71075B
1.INSTALL BENCH TYPE REAR SEAT CUSHION COVER
Temporarily install the bench type rear seat cushion cover to the bench type rear seat cushion pad.
Using hog ring pliers, install 24 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 41 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
71078S
2.INSTALL SEPARATE TYPE REAR SEATBACK COVER (for LH Side)
Using hog ring pliers, install the separate type rear seatback cover with 8 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
3.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side)
Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.
Engage the 2 hooks.
Using hog ring pliers, install the 6 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Engage the 2 hooks to install the separate type rear seatback cover with pad.
72667
4.INSTALL REAR SEATBACK UPPER LOCK BEZEL (for LH Side)
Engage the 4 claws to install the rear seatback upper lock bezel.
73345
5.INSTALL REAR SEAT CENTER SHOULDER BELT GUIDE
Engage the guide.
Install the rear seat center shoulder belt guide to the rear seatback assembly LH with the 2 screws.
71077S
6.INSTALL SEPARATE TYPE REAR SEATBACK COVER (for RH Side)
Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 10 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Using hog ring pliers, install 7 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
7.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side)
Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly RH.
Engage the 2 hooks.
Using hog ring pliers, install the rear separate type seatback cover with pad to the seatback frame with 7 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Engage the 2 hooks to install the separate type rear seatback cover with pad.
72667
8.INSTALL REAR SEATBACK UPPER LOCK BEZEL (for RH Side)
Engage the 4 claws to install the rear seatback upper lock bezel.
72806B
9.INSTALL REAR CENTER SEAT ARMREST CUP HOLDER SUB-ASSEMBLY
Engage the 2 claws and 2 guides to install the rear center seat armrest cup holder sub-assembly.
71349C
10.INSTALL REAR SEATBACK HINGE COVER
Install the rear seatback hinge cover as shown in the illustration.
72830
11.INSTALL REAR CENTER SEAT ARMREST ASSEMBLY
Engage the 2 claws to install the bush.
Insert the guide.
Install the rear center seat armrest assembly with the bolt and washer.
72848A
12.INSTALL NO. 1 SEAT ARMREST COVER
Engage the 3 claws to install the No. 1 seat armrest cover.
73344
13.INSTALL REAR SEAT SHOULDER BELT GUIDE LH
Engage the guide.
Install the rear seat shoulder belt guide LH to the rear side seatback pad with frame LH with the 2 screws.
73343
14.INSTALL REAR SEAT SHOULDER BELT GUIDE RH
Engage the guide.
Install the rear seat shoulder belt guide RH to the rear side seatback pad with frame RH with the 2 screws.