Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074121 SMART ENTRY AND START SYSTEM(for Start Function) D

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  DTC CHECK / CLEAR  


NOTICE:

If the intelligent tester is connected to the vehicle with the engine switch off, the information stored in smart entry and start system related ECUs cannot be read. However, smart entry and start system DTCs and Data List information can be confirmed even if the engine switch is off using the method below:

·

Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins (the intelligent tester screen changes when communication begins).

·

Connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / Trouble Codes.



CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [POWER SOURCE CONTROL])


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / DTC.


e.

Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
HINT:

Refer to the intelligent tester operator's manual for further details.




CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [STARTING CONTROL])


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Starting Control / DTC.


e.

Check for DTCs.

Body Electrical > Starting Control > Trouble Codes
50001 221
HINT:

Refer to the intelligent tester operator's manual for further details.




CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [ENTRY&START])


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / DTC.


e.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Refer to the intelligent tester operator's manual for further details.




CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [POWER SOURCE CONTROL])


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / DTC / Clear.


e.

Clear the DTCs by following the directions on the intelligent tester display.

Body Electrical > Power Source Control > Clear DTCs
50002 223
HINT:

Refer to the intelligent tester operator's manual for further details.




CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [STARTING CONTROL])


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Starting Control / DTC / Clear.


e.

Clear the DTCs by following the directions on the intelligent tester display.

Body Electrical > Starting Control > Clear DTCs
50002 221
HINT:

Refer to the intelligent tester operator's manual for further details.




CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [ENTRY&START])


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / DTC / Clear.


e.

Clear the DTCs by following the directions on the intelligent tester display.

Body Electrical > Entry&Start > Clear DTCs
50002 125
HINT:

Refer to the intelligent tester operator's manual for further details.