Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074120 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage). For the electrical key antenna (outside luggage) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1.0 m (3.28 ft.) of the luggage compartment door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (between terminals CLG8 and CLG5, or terminals CG8B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB) (1 trip detection logic*).
·

Wire harness or connector

·

Electrical key antenna (outside luggage)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry unlock operation cannot be performed for luggage compartment door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B274845N25
1.198,0.417 1.583,0.573 0.385,0.156 10 false CLG5 1.188,0.896 1.583,1.052 0.396,0.156 10 false CLGB 0.073,1.354 0.365,1.51 0.292,0.156 10 false T11 1.667,0.781 1.771,0.938 0.104,0.156 10 false 2 1.667,0.323 1.771,0.469 0.104,0.146 10 false 1 5.656,0.427 6.073,0.594 0.417,0.167 10 false CLG8 5.646,0.896 6.073,1.052 0.427,0.156 10 false CG8B 5.646,1.354 5.823,1.521 0.177,0.167 10 false E 5.385,0.229 5.583,0.385 0.198,0.156 10 false 2 5.323,0.438 5.521,0.594 0.198,0.156 10 false O1 5.375,0.698 5.573,0.854 0.198,0.156 10 false 1 5.323,0.896 5.521,1.052 0.198,0.156 10 false O1 5.333,1.156 5.531,1.313 0.198,0.156 10 false 11 5.302,1.354 5.604,1.51 0.302,0.156 10 false A43 5.448,1.844 7.125,2.208 1.677,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.073,1.51 2.083,1.885 2.01,0.375 10 false Electrical Key Antenna (Outside Luggage)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the engine switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The electrical key antenna (outside luggage) has an antenna coil between CLG5 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the O1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the T11 electrical key antenna (outside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-2 (CLG8) - T11-1 (CLG5) Always Below 1 Ω
O1-1 (CG8B) - T11-2 (CLGB) Always Below 1 Ω
O1-2 (CLG8) or T11-1 (CLG5) - Body ground Always 10 kΩ or higher
O1-1 (CG8B) or T11-2 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
a.
B226391C23
1.823,1.073 2.219,0.708 2.219,0.708 2.406,0.708 false 1.583,1.073 1.198,0.708 1.198,0.708 1.01,0.708 false 2.438,0.615 2.865,0.792 0.427,0.177 10 false CLGB 0.531,0.615 1.021,0.875 0.49,0.26 10 false CLG5 0.188,0.177 0.427,0.458 0.24,0.281 10 false *a
*a Component without harness connected
(Electrical Key Antenna (Outside Luggage))


Remove the electrical key antenna (outside luggage).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (CLG5) - 2 (CLGB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A8 is not output.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)