Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074130 ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

When there are communication malfunctions between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*):
·

A malfunction in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly).

·

A matching communication code cannot be verified during communication between the ECM and certification ECU (smart key ECU assembly).


·

Certification ECU (smart key ECU assembly)

·

ECM

·

Wire harness or connector


Either condition is met:
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal depressed, the engine switch is pressed while carrying the key). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2799 -

WIRING DIAGRAM

B271006E12
1.12,2.029 2.002,2.204 0.882,0.175 10 A25 1.117,2.183 1.58,2.362 0.463,0.178 10 ECM 5.499,0.956 5.893,1.144 0.394,0.188 10 EFIO 5.499,1.414 5.893,1.601 0.394,0.188 10 EFII 1.464,0.956 1.859,1.144 0.394,0.188 10 IMI 1.433,1.425 1.827,1.613 0.394,0.188 10 IMO 1.783,0.878 2.477,1.051 0.693,0.173 10 28 1.783,1.326 2.477,1.499 0.693,0.173 10 29 5.231,0.87 5.527,1.08 0.296,0.21 10 13 5.238,1.353 5.535,1.563 0.296,0.21 10 14 5.117,1.936 5.498,2.122 0.381,0.187 10 A43 5.117,2.104 6.659,2.424 1.542,0.32 10 Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

When DTC B2799 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the A43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A25 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-14 (EFII) - A25-29 (IMO) Always Below 1 Ω
A43-13 (EFIO) - A25-28 (IMI) Always Below 1 Ω
A25-29 (IMO) - Body ground Always 10 kΩ or higher
A25-28 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REGISTER ECU COMMUNICATION ID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

NG

5.REPLACE ECM
5.REPLACE ECM
a.

Temporarily replace the ECM with a new or known good one.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)