Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM19V0EQ _58 Vehicle Interior _014611 SEAT _0074168 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY


a.

Disconnect the d11 and d12 position control ECU and switch assembly connectors.

B219505
3.816,0.29 4.071,0.428 0.255,0.138 10 d11 2.922,0.289 3.171,0.43 0.249,0.142 10 d12 2.863,0.264 3.201,0.462 0.338,0.199 3.747,0.264 4.084,0.462 0.338,0.199


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal Connection Wiring Color Terminal Description Condition Specified Condition
d11-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
d11-7 (+B) - d11-2 (GND) W - W-B Power source Always 11 to 14 V
d12-12 (SYSB) - d11-2 (GND) P - W-B System power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the d11 and d12 position control ECU and switch assembly connectors.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal Connection Wiring Color Terminal Description Condition Specified Condition
d11-6 (+B2) - d11-1 (GND2) SB - W-B Lumbar support adjuster power source Always 11 to 14 V
d11-1 (GND2) - Body ground W-B - Body ground Lumbar support adjuster ground Always Below 1 Ω
d11-3 (SLD+) - d11-2 (GND) L - W-B Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
d11-4 (SLD-) - d11-2 (GND) GR - W-B Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
d11-5 (FRV-) - d11-2 (GND) R - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
d11-8 (FRV+) - d11-2 (GND) B - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
d11-9 (RCL+) - d11-2 (GND) P - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
d11-11 (RCL-) - d11-2 (GND) LG - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
d11-10 (LFT+) - d11-2 (GND) V - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
d11-12 (LFT-) - d11-2 (GND) G - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
d12-1 (SGND) - d11-2 (GND) BR - W-B Position sensor round Always Below 1 Ω
d12-3 (SSFV) - d12-1 (SGND) R - BR Front vertical position signal Front vertical function operating 4.5 to 4.8 V
d12-4 (SSRL) - d12-1 (SGND) P - BR Lifter position signal Lifter function operating 4.5 to 4.8 V
d12-5 (SSRS) - d12-1 (SGND) G- BR Slide position signal Slide function operating 4.5 to 4.8 V
d12-11 (SSRR) - d12-1 (SGND) V - BR Reclining position signal Reclining function operating 4.5 to 4.8 V

If the result is not as specified, the position control ECU and switch assembly may have a malfunction.



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH


a.

Disconnect the J13 outer mirror control ECU assembly RH connector.

B209687
4.139,0.2 4.446,0.346 0.307,0.146 10 J13 4.097,0.168 4.41,0.376 0.313,0.209 3.091,0.2 3.356,0.346 0.265,0.146 10 z7 3.005,0.168 3.317,0.376 0.313,0.209


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
J13-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J13-14 (BDR) - J13-7 (GND) W - W-B Power source Always 11 to 14 V
J13-5 (SIG) - J13-7 (GND) BE - W-B Power source (IG) Always Below 1 V
Engine switch on (IG) 11 to 14 V
J13-6 (CPUB) - J13-7 (GND) W - W-B Power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J13 outer mirror control ECU assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
J13-3 (M2) - J13-13 (MSWE) B - V M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
J13-2 (M1) - J13-13 (MSWE) G - V M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
J13-1 (MM) - J13-13 (MSWE) P - V SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V

If the result is not as specified, the outer mirror control ECU assembly RH may have a malfunction.



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


a.

Disconnect the MB, I12 and I13 main body ECU (multiplex network body ECU) connectors.

B282096
2.188,3.771 2.51,3.979 0.323,0.208 3.865,5.01 4.188,5.219 0.323,0.208 1.083,5.01 1.406,5.219 0.323,0.208 1.74,6.292 2.063,6.5 0.323,0.208 4.885,6.292 5.208,6.5 0.323,0.208 3.375,7.531 3.698,7.74 0.323,0.208 4.646,3.771 4.969,3.979 0.323,0.208 5.823,5.021 6.146,5.229 0.323,0.208 4.042,1.125 4.042,0.844 4.042,0.844 4.156,0.844 false 1.813,1.74 2.073,1.74 false 1.813,2.094 2.073,2.094 false 1.281,2.76 1.542,2.76 false 4.198,0.76 4.729,1.083 0.531,0.323 10 false MB 3.438,7.542 3.823,7.844 0.385,0.302 10 false MB 0.906,1.51 1.292,1.75 0.385,0.24 10 false 3C 1.156,5.021 1.75,5.438 0.594,0.417 10 false 3C 5.865,1.479 6.25,1.771 0.385,0.292 10 false 3B 1.823,6.302 2.365,6.677 0.542,0.375 10 false 3B 5.865,2.156 6.302,2.448 0.438,0.292 10 false 3A 4.969,6.302 5.323,6.604 0.354,0.302 10 false 3A 0.906,2.146 1.354,2.427 0.448,0.281 10 false 3D 3.938,5.021 4.292,5.313 0.354,0.292 10 false 3D 2.125,1.677 2.615,1.969 0.49,0.292 10 false I13 4.719,3.792 5.25,4.177 0.531,0.385 10 false I13 2.125,2.031 2.646,2.396 0.521,0.365 10 false I12 2.26,3.792 2.844,4.167 0.583,0.375 10 false I12 1.594,2.688 2.104,3.073 0.51,0.385 10 false 3F 5.906,5.031 6.313,5.333 0.406,0.302 10 false 3F


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Engine switch on (IG) → off 11 to 14 V → Below 1 V
MB-29 (ACC) - Body ground - Ignition power supply (ACC signal) Engine switch on (ACC) → off 11 to 14 V → Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
I12-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
I13-19 (FRCY) - Body ground Y - Body ground Front door courtesy light switch RH input Front door RH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.