Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074130 ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  TERMINALS OF ECU  


CHECK ENGINE SWITCH


B271001
3.49,0.229 3.867,0.462 0.377,0.233 3.578,0.273 3.898,0.436 0.321,0.163 10 I58

a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
I58-6 (AGND) - Body ground - G - Body ground Transponder key amplifier ground Always Below 1 Ω -
I58-7 (TXCT) - I58-6 (AGND) Input GR - G Immobiliser communication input Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
I58-8 (CODE) - I58-6 (AGND) Output SB - G Immobiliser communication output Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
I58-10 (VC5) - I58-6 (AGND) Input LG - G Transponder key amplifier power supply Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
I58-7 (TXCT) - I58-6 (AGND) Input GR - G Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



I58-8 (CODE) - I58-6 (AGND) Output SB - G Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with key held near engine switch* Pulse generation
(See waveform 2)
I58-10 (VC5) - I58-6 (AGND) Input LG - G Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)

If the result is not as specified, the engine switch may have a malfunction.

HINT:

*: Remove the key battery before performing this inspection.



c.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052
2.802,0.781 3.156,0.969 0.354,0.188 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection I58-7 (TXCT) - I58-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B251418
2.779,0.961 3.214,1.128 0.435,0.166 10 GND 2.784,1.454 2.965,1.62 0.18,0.166 10 *a 1.847,0.799 2.633,1.538 2.633,1.538 2.75,1.538 false
*a Key held against engine switch


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection I58-8 (CODE) - I58-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007
2.896,1.031 3.385,1.313 0.49,0.281 10 false GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection I58-10 (VC5) - I58-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B264892
1.947,0.669 2.344,0.907 0.397,0.238 2.022,0.715 2.318,0.872 0.296,0.157 10 A43 3.338,0.669 3.736,0.907 0.397,0.238 3.442,0.715 3.738,0.872 0.296,0.157 10 O1 4.87,0.669 5.267,0.907 0.397,0.238 4.974,0.715 5.27,0.872 0.296,0.157 10 I78

a.

Disconnect the A43 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
A43-2 (+B) - A43-11 (E) Input W - W +B power supply Always 11 to 14 V -
A43-10 (CUTB) - A43-11 (E) Input L - W Dark current cut pin Always 11 to 14 V -
A43-11 (E) - Body ground - W - Body ground Ground Always Below 1 Ω -


c.

Reconnect the A43 certification ECU (smart key ECU assembly) connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
I78-5 (IG) - A43-11 (E) Input LG - W Ignition power supply Engine switch off → on (IG) Below 1 V → 11 to 14 V Ignition Switch
I78-18 (IND) - A43-11 (E) Output L - W Security indicator output Engine switch off → on (IG) Pulse generation
→ Below 2 V
-
I78-9 (TXCT) - I78-24 (AGND) Output GR - G Signal output to transponder key amplifier Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


I78-7 (CODE) - I78-24 (AGND) Input SB - G Signal input from transponder key amplifier Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
I78-1 (VC5) - I78-24 (AGND) Output LG - G Transponder key amplifier power supply Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
I78-24 (AGND) - Body ground - G - Body ground Transponder key amplifier ground Always Below 1 Ω
A43-14 (EFII) - A43-11 (E) Input SB - W EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))
Engine switch off 11 to 14 V
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


A43-13 (EFIO) - A43-11 (E) Output Y - W EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to ECM)
Engine switch off Below 1 V


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
I78-9 (TXCT) - I78-24 (AGND) Output GR - G Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


I78-7 (CODE) - I78-24 (AGND) Input SB - G Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with key held near engine switch* Pulse generation
(See waveform 2)
I78-1 (VC5) - I78-24 (AGND) Output LG - G Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)
A43-14 (EFII) - A43-11 (E) Input SB - W EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 4)
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


A43-13 (EFIO) - A43-11 (E) Output Y - W EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to ECM)
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 5)

If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.

HINT:

*: Remove the key battery before performing this inspection.



f.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052
2.802,0.781 3.156,0.969 0.354,0.188 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection I78-9 (TXCT) - I78-24 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B251418
2.779,0.961 3.214,1.128 0.435,0.166 10 GND 2.784,1.454 2.965,1.62 0.18,0.166 10 *a 1.847,0.799 2.633,1.538 2.633,1.538 2.75,1.538 false
*a Key held against engine switch


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection I78-7 (CODE) - I78-24 (AGND)
Tool Setting 1 V/DIV., 200 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007
2.896,1.031 3.385,1.313 0.49,0.281 10 false GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection I78-1 (VC5) - I78-24 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


iv.

Waveform 4 (Reference)

B337754C04
0.802,1.25 1.26,1.448 0.458,0.198 10 false GND 2.719,1.333 3.177,1.531 0.458,0.198 10 false *a 2.906,1.333 3.365,1.531 0.458,0.198 10 false *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A43-14 (EFII) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


v.

Waveform 5 (Reference)

B337755C02
0.813,1.26 1.271,1.458 0.458,0.198 10 GND 3.115,1.365 3.573,1.563 0.458,0.198 10 *a 3.302,1.365 3.76,1.563 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A43-13 (EFIO) - A43-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


B118684
3.584,0.186 3.962,0.405 0.377,0.218 3.677,0.222 3.998,0.385 0.321,0.163 10 I24

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
I24-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
I24-3 (IGE) - I24-1 (GND) Input SB - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P

·

Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


I24-4 (SLP1) - I24-1 (GND) Output P - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked*1 11 to 14 V → Below 1.2 V
·

Push Start Error

·

Sensor Value


I24-6 (IG2) - I24-1 (GND) Input LG - W-B IG signal (IG2 power supply input for steering lock motor) Engine switch off → on (IG) Below 1 V → 11 to 14 V
·

B2788

·

Ignition Switch


I24-7 (B) - Body ground Output B - Body ground Constant power supply Always 11 to 14 V B2788

If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may have a malfunction.

HINT:

*1: The steering locks when any door is opened with the shift lever in P and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).



b.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C221561
0.229,0.417 1.635,0.583 1.406,0.167 1.469,1.583 2.438,1.708 0.969,0.125 2.281,0.469 2.708,0.625 0.427,0.156 2.438,1.708 2.521,1.99 2.521,1.99 2.573,1.99 false 1.635,0.417 2.75,0.177 2.75,0.177 2.917,0.177 false 2.938,0.177 2.708,0.458 false 3.042,1.583 3.417,1.729 0.375,0.146 10 false GND 2.656,1.906 3.146,2.052 0.49,0.146 10 false *b 3,0.104 3.365,0.333 0.365,0.229 10 false *a
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection I24-3 (IGE) - I24-1 (GND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P

·

Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off






CHECK ECM


A247842
2.529,0.494 2.926,0.732 0.397,0.238 2.602,0.543 2.901,0.702 0.299,0.159 10 E26 5.905,0.493 6.302,0.732 0.397,0.238 5.979,0.541 6.277,0.7 0.299,0.159 10 A25

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
E26-16 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
A25-1 (BATT) - E26-16 (E1) Input GR - BR +B power supply Always 11 to 14 V -
A25-2 (+B) - E26-16 (E1) Input P - BR +B power supply Engine switch on (IG) 11 to 14 V -
A25-3 (+B2) - E26-16 (E1) Input LG - BR +B power supply Engine switch on (IG) 11 to 14 V -
A25-29 (IMO) - E26-16 (E1) Input SB - BR Certification ECU (smart key ECU assembly) communication input Engine switch off 11 to 14 V -
A25-29 (IMO) - E26-16 (E1) Input SB - BR Certification ECU (smart key ECU assembly) communication input Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
A25-28 (IMI) - E26-16 (E1) Output Y - BR Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V -
A25-28 (IMI) - E26-16 (E1) Output Y - BR Certification ECU (smart key ECU assembly) communication output Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

a.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B337754C04
0.802,1.25 1.26,1.448 0.458,0.198 10 false GND 2.719,1.333 3.177,1.531 0.458,0.198 10 false *a 2.906,1.333 3.365,1.531 0.458,0.198 10 false *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A25-29 (IMO) - E26-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B337755C02
0.813,1.26 1.271,1.458 0.458,0.198 10 GND 3.115,1.365 3.573,1.563 0.458,0.198 10 *a 3.302,1.365 3.76,1.563 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection A25-28 (IMI) - E26-16 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected