.991,0.642 5.203,0.844 0.212,0.203 10 I78

a.

Disconnect the A43 and I78 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
A43-11 (E) - Body ground - W - Body ground Ground Always Below 1 Ω -
A43-2 (+B) - A43-11 (E) Input W - W +B power supply Always 11 to 14 V -
I78-6 (IG1D) - Body ground Output P - Body ground IG1 signal 20°C (68°F) 40.74 to 59.49 Ω IG1 Relay Monitor(Outside)
A43-9 (IG2D) - Body ground Output R - Body ground IG2 signal 20°C (68°F) Approximately 302.97 Ω IG2 Relay Monitor(Outside)
I78-4 (ACCD) - Body ground Output W - Body ground ACC signal 20°C (68°F) 81.49 to 118.98 Ω ACC Relay Monitor
A43-10 (CUTB) - A43-11 (E) Input L - W Dark current cut pin* Always 11 to 14 V -

*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 0.25 seconds. that form the detection area stops).


If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.


c.

Reconnect the A43 and I78 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
I78-5 (IG) - A43-11 (E) Input LG - W IG power supply Engine switch off → on (IG) Below 1 V → 11 to 14 V Engine Switch
I78-12 (CLG1) - A43-11 (E) Output Y - W Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
I78-13 (CG1B) - A43-11 (E) Output LG - W Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
I78-11 (CLG2) - A43-11 (E) Output Y - W Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Passenger Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
I78-10 (CG2B) - A43-11 (E) Output L*4, LG*5 - W Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
I78-3 (CLG5) - A43-11 (E) Output R - W Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
I78-2 (CG5B) - A43-11 (E) Output W - W Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
I78-20 (TSW1) - A43-11 (E) Input R - W Driver door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


Pulse generation (See waveform 6) D-Door Trigger Switch
I78-8 (TSW2) - A43-11 (E) Input V - W Front passenger door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched


Pulse generation (See waveform 6) P-Door Trigger Switch
I78-22 (SEN1) - A43-11 (E) Input LG - W Driver door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched


Pulse generation (See waveform 6) D-Door Touch Sensor
I78-23 (SEN2) - A43-11 (E) Input GR - W Front passenger door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched


Pulse generation (See waveform 6) P-Door Touch Sensor
O1-27 (TSW5) - A43-11 (E) Input G - W Luggage door opening switch assembly signal input Luggage door opening switch assembly off → on Pulse generation (See waveform 6) Tr/B-Door Unlock SW
O1-11 (CLG6) - A43-11 (E) Output W - W Output to No. 2 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
O1-10 (CG6B) - A43-11 (E) Output B - W Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) Proceed:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
O1-9 (CLG7) - A43-11 (E) Output R - W Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) Proceed:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


Pulse generation (See waveform 4) Over Head + Luggage (inside) (key diagnostic mode)
O1-8 (CG7B) - A43-11 (E) Output W - W Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) Proceed:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


Pulse generation (See waveform 4) Over Head + Luggage (inside) (key diagnostic mode)
I78-19 (POS1) - A43-11 (E) Output P*4, B*5 - W Driver door unlock sensor power source (12 V (drops when engine switch turned on (IG))) Engine switch off → on (IG) 9 to 14 V → Below 2 V -
I78-21 (POS2) - A43-11 (E) Output B*4, P*5 - W Front passenger door unlock sensor power source (12 V (drops when engine switch turned on (IG))) Engine switch off → on (IG) 9 to 14 V → Below 2 V -
O1-5 (RCO) - A43-11 (E) Output G - W Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 7) -
O1-17 (RDAM) - A43-11 (E) Input Y - W Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). Proceed:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 8) -
O1-6 (CSEL) - A43-11 (E) Output LG - W Communication channel switching circuit. Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation Key diagnostic mode
O1-2 (CLG8) - A43-11 (E) Output V - W Output to electrical key antenna (outside luggage) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Luggage door opening switch assembly off → on


Pulse generation (See waveform 5) Over Head + Luggage
or
Luggage + Luggage (key diagnostic mode)
O1-1 (CG8B) - A43-11 (E) Output P - W Output to electrical key antenna (outside luggage) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Luggage door opening switch assembly off → on


Pulse generation (See waveform 5) Over Head + Luggage
or
Luggage + Luggage (key diagnostic mode)

*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

*3: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK).

*4: for LHD

*5: for RHD



e.
B251021E03
0.177,1.01 0.76,1.396 0.583,0.385 10 false GND

Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection I78-12 (CLG1) - A43-11 (E)
I78-11 (CLG2) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).



f.
B251024E04
0.177,1.052 0.844,1.458 0.667,0.406 10 false GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection I78-12 (CLG1) - A43-11 (E)
I78-11 (CLG2) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).


Waveform 2 (Reference)
Item Content
Tester Connection I78-13 (CG1B) - A43-11 (E)
I78-10 (CG2B) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

All doors locked through wireless operation




g.
B251020C23
0.896,1.885 1.177,2.115 0.281,0.229 10 false *a 1.771,1.896 1.958,2.104 0.188,0.208 10 false *b 0.167,1.01 0.833,1.375 0.667,0.365 10 false GND
*a Door open
*b After approximately 30 seconds from when the door is closed


Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Tester Connection I78-3 (CLG5) - A43-11 (E)
I78-2 (CG5B) - A43-11 (E)
O1-11 (CLG6) - A43-11 (E)
O1-10 (CG6B) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds




h.
B282012C12
0.188,1.01 0.552,1.167 0.365,0.156 10 false GND 1.688,1.875 1.865,2.031 0.177,0.156 10 false *a 2.604,1.896 2.781,2.052 0.177,0.156 10 false *b
*a Before driver door lock sensor touched
*b After driver door lock sensor touched


Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection O1-9 (CLG7) - A43-11 (E)
O1-8 (CG7B) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Proceed:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched




i.
B265917C12
0.188,1.01 0.719,1.375 0.531,0.365 10 false GND 1.188,1.969 1.583,2.177 0.396,0.208 10 false *a
*a Engine switch off, all doors closed and luggage door opening switch assembly off → on


Using an oscilloscope, check waveform 5.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 5 (Reference)
Item Content
Tester Connection O1-2 (CLG8) - A43-11 (E)
O1-1 (CG8B) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Luggage door opening switch assembly off → on




j.
B251023C15
1.365,0.479 2.021,0.115 2.021,0.115 2.24,0.115 false 2.021,0.115 1.771,0.49 false 0.198,1.198 0.531,1.396 0.333,0.198 10 false GND 2.292,0.063 2.479,0.25 0.188,0.188 10 false *a
*a In actuality, sampling is being performed


Using an oscilloscope, check waveform 6.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 6 (Reference)
Item Content
Tester Connection I78-20 (TSW1) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched



Waveform 6 (Reference)
Item Content
Tester Connection I78-8 (TSW2) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched



Waveform 6 (Reference)
Item Content
Tester Connection I78-22 (SEN1) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched



Waveform 6 (Reference)
Item Content
Tester Connection I78-23 (SEN2) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched



Waveform 6 (Reference)
Item Content
Tester Connection O1-27 (TSW5) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Luggage door opening switch assembly off → on


k.
B251178C21
0.198,1 0.531,1.198 0.333,0.198 10 false GND 0.969,1.885 1.156,2.042 0.188,0.156 10 false *a 2.01,1.885 2.198,2.042 0.188,0.156 10 false *b
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 7.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 7 (Reference)
Item Content
Tester Connection O1-5 (RCO) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK).



l.
B251177C20
0.198,1.01 0.531,1.208 0.333,0.198 10 false GND 0.979,1.875 1.167,2.031 0.188,0.156 10 false *a 2.198,1.875 2.385,2.031 0.188,0.156 10 false *b
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 8.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 8 (Reference)
Item Content
Tester Connection O1-17 (RDAM) - A43-11 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Proceed:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK).




CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B278841C29
2.302,3.771 2.625,3.979 0.323,0.208 5.625,5.01 5.948,5.219 0.323,0.208 6.323,2.104 6.646,2.313 0.323,0.208 1.938,1.875 2.26,2.083 0.323,0.208 1.948,1.521 2.271,1.729 0.323,0.208 0.313,2.063 0.635,2.271 0.323,0.208 0.24,2.51 0.563,2.719 0.323,0.208 0.24,2.75 0.563,2.958 0.323,0.208 0.313,1.438 0.635,1.646 0.323,0.208 6.323,1.49 6.646,1.698 0.323,0.208 3.979,5.031 4.302,5.24 0.323,0.208 1.198,5.01 1.521,5.219 0.323,0.208 1.854,6.292 2.177,6.5 0.323,0.208 5.01,6.292 5.333,6.5 0.323,0.208 3.5,7.531 3.823,7.74 0.323,0.208 4.76,3.771 5.083,3.979 0.323,0.208 6.146,5.01 6.469,5.219 0.323,0.208 4.25,0.74 4.573,0.948 0.323,0.208 4.125,1.125 4.125,0.844 4.125,0.844 4.24,0.844 false 6.073,1.594 6.323,1.594 false 6.073,2.198 6.323,2.198 false 1.677,1.969 1.938,1.969 false 1.688,1.615 1.948,1.615 false 0.635,2.167 0.865,2.167 false 0.75,2.74 1.031,2.74 false 0.625,1.542 0.865,1.542 false 1.698,0.958 1.927,0.688 1.927,0.688 2.135,0.688 false 1.469,3.063 1.469,1.677 1.469,1.677 1.563,1.677 false 1.479,2.104 1.563,2.104 false 3.552,7.552 3.979,7.823 0.427,0.271 10 false MB 5.708,5.031 6.104,5.313 0.396,0.281 10 false 3E 1.271,5.031 1.656,5.313 0.385,0.281 10 false 3C 1.938,6.313 2.375,6.646 0.438,0.333 10 false 3B 5.083,6.313 5.427,6.573 0.344,0.26 10 false 3A 4.052,5.052 4.365,5.385 0.313,0.333 10 false 3D 4.833,3.792 5.198,4.094 0.365,0.302 10 false I13 2.385,3.792 2.813,4.094 0.427,0.302 10 false I12 6.396,2.115 6.688,2.344 0.292,0.229 10 false 3A 2.01,1.896 2.417,2.188 0.406,0.292 10 false I12 2.021,1.542 2.438,1.813 0.417,0.271 10 false I13 0.385,2.083 0.781,2.375 0.396,0.292 10 false 3D 0.323,2.531 0.656,2.74 0.333,0.208 10 false 3E 0.625,2.542 0.969,2.833 0.344,0.292 10 false *B 0.323,2.771 0.729,3.063 0.406,0.292 10 false 3F 0.625,2.781 1.052,3.125 0.427,0.344 10 false *C 0.385,1.458 0.74,1.708 0.354,0.25 10 false 3C 6.396,1.51 6.708,1.75 0.313,0.24 10 false 3B 5.969,5.042 6.323,5.323 0.354,0.281 10 false *B 6.229,5.031 6.563,5.333 0.333,0.302 10 false 3F 6.51,5.042 6.771,5.25 0.26,0.208 10 false *C 4.313,0.76 4.677,1.01 0.365,0.25 10 false MB 0.24,0.177 0.677,0.5 0.438,0.323 10 false *A 1.406,3.104 1.656,3.313 0.25,0.208 10 false *2 2.188,0.625 2.438,0.833 0.25,0.208 10 false *1
*A Main body ECU (multiplex network body ECU) with 2 connectors *B for LHD
*C for RHD - -
*1 Main body ECU (multiplex network body ECU) *2 2 connectors


B282096C36
2.302,3.771 2.625,3.979 0.323,0.208 5.625,5.01 5.948,5.219 0.323,0.208 6.313,2.094 6.635,2.302 0.323,0.208 2.063,2.021 2.385,2.229 0.323,0.208 2.073,1.656 2.396,1.865 0.323,0.208 0.313,2.063 0.635,2.271 0.323,0.208 0.24,2.51 0.563,2.719 0.323,0.208 0.24,2.75 0.563,2.958 0.323,0.208 0.313,1.438 0.635,1.646 0.323,0.208 6.323,1.542 6.646,1.75 0.323,0.208 3.979,5.031 4.302,5.24 0.323,0.208 1.198,5.01 1.521,5.219 0.323,0.208 1.854,6.292 2.177,6.5 0.323,0.208 5.01,6.292 5.333,6.5 0.323,0.208 3.5,7.531 3.823,7.74 0.323,0.208 4.76,3.771 5.083,3.979 0.323,0.208 6.146,5.01 6.469,5.219 0.323,0.208 4.208,0.75 4.531,0.958 0.323,0.208 4.083,1.125 4.083,0.844 4.083,0.844 4.198,0.844 false 6.063,1.635 6.313,1.635 false 6.063,2.198 6.313,2.198 false 1.813,2.115 2.063,2.115 false 1.813,1.76 2.063,1.76 false 0.635,2.167 0.865,2.167 false 0.74,2.75 1.031,2.75 false 0.625,1.531 0.865,1.531 false 1.854,0.979 2.083,0.708 2.083,0.708 2.292,0.708 false 1.583,3.083 1.583,1.479 1.583,1.479 1.688,1.479 false 1.583,1.844 1.677,1.844 false 1.583,2.188 1.688,2.188 false 3.552,7.552 4.042,7.823 0.49,0.271 10 false MB 5.708,5.031 5.938,5.208 0.229,0.177 10 false 3E 1.271,5.031 1.646,5.25 0.375,0.219 10 false 3C 1.927,6.313 2.24,6.521 0.313,0.208 10 false 3B 5.083,6.313 5.344,6.521 0.26,0.208 10 false 3A 4.052,5.052 4.438,5.25 0.385,0.198 10 false 3D 4.833,3.802 5.24,4.083 0.406,0.281 10 false I13 2.375,3.802 2.677,3.99 0.302,0.188 10 false I12 6.385,2.125 6.646,2.313 0.26,0.188 10 false 3A 2.125,2.042 2.583,2.333 0.458,0.292 10 false I12 2.156,1.688 2.51,1.948 0.354,0.26 10 false I13 0.385,2.094 0.802,2.396 0.417,0.302 10 false 3D 0.313,2.542 0.698,2.792 0.385,0.25 10 false 3E 0.625,2.542 0.865,2.708 0.24,0.167 10 false *B 0.313,2.781 0.719,3.01 0.406,0.229 10 false 3F 0.625,2.802 0.865,2.969 0.24,0.167 10 false *C 0.385,1.458 0.76,1.719 0.375,0.26 10 false 3C 6.396,1.573 6.635,1.781 0.24,0.208 10 false 3B 5.969,5.042 6.229,5.271 0.26,0.229 10 false *B 6.229,5.031 6.521,5.219 0.292,0.188 10 false 3F 6.5,5.042 6.823,5.25 0.323,0.208 10 false *C 4.271,0.781 4.635,1.021 0.365,0.24 10 false MB 0.25,0.188 0.5,0.396 0.25,0.208 10 false *A 2.344,0.646 2.688,0.948 0.344,0.302 10 false *1 1.5,3.125 1.75,3.333 0.25,0.208 10 false *2
*A Main body ECU (multiplex network body ECU) with 3 connectors *B for LHD
*C for RHD - -
*1 Main body ECU (multiplex network body ECU) *2 3 connectors


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
MB-11 (GND1) - Body ground - - Ground Always Below 1 Ω -
I12-3 (GND2) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
MB-30 (BECU) - Body ground Input - Battery power supply (for CPU) Always 11 to 14 V -
MB-31 (ALTB) - Body ground Input - Battery power supply (for indicator) Always 11 to 14 V -
MB-29 (ACC) - Body ground Input - ACC power supply Engine switch on (ACC) 11 to 14 V ACC SW
MB-32 (IG) - Body ground Input - Engine switch power supply Engine switch on (IG) 11 to 14 V IG SW

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
3C-15 (FLCY) - Body ground Input L - Body ground Front door LH courtesy light switch input Front door LH open Below 1 V FL Door Courtesy
Front door LH closed 11 to 14 V
I13-19 (FRCY) - Body ground Input Y - Body ground Front door RH courtesy light switch input Front door RH open Below 1 V FR Door Courtesy
Front door RH closed 11 to 14 V
I13-1 (LCTY) - Body ground Input LG - Body ground Rear door LH courtesy light switch input Rear door LH open Below 1 V RL Door Courtesy SW
Rear door LH closed Pulse generation (See waveform 1 or 2)
I13-6 (RCTY) - Body ground Input B - Body ground Rear door RH courtesy light switch input Rear door RH open Below 1 V RR Door Courtesy SW
Rear door RH closed Pulse generation (See waveform 1 or 2)
3C-9 (LGCY) - Body ground Input W - Body ground Luggage door courtesy light switch input Luggage compartment door open Below 1 V Luggage Courtesy SW
Engine switch off, all doors closed and luggage compartment door closed 11 to 14 V
I13-11 (L2) - Body ground Input R - Body ground Driver door key-linked lock input Driver door key cylinder in lock position Below 1 V Door Key SW-Lock
Engine switch off, all doors closed and driver door key cylinder in neutral position Pulse generation (See waveform 1 or 2)
I13-24 (UL3) - Body ground Input GR*1, Y*2 - Body ground Driver door key-linked unlock input Driver door key cylinder in unlock position Below 1 V D Door Key SW-UL
Engine switch off, all doors closed and driver door key cylinder in neutral position Pulse generation (See waveform 1 or 2)
3B-3 (ACT+) - Body ground Output W - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
3B-2 (ACT+) - Body ground Output B - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
3B-1 (ACT+) - Body ground Output L - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
3C-12 (ACT+) - Body ground Output L - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
3B-4 (ACTD) - Body ground Output GR*1, V*2 - Body ground Driver door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
3C-10 (TR+) - Body ground Output R - Body ground Driver door lock motor unlock drive output Luggage door open button of electrical key transmitter sub-assembly not pressed Below 1 V -
Luggage door open button of electrical key transmitter sub-assembly pressed 11 to 14 V
3B-8 (ACT-) - Body ground Output V*1, GR*2 - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
3C-11 (ACT-) - Body ground Output G - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
3B-9 (ACT-) - Body ground Output B - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
I13-7 (LSFL) - Body ground Input V - Body ground Front door LH unlock detection switch input Front door LH unlocked Below 1 V FL Door Lock Pos
Engine switch off, all doors closed and front door LH locked Pulse generation (See waveform 1 or 2)
I13-18 (LSFR) - Body ground Input W - Body ground Front door RH unlock detection switch input Front door RH unlocked Below 1 V FR Door Lock Pos
Engine switch off, all doors closed and front door RH locked Pulse generation (See waveform 1 or 2)
3C-17 (LSR) - Body ground Input LG - Body ground Rear door LH unlock detection switch input Rear door LH or RH unlocked Below 1 V RL-Door Lock Pos SW
Engine switch off, all doors closed and rear door LH and RH locked Pulse generation (See waveform 3 or 4)
3A-53 (LSR) - Body ground Input Y - Body ground Rear door RH unlock detection switch input Rear door RH or LH unlocked Below 1 V RR-Door Lock Pos SW
Engine switch off, all doors closed and rear door RH and LH locked Pulse generation (See waveform 3 or 4)

*1: for LHD

*2: for RHD


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


e.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection I13-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver door key cylinder in neutral position

Waveform 1 (Reference)
Item Content
Tester Connection I13-1 (LCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Rear door LH closed

Waveform 1 (Reference)
Item Content
Tester Connection I13-6 (RCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Rear door RH closed

Waveform 1 (Reference)
Item Content
Tester Connection I13-24 (UL3) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver door key cylinder in neutral position

Waveform 1 (Reference)
Item Content
Tester Connection I13-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and front door LH locked

Waveform 1 (Reference)
Item Content
Tester Connection I13-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and front door RH locked


f.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection I13-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver door key cylinder in neutral position

Waveform 2 (Reference)
Item Content
Tester Connection I13-1 (LCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Rear door LH closed

Waveform 2 (Reference)
Item Content
Tester Connection I13-6 (RCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Rear door RH closed

Waveform 2 (Reference)
Item Content
Tester Connection I13-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and front door LH locked

Waveform 2 (Reference)
Item Content
Tester Connection I13-24 (UL3) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver door key cylinder in neutral position

Waveform 2 (Reference)
Item Content
Tester Connection I13-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and front door RH locked


g.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Tester Connection 3C-17 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and rear door LH and RH locked

Waveform 3 (Reference)
Item Content
Tester Connection 3A-53 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and rear door RH and LH locked


h.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection 3C-17 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and rear door LH and RH locked

Waveform 4 (Reference)
Item Content
Tester Connection 3A-53 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and rear door RH and LH locked