Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.10–2015.04
RM19V0EQ _58 Vehicle Interior _014608 METER / GAUGE / DISPLAY _0074143 METER / GAUGE SYSTEM G

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 83100 1.INSPECT COMBINATION METER ASSEMBLY

a.

INSPECT SPEEDOMETER

NOTICE:
·

The meter ECU receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

·

The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform the inspection after confirming that no DTCs are output from the brake control system.

·

If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform the inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.



i.

Before starting the following inspection, check if brake control system DTCs are output.


ii.

Check the values by referring to the table below.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
Vehicle Speed
50003 105 42
Reference: km/h
Intelligent Tester Indication (km/h) Acceptable Range (km/h)
20 20.7 to 24.7
40 41.4 to 45.9
60 62.1 to 66.6
80 82.8 to 87.8
100 103.4 to 107.4
120 124.1 to 129.1
140 144.8 to 149.8
160 165.5 to 170.5
180 186.2 to 191.2
200 206.9 to 211.9
220 227.6 to 232.6
240 248.3 to 253.3



b.

INSPECT TACHOMETER

i.

Connect the intelligent tester, and start the engine.


ii.

Compare the test results with the tachometer indications.

DC 13.5 V, at 25°C (77°F)
Intelligent Tester Indication (rpm) Acceptable Range
Data in ( ) is for Reference
700 630 to 770
1000 (900 to 1100)
2000 (1850 to 2150)
3000 2800 to 3200
4000 (3800 to 4200)
5000 4800 to 5200
6000 (5750 to 6250)
7000 6700 to 7300



c.

CHECK LED ILLUMINATION (BULB CHECK)

i.

Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.

OK:
Warning or Indicator Light Specified Condition
Slip*1 Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON.
Automatic high beam*2
Blind spot monitor*3
Speed limit warning*4
ABS
Brake
ECO
SRS Warning light comes on for about 6 seconds after turning the ignition switch to ON.
Oil pressure Indicator or warning light comes on when turning the ignition switch to ON.
EPS
Charge
MIL (Check engine warning light)


·

*1: w/ VSC

·

*2: w/ Automatic High Beam System

·

*3: w/ Blind Spot Monitor System

·

*4: for LHD