Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074120 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Key Luggage Compartment Lock-in Prevention Function does not Operate  


DESCRIPTION

If the entry luggage compartment lock-in prevention function does not operate, there may be a problem with the communication between the No. 3 indoor electrical key antenna assembly (inside luggage compartment) and electrical key transmitter sub-assembly, wave interference or a malfunction in the certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B282017E18
1.031,1.823 1.469,2.063 0.438,0.24 10 false N38 1.01,2 3.688,2.667 2.677,0.667 10 false No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) 4.906,1.927 6.469,2.573 1.563,0.646 10 false Certification ECU (Smart Key ECU Assembly) 3.125,0.75 3.542,0.906 0.417,0.156 10 false CLGB 3.594,0.76 3.698,0.917 0.104,0.156 10 false 3 3.573,1.292 3.677,1.448 0.104,0.156 10 false 1 5.146,0.781 5.323,1.063 0.177,0.281 10 false 8 5.313,0.865 5.719,1.01 0.406,0.146 10 false CG7B 5.313,1.406 5.823,1.677 0.51,0.271 10 false CLG7 5.146,1.302 5.344,1.51 0.198,0.208 10 false 9 3.135,1.292 3.552,1.448 0.417,0.156 10 false CLG6 4.938,1.729 5.271,1.948 0.333,0.219 10 false O1

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the engine switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK ENTRY FUNCTION (ENTRY LUGGAGE COMPARTMENT OPEN FUNCTION)
a.

Check that the entry luggage compartment open function operates.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

Result:
Result Proceed to
Entry luggage compartment door open function operates A
Entry luggage compartment door open function does not operate B




A

2.CHECK WAVE ENVIRONMENT

B

2.CHECK WAVE ENVIRONMENT
a.
B274822C06
1.6,1.407 2.425,0.51 2.425,0.51 2.741,0.51 false 2.775,0.415 2.957,0.583 0.182,0.168 10 *a
*a Inspection Point


Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (inside luggage compartment), and check that the entry luggage compartment lock-in prevention function operates.

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the No. 3 indoor electrical key antenna assembly (inside luggage compartment), communication is not possible.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the No. 3 indoor electrical key antenna assembly (inside luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Entry functions operate normally.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

3.CHECK KEY DIAGNOSTIC MODE
3.CHECK KEY DIAGNOSTIC MODE

b.
B274822C07
1.6,1.407 2.425,0.51 2.425,0.51 2.741,0.51 false 2.775,0.415 2.957,0.583 0.182,0.168 10 *a
*a Inspection Point


Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.

i.

Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Place the key in the luggage area.

·

If the buzzer sounds, it can be determined that the No. 3 indoor electrical key antenna assembly (inside luggage compartment) is operating normally.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless door lock buzzer sounds.




Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY ANTENNA)
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 3 INDOOR ELECTRICAL KEY ANTENNA)
a.

Disconnect the O1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the N38 No. 3 indoor electrical key antenna assembly (inside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-9 (CLG7) - N38-1 (CLG6) Always Below 1 Ω
O1-8 (CG7B) - N38-3 (CLGB) Always Below 1 Ω
O1-9 (CLG7) or N38-1 (CLG6) - Body ground Always 10 kΩ or higher
O1-8 (CG7B) or N38-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the O1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the N38 No. 3 indoor electrical key antenna assembly (inside luggage compartment) connector.


c.
B282018E12
0.438,0.969 0.927,1.26 0.49,0.292 1.979,1.677 2.208,2.021 false 1.448,1.677 1.229,2.031 false 2.073,2.042 2.479,2.198 0.406,0.156 10 false CLGB 0.99,2.063 1.396,2.219 0.406,0.156 10 false CLG6 0.229,0.219 0.667,0.646 0.438,0.427 10 false *a 0.573,1.031 1.021,1.396 0.448,0.365 10 false N38 1.719,4.188 2.094,4.458 0.375,0.271 10 false *b 2.635,4.188 3,4.521 0.365,0.333 10 false *c 0.188,3.313 0.771,3.594 0.583,0.281 10 false GND 0.333,2.177 0.646,2.448 0.313,0.271 10 false *1

Measure the check for pulses according to the value(s) in the table below.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
N38-1 (CLG6) - N38-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)



Result:
Proceed to
OK
NG



OK

6.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)
a.

Replace the No. 3 indoor electrical key antenna assembly (inside luggage compartment).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)
7.CHECK NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)
a.

Check that the entry luggage compartment lock-in prevention function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry luggage compartment lock-in prevention function operates normally.



Result:
Proceed to
OK
NG



OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)