Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM19V0EQ _58 Vehicle Interior _014613 HEATING / AIR CONDITIONING _0074197 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) D

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Air conditioning system data and the Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the intelligent tester to check for malfunctions and perform troubleshooting.




LIST OF OPERATION METHODS


a.

By operating each of the air conditioning control switches as shown in the diagram below, it is possible to enter diagnostic check mode.

E236715
4.625,5.125 5.073,5.385 0.448,0.26 3.021,5.135 3.469,5.396 0.448,0.26 2.76,6.458 3.208,6.719 0.448,0.26 1.333,4.198 1.781,4.458 0.448,0.26 1.333,5.625 1.781,5.885 0.448,0.26 0.5,7.854 0.948,8.115 0.448,0.26 1.542,0.438 4.354,1.25 2.813,0.813 10 false Turn the ignition switch to ON while pressing the air conditioning control assembly AUTO switch and Recirculation/Fresh switch simultaneously. Hold both switches until the indicator check screen appears. 4.573,1.219 6.688,1.719 2.115,0.5 10 false The AUTO and Recirculation/Fresh switches are not pressed at the same time. 2.25,2.781 3.656,3.125 1.406,0.344 10 false Indicator Check (continuous operation) 2.042,4.198 3.75,4.542 1.708,0.344 10 false Sensor Check (DTC check) (continuous operation) 2.052,5.656 3.76,6 1.708,0.344 10 false Sensor Check (DTC check) (step operation) 4.677,5.177 5.083,5.333 0.406,0.156 10 false AUTO 3.073,5.188 3.479,5.344 0.406,0.156 10 false UP Dr 2.813,6.51 3.333,6.74 0.521,0.229 10 false UP Dr 1.458,7.229 4.427,7.385 2.969,0.156 10 false Check mode is canceled and A/C control starts 1.417,4.24 1.823,4.396 0.406,0.156 10 false OFF 1.427,5.667 1.833,5.823 0.406,0.156 10 false OFF 1,7.906 2.708,8.063 1.708,0.156 10 false : Indicates switch operation 0.719,8.333 2.365,8.49 1.646,0.156 10 false OFF: Blower fan off switch 3.104,8.333 5.656,8.49 2.552,0.156 10 false UP Dr: Driver side temperature up switch 3.104,7.906 5.656,8.063 2.552,0.156 10 false AUTO: Automatic air conditioning switch



INDICATOR CHECK


a.

Turn the ignition switch off.


b.

Turn the ignition switch to ACC and wait at least 5 seconds.


c.

Turn the ignition switch to ON while pressing the air conditioning control assembly "AUTO" switch and "Recirculation/Fresh" switch simultaneously. Hold both switches until the indicator check screen appears.

E228203
0.485,0.068 0.732,0.237 0.248,0.169 10 *A 3.963,0.069 4.21,0.239 0.248,0.169 10 *B
*A for LHD *B for RHD



d.

The indicator check is automatically performed when panel diagnosis is activated. Check that the indicators light up and go off 4 times at 1 second intervals continuously.

E228204
0.408,0.091 0.731,0.25 0.323,0.159 10 *A 2.48,1.437 2.661,1.596 0.181,0.159 10 *a 2.543,1.854 2.724,2.012 0.181,0.159 10 *b 2.543,2.376 2.724,2.534 0.181,0.159 10 *c 2.984,1.516 3.165,1.674 0.181,0.159 10 *d 3.583,1.516 3.764,1.674 0.181,0.159 10 *d 3.89,0.088 4.213,0.247 0.323,0.159 10 *B
*A for LHD *B for RHD
*a Indicator Blinking Pattern *b ON
*c OFF *d 1 sec.


HINT:
·

The sensor check automatically starts when the indicator check is completed.

·

Press the "OFF" switch to cancel check mode.





SENSOR CHECK (DTC CHECK)


a.

Start the engine and warm it up.


b.

Perform the indicator check.

HINT:

After the indicator check is completed, the system enters DTC check mode automatically.



c.

Read the DTC displayed on the accessory meter display.

E228205
0.412,0.13 0.59,0.274 0.178,0.143 10 *A 1.565,0.13 1.744,0.274 0.178,0.143 10 *a 3.893,0.129 4.071,0.272 0.178,0.143 10 *B 1.455,0.701 1.455,0.202 1.455,0.202 1.539,0.202 false 5.817,0.13 5.996,0.274 0.178,0.143 10 *a 5.707,0.701 5.707,0.202 5.707,0.202 5.792,0.202 false
*A for LHD *B for RHD
*a Diagnostic Trouble Code (DTC) - -


NOTICE:

In sensor check mode, which is automatically entered after indicator check mode, troubleshooting may be partially performed. Be sure to perform the sensor check again.


HINT:

Refer to Diagnostic Trouble Code Chart for details of the codes.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DIAGNOSTIC TROUBLE CODE CHART

·

When there are no problems, DTC 00 is output.

·

As an example, the illustration shows that DTC 12 is output.




d.

If the DTCs are difficult to read because they change automatically, turn the "Driver TEMP" switch clockwise to display the DTCs one at a time so that they can be read easily. The DTCs change step by step each time the "Driver TEMP" switch is turned clockwise.

E228206
0.409,0.092 0.623,0.256 0.214,0.164 11 *A 3.892,0.093 4.106,0.257 0.214,0.164 11 *B
*A for LHD *B for RHD


HINT:

Press the "OFF" switch to finish panel diagnosis.



e.

Clear DTCs

i.

During the sensor check, press the "FRONT DEF" switch and "REAR DEF" switch simultaneously.

E228207
0.413,0.083 0.635,0.246 0.222,0.163 10 *A 3.893,0.082 4.115,0.245 0.222,0.163 10 *B
*A for LHD *B for RHD