Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ VSC) › 2011.10–2016.05
RM19V0EQ _58 Vehicle Interior _014610 SUPPLEMENTAL RESTRAINT SYSTEMS _0074148 AIRBAG SYSTEM(w/ VSC) D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC)  DIAGNOSIS SYSTEM  



FUNCTION OF SRS WARNING LIGHT


a.

Primary check

i.

Turn the ignition switch off. Wait for at least 2 seconds, then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and the diagnosis of the airbag system (including the seat belt pretensioners) is performed.

HINT:

If malfunctions are detected during the primary check, the SRS warning light remains on even after the primary check period of approximately 6 seconds.




b.

Constant check

i.

After the primary check, the airbag sensor assembly constantly monitors the airbag system for malfunctions.

HINT:

If malfunctions are detected during the constant check, the airbag sensor assembly functions as follows:

·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period of approximately 6 seconds after the ignition switch is turned to ON.


ii.

When the airbag system is malfunctioning:

·

The SRS warning light remains on even after the primary check period.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when turning the ignition switch from off to ON.


HINT:

The airbag sensor assembly keeps the SRS warning light on if airbags have been deployed.





SRS WARNING LIGHT CHECK


a.
C265591

Turn the ignition switch to ON, and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned to ON (constant check).

HINT:

When any of the following symptoms occur, refer to Problem Symptoms Table (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC)>PROBLEM SYMPTOMS TABLE).

·

The SRS warning light comes on occasionally after the primary check period.

·

The SRS warning light comes on, but a DTC is not output.

·

The ignition switch is turned from off to ON, but the SRS warning light does not come on.





FUNCTION OF SRS CONNECTORS


a.

The SRS connectors are located as shown in the illustration.

C241768E07
4.917,0.594 6.552,0.948 1.635,0.354 10 false Airbag Sensor Assembly 6.552,1.448 6.76,1.885 0.208,0.438 10 false 4 6.552,1.146 6.76,1.438 0.208,0.292 10 false 3 5.635,1.448 5.885,1.875 0.25,0.427 10 false 2 5.635,1.146 5.906,1.406 0.271,0.26 10 false 1 4.677,1.448 4.948,1.823 0.271,0.375 10 false 4 4.677,1.146 4.917,1.5 0.24,0.354 10 false 3 5.635,1.302 5.906,1.698 0.271,0.396 10 false A 0.469,0.844 1.521,1.281 1.052,0.438 10 false *1: for RHD 3.885,6.094 4.167,6.458 0.281,0.365 10 false 9 4.219,6.094 4.552,6.479 0.333,0.385 10 false 10 3.167,3.802 3.458,4.104 0.292,0.302 10 false 17 3.427,4.281 3.729,4.698 0.302,0.417 10 false 18 2.677,6.813 2.875,7.073 0.198,0.26 10 false 7 2.927,7.292 3.281,7.604 0.354,0.313 10 false 8 3.156,5.813 3.406,6.073 0.25,0.26 10 false 11 3.427,6.292 3.719,6.552 0.292,0.26 10 false 12 3.427,5.281 3.698,5.594 0.271,0.313 10 false 14 3.156,4.813 3.521,5.094 0.365,0.281 10 false 13 3.156,2.792 3.365,3.063 0.208,0.271 10 false 17 3.427,3.271 3.677,3.646 0.25,0.375 10 false 18 4.656,6.813 4.844,7.094 0.188,0.281 10 false 5 4.927,7.292 5.115,7.625 0.188,0.333 10 false 6 0.667,1.917 2.531,2.458 1.865,0.542 10 false Combination Meter Assembly (SRS Warning Light) 3.458,6.948 4.417,7.552 0.958,0.604 10 false Spiral Cable Sub-assembly 0.792,3.167 2.5,3.51 1.708,0.344 10 false Front Airbag Sensor LH 3.813,4.073 4.198,4.542 0.385,0.469 10 false 15 4.219,4.073 4.521,4.479 0.302,0.406 10 false 16 3.802,3.063 4.229,3.51 0.427,0.448 10 false 15 4.229,3.063 4.5,3.365 0.271,0.302 10 false 16 0.823,4.167 2.333,4.521 1.51,0.354 10 false Front Airbag Sensor RH 0.167,4.938 3.083,5.604 2.917,0.667 10 false Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib)*1 0.198,5.948 3.052,6.552 2.854,0.604 10 false Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib) 0.771,6.958 2.188,7.542 1.417,0.583 10 false Horn Button Assembly (Driver Side Squib)

C247162E06
4.885,0.573 6.49,1.042 1.604,0.469 10 false Airbag Sensor Assembly 6.531,1.417 6.781,1.823 0.25,0.406 10 false 4 6.531,1.104 6.74,1.469 0.208,0.365 10 false 3 5.604,1.417 6.031,1.74 0.427,0.323 10 false 2 5.604,1.104 5.802,1.375 0.198,0.271 10 false 1 4.667,1.417 5.115,1.781 0.448,0.365 10 false 4 4.667,1.104 4.854,1.427 0.188,0.323 10 false 3 5.604,1.26 5.917,1.583 0.313,0.323 10 false A 2.802,5.563 3.063,5.823 0.26,0.26 10 false 25 3.063,6.031 3.313,6.333 0.25,0.302 10 false 26 0.385,5.698 2.583,6.208 2.198,0.51 10 false Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH) 2.813,6.823 3.104,7.083 0.292,0.26 10 false 27 3.063,7.302 3.479,7.552 0.417,0.25 10 false 28 0.406,6.969 2.625,7.531 2.219,0.563 10 false Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH) 2.813,3.01 3.083,3.271 0.271,0.26 10 false 21 3.063,3.5 3.365,3.938 0.302,0.438 10 false 22 0.26,3.375 2.719,3.708 2.458,0.333 10 false Side No. 2 Airbag Sensor Assembly LH 2.802,4.292 3.104,4.542 0.302,0.25 10 false 23 3.063,4.76 3.354,5.104 0.292,0.344 10 false 24 0.49,4.417 2.458,4.938 1.969,0.521 10 false Front Seat Airbag Assembly LH (Side Squib LH) 2.792,1.719 3.156,1.99 0.365,0.271 10 false 19 3.063,2.25 3.354,2.615 0.292,0.365 10 false 20 0.479,2.083 2.563,2.427 2.083,0.344 10 false Side Airbag Sensor Assembly LH

C247163E07
0.833,0.479 2.438,0.865 1.604,0.385 10 false Airbag Sensor Assembly 2.542,1.281 2.927,1.698 0.385,0.417 10 false 4 2.542,0.969 2.781,1.302 0.24,0.333 10 false 3 0.604,1.271 0.802,1.51 0.198,0.24 10 false 4 0.604,0.969 0.813,1.271 0.208,0.302 10 false 3 1.573,1.271 1.854,1.781 0.281,0.51 10 false 2 1.573,0.969 1.865,1.302 0.292,0.333 10 false 1 1.573,1.125 1.823,1.479 0.25,0.354 10 false A 3.813,2.844 4.104,3.229 0.292,0.385 10 false 21 3.552,3.354 3.99,3.802 0.438,0.448 10 false 22 4.281,3.24 6.75,3.667 2.469,0.427 10 false Side No. 2 Airbag Sensor Assembly RH 3.823,1.51 4.146,1.75 0.323,0.24 10 false 19 3.552,2.063 3.979,2.396 0.427,0.333 10 false 20 4.448,1.896 6.563,2.385 2.115,0.49 10 false Side Airbag Sensor Assembly RH 3.813,5.5 4.167,5.854 0.354,0.354 10 false 25 3.552,5.99 3.833,6.26 0.281,0.271 10 false 26 4.396,5.625 6.594,6.281 2.198,0.656 10 false Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH) 3.823,6.813 4.104,7.104 0.281,0.292 10 false 27 3.563,7.313 3.958,7.563 0.396,0.25 10 false 28 4.385,6.948 6.615,7.563 2.229,0.615 10 false Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH) 3.552,4.677 3.896,5.073 0.344,0.396 10 false 24 3.813,4.177 4.063,4.5 0.25,0.323 10 false 23 4.51,4.313 6.531,4.958 2.021,0.646 10 false Front Seat Airbag Assembly RH (Side Squib RH)

Connector Type Application
Terminal Twin-lock Mechanism Connectors 2, 4, 6, 9, 10, 15
Half Connection Prevention Mechanism Connectors 6, 10
Activation Prevention Mechanism Connectors 2, 4, 5, 7, 9, 11, 13, 23, 25, 27
Connector Lock Mechanism (1) Connectors 8, 12, 14, 26, 28
Connector Position Assurance Mechanism Connectors 16, 18, 20, 22, 24
Connector Lock Mechanism (2) Connector A
Improper Connection Prevention Lock Mechanism Connector A


b.

Terminal twin-lock mechanism

C190972E05
2.438,0.094 2.052,0.094 false 2.813,0.656 2.438,0.094 false 5.708,0.094 5.573,0.094 false 5.854,0.635 5.708,0.094 false 0.729,0.01 2.083,0.188 1.354,0.177 10 Lance (Primary Lock) 1.229,1.448 2.167,1.625 0.938,0.177 10 Primary Lock 4.021,0.01 5.698,0.188 1.677,0.177 10 Spacer (Secondary Lock) 4.896,1.427 5.948,1.604 1.052,0.177 10 Secondary Lock

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461E14
1.427,1.083 1.271,1.083 false 1.531,1.417 1.427,1.083 false 1.719,0.813 1.5,0.813 false 1.833,1.375 1.719,0.813 false 2.146,0.531 1.938,0.531 false 2.354,1.333 2.146,0.531 false 3.219,0.563 3.406,0.563 false 3.01,1.208 3.219,0.563 false 3.458,0.865 3.635,0.865 false 3.198,1.313 3.458,0.865 false 5.917,0.74 5.729,0.74 false 6.063,1.156 5.917,0.74 false 1.125,0.458 1.958,0.667 0.833,0.208 10 Locking Arm 0.979,0.729 1.531,0.927 0.552,0.198 10 Stopper 0.469,1 1.323,1.25 0.854,0.25 10 Locking Part 3.448,0.5 3.885,0.688 0.438,0.188 10 Slider 3.667,0.802 4.135,0.99 0.469,0.188 10 Spring 5.177,0.646 5.76,0.833 0.583,0.188 10 Stopper 4.615,1.969 6.01,2.344 1.396,0.375 10 Rebounded by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected due to the spring force so that no continuity exists.



d.

Activation prevention mechanism

C238382E04
1.583,1.063 1.198,0.917 false 5.26,1.521 5.26,2.042 false 1.844,1.667 1.844,2.083 false 1.656,1.448 1.198,1.448 false 2.646,1.646 2.969,1.646 false 2.354,1.385 3,0.969 3,0.969 2.552,1.458 false 1.771,0.375 2.542,0.76 0.771,0.385 10 false When open 0.313,0.833 1.25,1.146 0.938,0.313 10 false Male Housing 3.042,0.885 4.167,1.219 1.125,0.333 10 false Female Terminal 0.302,1.375 1.281,1.677 0.979,0.302 10 false Male Terminal 3.01,1.573 4.125,1.875 1.115,0.302 10 false Female Housing 1.26,2.104 2.51,2.469 1.25,0.365 10 false Short Spring Plate 5.448,0.375 6.448,0.719 1,0.344 10 false When shorted 4.375,2.063 6.167,2.563 1.792,0.5 10 false Short spring plate contacting the male terminal

i.

The activation prevention mechanism is designed to create a short circuit automatically between the positive and negative terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462E03
2.521,0.344 2.021,0.198 false 2.635,0.76 2.281,0.885 false 2.469,1.24 2.271,1.323 false 4.927,0.896 5.24,0.688 false 0.531,0.115 2.01,0.292 1.479,0.177 10 Lock the locking button 1.927,0.813 2.302,0.979 0.375,0.167 10 Claw 1.792,1.25 2.281,1.417 0.49,0.167 10 Groove 5.281,0.604 6.927,1.031 1.646,0.427 10 Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector lock button engages the locking button claw to the groove on the other side connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464E04
0.854,0.198 1.021,0.198 false 0.833,1.104 0.854,0.198 false 1.052,0.479 1.219,0.479 false 0.927,1.25 1.052,0.479 false 0.729,2.292 0.958,2.292 false 0.51,1.792 0.729,2.292 false 5.635,0.781 5.469,0.781 false 5.646,1.156 5.635,0.781 false 1.063,0.125 2.271,0.354 1.208,0.229 10 Female Connector 1.26,0.406 2.094,0.656 0.833,0.25 10 Locking Part 1.0,2.219 2.042,2.469 1.042,0.25 10 Male Connector 2.958,0.302 4.542,0.573 1.583,0.271 10 Primary Lock Completed 5.073,0.302 6.844,0.573 1.771,0.271 10 Secondary Lock Completed 4.896,0.698 5.521,0.875 0.625,0.177 10 Retainer

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side and secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, they are completely engaged.



g.

Connector lock mechanism (2)

C204951E05
1.135,1.385 1.135,1.813 1.135,1.813 0.854,1.813 false 1.792,3.198 1.792,3.583 1.792,3.583 2.302,3.583 false 4.156,2.76 4.156,3.063 4.156,3.063 3.896,3.063 false 6.115,3.344 5.75,3.344 false 6.458,2.75 6.583,2.75 false 6.323,2.729 6.094,2.729 false 4.385,1.448 4.646,1.448 false 0.458,1.74 0.896,2.115 0.438,0.375 10 Lance 4.688,1.375 5.208,1.677 0.521,0.302 10 Holder 2.323,3.521 2.885,3.771 0.563,0.25 10 Retainer 5.208,3.25 5.854,3.51 0.646,0.26 10 Retainer 3.344,2.979 3.948,3.323 0.604,0.344 10 Retainer 5.667,2.656 6.146,2.969 0.479,0.313 10 Holder 6.625,2.667 7.031,2.917 0.406,0.25 10 Claw

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer to the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



h.

Improper connection prevention lock mechanism

C204952E09
5.292,0.792 5.292,0.219 5.292,0.219 5.656,0.219 false 5.292,1.167 5.292,1.875 5.292,1.875 4.604,1.875 false 4.958,3.01 4.583,3.01 false 1.104,1.479 1.104,2.396 1.104,2.396 0.948,2.396 false 1.021,1.188 1.021,0.521 1.021,0.521 1.333,0.521 false 6,0.719 6,1.031 6,1.031 5.51,1.031 false 3.958,0.073 4.573,0.448 0.615,0.375 10 Top View 0.25,2.323 0.958,2.74 0.708,0.417 10 Unlock Rib 3.917,1.781 4.604,2.333 0.688,0.552 10 Temporary Hold Lock 4.219,2.927 4.625,3.24 0.406,0.313 10 Lever 5.698,0.146 6.448,0.438 0.75,0.292 10 Unlock Rib 1.375,0.448 1.594,0.698 0.219,0.25 10 A 5.958,0.563 6.219,0.802 0.26,0.24 10 A

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the airbag sensor assembly, the unlock rib unlocks the temporary hold lock, allowing the lever to be pushed in by rotating around the axis A.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector (on the airbag sensor assembly side) of the airbag system squib circuit to prevent accidental airbag activation.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag activation.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.0197 in.)) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specially directed by the troubleshooting procedure.

·

To prevent the terminal and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C247453E01
3.094,2.677 3.469,2.156 3.469,2.156 3.063,2.365 false 2.479,2.76 2.104,3.188 2.104,3.188 2.49,2.469 false 5.021,2.458 4.583,3.198 4.583,3.198 5.031,2.781 false 5.51,2.677 5.979,2.125 5.979,2.125 5.521,2.365 false 6.229,4.542 6.313,4.177 6.313,4.177 6.375,4.177 false 4.021,4.531 4.146,4.135 4.146,4.135 4.208,4.135 false 5.417,4.49 5.417,5.25 false 3.313,4.49 3.313,5.24 false 3.875,6.344 3.792,6.344 3.792,6.344 3.667,6.688 false 3.104,6.823 3.292,7.177 3.292,7.177 3.365,7.177 false 6.594,6.344 6.5,6.344 6.5,6.344 6.385,6.688 false 5.823,6.813 6,7.167 6,7.167 6.083,7.167 false 0.167,0.073 3.531,0.375 3.365,0.302 10 false Wire harness connector (to Airbag Sensor Assembly): 1.833,1.771 2.854,2.042 1.021,0.271 10 false Before Release 4.479,1.771 5.406,2.115 0.927,0.344 10 false After Release 3.5,2.042 3.99,2.344 0.49,0.302 10 false Paper 6,2.042 6.521,2.365 0.521,0.323 10 false Paper 1.708,3.188 2.531,3.49 0.823,0.302 10 false Short Spring 4.208,3.229 5.031,3.563 0.823,0.333 10 false Short Spring 2.938,3.854 3.906,4.156 0.969,0.302 10 false Before Release 2.406,6.01 3.458,6.323 1.052,0.313 10 false Before Release 5.198,3.854 6.063,4.188 0.865,0.333 10 false After Release 5.115,6.01 6.094,6.292 0.979,0.281 10 false After Release 3.906,6.271 4.406,6.521 0.5,0.25 10 false Paper 4.25,4.063 4.656,4.344 0.406,0.281 10 false Paper 6.417,4.094 6.896,4.333 0.479,0.24 10 false Paper 3.396,7.094 4.26,7.385 0.865,0.292 10 false Short Spring 2.927,5.24 3.76,5.583 0.833,0.344 10 false Short Spring 5.021,5.26 5.875,5.594 0.854,0.333 10 false Short Spring 6.615,6.26 7.063,6.521 0.448,0.26 10 false Paper 6.125,7.083 7,7.396 0.875,0.313 10 false Short Spring 0.167,3.635 2.573,3.979 2.406,0.344 10 false Spiral Cable Sub-assembly Connector: 0.167,5.698 2.667,5.979 2.5,0.281 10 false No. 2 Instrument Panel Wire Connector: 2.906,0.417 4.354,0.76 1.448,0.344 10 false Instrument Panel Wire 1.417,0.417 2.49,0.688 1.073,0.271 10 false No. 2 Floor Wire 4.99,0.417 5.719,0.698 0.729,0.281 10 false Floor Wire 0.521,7.458 1.656,7.75 1.135,0.292 10 false : Short Spring