Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › 2011.10–2016.05
RM19V0EQ _58 Vehicle Interior _014610 SUPPLEMENTAL RESTRAINT SYSTEMS _0074155 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

w/o VSC: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o VSC)>PRECAUTION

w/ VSC: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 89174A 3.REMOVE FRONT AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the connector from the front airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

B312073C01
4.354,1 4.927,1 true 3.813,1.75 3.813,1.354 false 0.74,2.448 0.271,1.875 true 4.156,0.708 4.531,0.646 true 4.958,0.906 5.167,1.125 0.208,0.219 10 false *1 3.729,1.76 3.927,1.979 0.198,0.219 10 false *2 0.125,1.719 0.365,1.948 0.24,0.229 10 false *a 4.573,0.531 4.844,0.781 0.271,0.25 10 false (A)
*1 White Housing Lock *2 Yellow CPA
*a Connector Lock is Released - -



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




d.
B278818

Remove the bolt and front airbag sensor from the vehicle body.

NOTICE:

Loosen the bolt while holding the front airbag sensor because the front airbag sensor pin (stopper) is easily damaged.



e.

After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296255C04
4.76,1.833 5.042,2.125 0.281,0.292 10 false *b 1.396,1.833 1.667,2.156 0.271,0.323 10 false *b 4.76,0.573 5.042,0.885 0.281,0.313 10 false *a 1.396,0.573 1.688,0.865 0.292,0.292 10 false *a
*a Incorrect *b Correct