DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Mirror R / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Seat Memory Switch1 | M1 switch | ON or OFF | ON: M1 switch on
OFF: M1 switch off |
- |
| Seat Memory Switch2 | M2 switch | ON or OFF | ON: M2 switch on
OFF: M2 switch off |
- |
| Seat Memory Switch3 | M3 switch* | ON or OFF | ON: M3 switch on
OFF: M3 switch off |
Not applicable |
| Seat Memory Set SW | SET switch | ON or OFF | ON: SET switch on
OFF: SET switch off |
- |
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly | MIN: 0 V, MAX: 19.98 V | Within range from 11 to 14 V | - |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
Enter the following menus: Body / Driver Seat / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reclining Rear | Reclining switch signal (Rearward) | ON or OFF | ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off |
- |
| Reclining Front | Reclining switch signal (Forward) | ON or OFF | ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off |
- |
| Front Vertical Down | Front vertical switch signal (Downward) | ON or OFF | ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off |
- |
| Front Vertical Up | Front vertical switch signal (Upward) | ON or OFF | ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off |
- |
| Lifter Switch Down | Lifter switch signal (Downward) | ON or OFF | ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off |
- |
| Lifter Switch Up | Lifter switch signal (Upward) | ON or OFF | ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off |
- |
| Slide Rear | Slide switch signal (Rearward) | ON or OFF | ON: Slide switch (Rearward) on
OFF: Slide switch (Rearward) off |
- |
| Slide Front | Slide switch signal (Forward) | ON or OFF | ON: Slide switch (Forward) on
OFF: Slide switch (Forward) off |
- |
| Seat Memory No1 | Seat position memorized with M1 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No2 | Seat position memorized with M2 switch | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
- |
| Seat Memory No3 | Seat position memorized with M3* | Mem or Not Mem | Mem: Memorized
Not Mem: Not memorized |
Not applicable |
| Ignition Switch | Communication state of ignition switch signal | ON or OFF | ON: Ignition switch to ON signal received
OFF: Ignition switch off signal not received |
- |
| P Switch | Park state signal | ON or OFF | ON: Shift lever in P
OFF: Shift lever in a position other than P |
- |
| Parking Brake SW | Parking brake switch status | ON or OFF | ON: Parking brake applied
OFF: Parking brake released |
- |
| Vehicle Speed | Vehicle speed data | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| Power Voltage | Power supply for position control ECU and switch assembly | Min: 0.95 V, Max: 20.84 V | Within range from 11 V to 14 V | - |
| Slide Position | Seat slide position | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Reclining Position | Seat reclining position | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Front Vertical Position | Seat front vertical position | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Lifter Position | Seat lifter position | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Slide Pos Mem No1 | Seat slide position memorized with M1 switch | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Reclining Pos Mem No1 | Seat reclining position memorized with M1 switch | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Frnt Vrtcl Pos Mem No1 | Front vertical position memorized with M1 switch | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Lifter Pos Mem No1 | Lifter position memorized with M1 switch | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Slide Pos Mem No2 | Seat slide position memorized with M2 switch | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Reclining Pos Mem No2 | Seat reclining position memorized with M2 switch | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Frnt Vrtcl Pos Mem No2 | Front vertical position memorized with M2 switch | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Lifter Pos Mem No2 | Lifter position memorized with M2 switch | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Slide Pos Mem No3 | Seat slide position memorized with M3* | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Reclining Pos Mem No3 | Seat reclining position memorized with M3 switch* | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Frnt Vrtcl Pos Mem No3 | Front vertical position memorized with M3 switch* | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Lifter Pos Mem No3 | Lifter position memorized with M3 switch* | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Motor Status | State of slide motor control | STANDBY, MOVING or LOCK | STANDBY: Slide motor idle
MOVING: Slide motor moving LOCK: Slide motor locked |
- |
| Slide Position Init Flag | Seat slide limit position memory | ON or OFF | ON: Memorized
OFF: Not memorized |
- |
| Slide Position Rear Limit | Seat slide position | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | - |
| Shift P sw(PMN) | Park state signal* | ON or OFF | ON: Shift lever in P
OFF: Shift lever in a position other than P |
Not applicable |
| Memory Button Buzzer Request | Driver seat buzzer request display | OFF, MOVE, REGISTRY, CANCEL, REG NG or REG WAIT | OFF: Buzzer does not sound
MOVE: Request to sound buzzer when starting memory replay REGISTRY: Request to sound buzzer when starting memory registration CANCEL: Request to sound buzzer when canceling memory call registration REG NG: Request to sound buzzer when memory call registration not possible REG WAIT: Request to sound buzzer when starting memory call cabin scan |
- |
| Driver Seat Request Command | Driver seat operation request received | OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET | OFF: No instruction
MEMORY: Request to memorize MEM MOV: Request to recall memory MEM SOD: Request to replay RET MOV: Request to return AWY MOV: Request to move away AWY SOD: Request to recall away position memory MEM AWY: Request to recall memorized position of seatback MEM RET: Request to restore seatback to memorized position |
- |
| Driver Seat POS REQ | Seat memory switch operation value | OFF, MEM1, MEM2, MEM3*, DRV1*, DRV2* or DRV3* | OFF: No operation
MEM1: M1 switch operation status MEM2: M2 switch operation status MEM3: M3 switch operation status* DRV1: Other 1 operation status* DRV2: Other 2 operation status* DRV3: Other 3 operation status* |
- |
| Away Move Range Scale | The seat travel distance for the power easy access system* | NONE, SMALL, STANDARD or LONG | NONE: Seat travel distance none
SMALL: Seat travel distance short STANDARD: Seat travel distance normal LONG: Seat travel distance long |
Not applicable |
| Return Move | Return function* | NOT AVL or AVAIL | NOT AVL: Not available
AVAIL: Available |
Not applicable |
| Return & Away Function | Return & Away Function* | NOT AVL or AVAIL | NOT AVL: Not available
AVAIL: Available |
Not applicable |
| Driver Seat Buckle SW | Driver seat belt buckle switch* | OFF or ON | OFF: Driver seat belt unfastened
ON: Driver seat belt fastened |
Not applicable |
| Return Position | Return position* | Min: 0000, Max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Number of Trouble Codes | Number of trouble codes | Min.: 0 or Max.: 255 | Number of DTCs will be displayed | - |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock SW-Lock | Door control switch (power window regulator master switch assembly) lock signal | ON or OFF | ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed |
- |
| Door Lock SW-Unlock | Door control switch (power window regulator master switch assembly) unlock signal | ON or OFF | ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed |
- |
| FR Door Courtesy | Front door courtesy light switch assembly signal | ON or OFF | ON: Driver door open
OFF: Driver door closed |
- |
| Mem SW No. w/KeyID1 | Memory switch linked with key ID1 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1 MEM SW2: M2 switch linked with key ID1 MEM SW3: M3 switch linked with key ID1* |
- |
| Mem SW No. w/KeyID2 | Memory switch linked with key ID2 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2 MEM SW2: M2 switch linked with key ID2 MEM SW3: M3 switch linked with key ID2* |
- |
| Mem SW No. w/KeyID3 | Memory switch linked with key ID3 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3 MEM SW2: M2 switch linked with key ID3 MEM SW3: M3 switch linked with key ID3* |
- |
| Mem SW No. w/KeyID4 | Memory switch linked with key ID4 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4 MEM SW2: M2 switch linked with key ID4 MEM SW3: M3 switch linked with key ID4* |
- |
| Mem SW No. w/KeyID5 | Memory switch linked with key ID5 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5 MEM SW2: M2 switch linked with key ID5 MEM SW3: M3 switch linked with key ID5* |
- |
| Mem SW No. w/KeyID6 | Memory switch linked with key ID6 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6 MEM SW2: M2 switch linked with key ID6 MEM SW3: M3 switch linked with key ID6* |
- |
| Mem SW No. w/KeyID7 | Memory switch linked with key ID7 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7 MEM SW2: M2 switch linked with key ID7 MEM SW3: M3 switch linked with key ID7* |
- |
| Driver Seat Memory1 | Seat position memorized with M1 switch | ON or OFF | OFF: Not memorized
ON: Memorized |
- |
| Driver Seat Memory2 | Seat position memorized with M2 switch | ON or OFF | OFF: Not memorized
ON: Memorized |
- |
| Driver Seat Memory3 | Seat position memorized with M3 switch* | ON or OFF | OFF: Not memorized
ON: Memorized |
Not applicable |
*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.
ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Driver Seat / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Buzzer | Buzzer operation | OFF/ON | - |