Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074120 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A6  Open in Rear Floor Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 2 indoor electrical key antenna assembly (rear floor). For the No. 2 indoor electrical key antenna assembly (rear floor) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A6 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor) (between terminals CLG6 and CLG4, or terminals CG6B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A6 Open in Rear Floor Electrical Key Oscillator Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor) (CLG6 - CLG4, CG6B - CLGB) (1 trip detection logic*).
·

Wire harness or connector

·

No. 2 indoor electrical key antenna assembly (rear floor)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in rear seat area:
·

Power source mode does not change when engine switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A6 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B274845E16
1.201,0.408 1.585,0.569 0.385,0.161 10 CLG4 1.186,0.88 1.585,1.041 0.399,0.161 10 CLGB 0.071,1.349 0.368,1.51 0.297,0.161 10 N10 1.669,0.767 1.774,0.926 0.106,0.159 10 3 1.671,0.316 1.776,0.462 0.106,0.146 10 1 5.644,0.414 6.061,0.581 0.417,0.167 10 CLG6 5.644,0.88 6.074,1.036 0.43,0.156 10 CG6B 5.644,1.345 5.822,1.509 0.178,0.164 10 E 5.337,0.226 5.51,0.384 0.172,0.158 10 11 5.337,0.701 5.523,0.867 0.185,0.166 10 10 5.337,1.159 5.532,1.321 0.195,0.162 10 11 5.293,1.345 5.566,1.507 0.274,0.162 10 A43 5.322,0.88 5.567,1.041 0.244,0.162 10 O1 5.322,0.414 5.567,0.576 0.244,0.162 10 O1 5.3,1.813 6.916,2.167 1.616,0.354 10 Certification ECU (Smart Key ECU Assembly) 0.072,1.495 2.082,1.871 2.01,0.376 10 No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the engine switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 2 indoor electrical key antenna assembly (rear floor) has an antenna coil between CLG4 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (rear floor).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INDOOR ELECTRICAL KEY ANTENNA)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INDOOR ELECTRICAL KEY ANTENNA)
a.

Disconnect the O1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the N10 No. 2 indoor electrical key antenna assembly (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-11 (CLG6) - N10-1 (CLG4) Always Below 1 Ω
O1-10 (CG6B) - N10-3 (CLGB) Always Below 1 Ω
A43-11 (E) - Body ground Always Below 1 Ω
O1-11 (CLG6) or N10-1 (CLG4) - Body ground Always 10 kΩ or higher
O1-10 (CG6B) or N10-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSENBLY)

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)
a.

Connect the O1 certification ECU (smart key ECU assembly) connector.

B271428C21
3.385,0.427 3.771,0.677 0.385,0.25 2.125,0.427 2.51,0.677 0.385,0.25 3.625,1.417 3.979,2.219 false 3.438,1.406 3.083,2.208 false 2.698,1.531 2.427,2.208 false 1.208,2.771 1.417,2.969 0.208,0.198 10 *1 0.177,0.042 0.448,0.313 0.271,0.271 10 *a 1.594,4.333 1.802,4.531 0.208,0.198 10 *b 2.896,2.229 3.458,2.5 0.563,0.271 10 CLG6 3.5,0.479 3.865,0.74 0.365,0.26 10 O1 2.198,0.469 2.552,0.719 0.354,0.25 10 A43 2.333,4.333 2.542,4.531 0.208,0.198 10 *c 3.823,2.25 4.427,2.583 0.604,0.333 10 CG6B 0.969,3.635 1.385,3.833 0.417,0.198 10 GND 2.375,2.24 2.646,2.563 0.271,0.323 10 E
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Within approximately 30 seconds from when the door is closed
*c After approximately 30 seconds from when the door is closed - -



b.

Connect the N10 No. 2 indoor electrical key antenna assembly (rear floor) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
O1-11 (CLG6) - A43-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)
O1-10 (CG6B) - A43-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO.2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSENBLY)

4.REPLACE NO.2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
a.

Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Center Floor)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A6 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)