Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2011.10–2013.07
RM19V0EQ _58 Vehicle Interior _014615 INTERIOR PANELS / TRIM _0074201 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


PROCEDURE

Hide 82171 1.INSTALL NO. 1 ROOF WIRE

a.

Apply double-sided tape as shown in the illustration.

B294906
4.094,0.698 4.094,1.083 false 4.969,0.948 4.969,1.229 false 4.969,1.083 5.167,1.083 5.167,1.083 5.167,0.417 false 2.229,0.583 2.479,0.583 false 0.438,1.417 0.885,1.677 0.448,0.26 12 false *A 0.438,4.219 0.969,4.531 0.531,0.313 12 false *B 1.198,0.677 1.396,0.875 0.198,0.198 10 false X 1.771,0.948 2.042,1.188 0.271,0.24 10 false Y 6.417,0.563 6.708,0.823 0.292,0.26 10 false Y 3.021,0.552 3.25,0.771 0.229,0.219 10 false Z 2.521,0.479 2.854,0.74 0.333,0.26 10 false *1 0.906,0.25 1.333,0.51 0.427,0.26 12 false *C 4.896,1.229 5.281,1.479 0.385,0.25 10 false *2 4.01,1.094 4.302,1.323 0.292,0.229 10 false *1
*A w/o Sliding Roof *B w/ Sliding Roof
*C Tape Attachment Locations (Reference) - -
*1 Double-sided Tape *2 Marking


Double-sided Tape Size:
X:

1 mm (0.0394 in.)

Y:

10 mm (0.394 in.)

Z:

20 mm (0.787 in.)



b.

Peel off the release paper from the double-sided tape.


c.

Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.


d.

Align the pink marking tape (A) on the No. 1 roof wire with the vehicle front side tab on the roof headlining.

B294905
1.479,2.469 1.615,2.188 false 4.906,1.01 5.042,0.948 false 3.427,0.51 3.552,0.542 false 2.906,0.292 3.188,0.438 false 3.51,3.531 3.365,3.604 false 5.563,0.729 5.24,0.885 false 5.813,3.927 5.958,3.854 false 6.375,3.656 6.115,3.792 false 1.49,5.26 1.625,4.969 false 3.969,3.219 3.688,3.458 false 3.885,1.208 4.01,1.135 false 4.458,0.948 4.198,1.083 false 3.927,4.677 4.052,4.604 false 4.479,4.406 4.219,4.542 false 3.573,0.479 3.927,0.708 0.354,0.229 10 false *3 4.76,0.958 5.031,1.167 0.271,0.208 10 false *4 2.76,0.198 3.073,0.458 0.313,0.26 10 false *5 1.385,2.49 1.74,2.75 0.354,0.26 10 false *1 0.292,0.198 0.76,0.469 0.469,0.271 12 false *A 0.292,2.917 0.698,3.208 0.406,0.292 12 false *B 5.958,1.729 6.323,2 0.365,0.271 10 false *6 3.219,3.542 3.552,3.833 0.333,0.292 10 false *3 5.573,0.656 5.885,0.854 0.313,0.198 10 false *5 5.667,3.865 5.958,4.083 0.292,0.219 10 false *4 6.396,3.552 6.708,3.781 0.313,0.229 10 false *5 1.396,5.271 1.74,5.531 0.344,0.26 10 false *1 5.969,4.479 6.344,4.719 0.375,0.24 10 false *6 3.99,3.094 4.375,3.427 0.385,0.333 10 false *5 3.74,1.146 4.042,1.385 0.302,0.24 10 false *2 4.469,0.844 4.854,1.063 0.385,0.219 10 false *5 3.771,4.604 4.063,4.854 0.292,0.25 10 false *2 4.5,4.302 4.854,4.583 0.354,0.281 10 false *5
*A w/o Sliding Roof *B w/ Sliding Roof
*1 Pink Marking Tape (A) *2 Pink Marking Tape (B)
*3 Pink Marking Tape (C) *4 Pink Marking Tape (D)
*5 Marking *6 Adjustment Area



e.

w/ Vanity Light:

i.

Turn the visor connector LH clockwise approximately 45° to install it to the roof headlining assembly.



f.

Align the edge of the pink marking tape (B) on the No. 1 roof wire with the markings on the roof headlining.


g.

Attach the No. 1 roof wire, starting from the pink marking tape (B) to the pink marking tape (A) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.




h.

w/ Vanity Light:

i.

Turn the visor connector RH clockwise approximately 45° to install it to the roof headlining assembly.


ii.

Attach the No. 1 roof wire, starting from the visor connector RH to the pink marking tape (B) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.




iii.

Attach the No. 1 roof wire, starting from the visor connector RH to the pink marking tape (B) while aligning it with the double-sided tape.



i.

Attach the No. 1 roof wire, starting from the pink marking tape (C) to the pink marking tape (B) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.




j.

Align the edge of the pink marking tape (D) on the No. 1 roof wire with the markings on the roof headlining.


k.

Attach the No. 1 roof wire, starting from the pink marking tape (A) to the pink marking tape (D) while aligning it with the double-sided tape.

NOTICE:
·

Securely attach the No. 1 roof wire.

·

If any of the No. 1 roof wire is left loose, this will cause abnormal noise. Make sure to attach the No. 1 roof wire without leaving any of it loose.



HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.



l.

Apply adhesive tape by aligning it with the markings on the roof headlining as shown in the illustration.

B294903
5,0.906 5.115,0.906 false 5,0.5 5.156,0.5 false 4.885,0.938 4.719,0.979 false 2.469,0.604 2.198,0.573 false 0.531,1.146 1,1.427 0.469,0.281 12 false *A 0.531,4.146 1.135,4.469 0.604,0.323 12 false *B 2.375,1.052 2.75,1.302 0.375,0.25 10 false X 3.177,0.646 3.51,0.948 0.333,0.302 10 false Y 5.188,0.385 5.521,0.646 0.333,0.26 10 false *2 5.135,0.802 5.521,1.094 0.385,0.292 10 false *2 0.323,6.458 0.667,6.719 0.344,0.26 10 false *1 4.542,0.885 4.927,1.104 0.385,0.219 10 false *1 2.021,0.469 2.385,0.75 0.365,0.281 10 false *1 1.615,0.094 2.094,0.385 0.479,0.292 12 false *C 1.563,1.635 1.99,1.896 0.427,0.26 12 false *D 1.563,3.365 2.073,3.667 0.51,0.302 12 false *E 1.563,5.073 2.042,5.396 0.479,0.323 12 false *F
*A w/o Sliding Roof *B w/ Sliding Roof
*C Tape Attachment Location (Reference) *D w/o EC Mirror
*E for LHD with EC Mirror *F for RHD with Rain Sensor
*1 Adhesive Tape *2 Marking


Adhesive Tape Size:
X:

20 mm (0.787 in.)

Y:

80 mm (3.15 in.)



Hide 86101J 2.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/o Digital Audio Broadcasting Antenna)

Hide 86101J 3.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/ Digital Audio Broadcasting Antenna)

Hide 63342 4.INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)

a.

Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the pad using hot-melt glue as shown in the illustration.

B294901
5.979,1.458 6.458,1.323 false 6.083,2.427 6.563,2.292 false 6.49,1.198 6.833,1.438 0.344,0.24 10 false *2 6.594,2.167 6.99,2.417 0.396,0.25 10 false *1
*1 Marking *2 Hot-melt Glue


NOTICE:

Securely attach the No. 2 roof silencer pad before the hot-melt glue cools.



Hide 63341 5.INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

a.

Align the markings on the roof headlining assembly with the 3 No. 1 roof silencer pads and install the pads using hot-melt glue as shown in the illustration.

B294899
5.906,1.438 6.385,1.302 false 5.979,2.406 6.458,2.271 false 6.417,1.198 6.802,1.417 0.385,0.219 10 false *2 6.479,2.156 6.833,2.448 0.354,0.292 10 false *1
*1 Marking *2 Hot-melt Glue


NOTICE:

Securely attach the No. 1 roof silencer pad before the hot-melt glue cools.



Hide 81340 6.INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)

a.

Install the vanity light assembly.

Click hereVehicle Interior>LIGHTING (INT)>VANITY LIGHT>INSTALLATION

HINT:

Use the same procedure for the other vanity light.