Home › Vehicle Interior › INTERIOR PANELS / TRIM › REAR SUNSHADE SYSTEM
RM19V0EQ _58 Vehicle Interior _014615 INTERIOR PANELS / TRIM _0074206 REAR SUNSHADE SYSTEM U

INTERIOR PANELS / TRIM  REAR SUNSHADE SYSTEM  TERMINALS OF ECU  


CHECK REAR SUNSHADE RELAY (REAR WINDOW SHADE ASSEMBLY)


B235131
3.458,0.271 3.813,0.479 0.354,0.208 3.51,0.292 3.917,0.656 0.406,0.365 10 false N19

a.

Disconnect the N19 rear sunshade relay (rear window shade assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
N19-7 (IG) - N19-1 (E) V - W-B IG power supply Ignition switch off Below 1 V
N19-7 (IG) - N19-1 (E) V - W-B IG power supply Ignition switch ON 11 to 14 V
N19-8 (B) - N19-1 (E) P - W-B Battery power supply Ignition switch off 11 to 14 V
N19-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the N19 rear sunshade relay (rear window shade assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
N19-3 (REV) - N19-1 (E) B - W-B Reverse signal Ignition switch ON, shift lever in any position other than R 11 to 14 V
N19-3 (REV) - N19-1 (E) B - W-B Reverse signal Ignition switch ON, shift lever in R Below 1 V
N19-5 (SW) - N19-1 (E) R - W-B Rear sunshade switch signal Ignition switch ON, rear sunshade switch not pushed 11 to 14 V
N19-5 (SW) - N19-1 (E) R - W-B Rear sunshade switch signal Ignition switch ON, rear sunshade switch pushed Below 1.5 V

If the result is not as specified, the rear sunshade relay (rear window shade assembly) may have a malfunction.



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Disconnect the I12 and MB junction block connectors.

B282096
2.188,3.771 2.51,3.979 0.323,0.208 5.5,5.021 5.823,5.229 0.323,0.208 3.865,5.01 4.188,5.219 0.323,0.208 1.083,5.01 1.406,5.219 0.323,0.208 1.74,6.292 2.063,6.5 0.323,0.208 4.885,6.292 5.208,6.5 0.323,0.208 3.375,7.531 3.698,7.74 0.323,0.208 4.646,3.771 4.969,3.979 0.323,0.208 6.052,5.021 6.375,5.229 0.323,0.208 4.042,1.135 4.042,0.854 4.042,0.854 4.156,0.854 false 1.813,1.76 2.073,1.76 false 1.813,2.094 2.073,2.094 false 1.271,2.771 1.531,2.771 false 4.219,0.781 4.708,1.094 0.49,0.313 10 false MB 3.438,7.552 3.927,7.875 0.49,0.323 10 false MB 5.583,5.042 5.927,5.25 0.344,0.208 10 false 3E 0.906,1.51 1.271,1.813 0.365,0.302 10 false 3C 1.177,5.021 1.563,5.313 0.385,0.292 10 false 3C 5.865,1.479 6.271,1.781 0.406,0.302 10 false 3B 1.823,6.313 2.25,6.615 0.427,0.302 10 false 3B 5.865,2.167 6.302,2.531 0.438,0.365 10 false 3A 4.969,6.313 5.365,6.615 0.396,0.302 10 false 3A 0.917,2.135 1.406,2.448 0.49,0.313 10 false 3D 3.948,5.031 4.396,5.354 0.448,0.323 10 false 3D 2.125,1.688 2.667,2.104 0.542,0.417 10 false I13 4.708,3.792 5.167,4.063 0.458,0.271 10 false I13 2.125,2.031 2.688,2.365 0.563,0.333 10 false I12 2.271,3.792 2.698,4.083 0.427,0.292 10 false I12 1.583,2.698 2.635,3.052 1.052,0.354 10 false 3E*A, 3F*B 5.854,5.042 6.26,5.333 0.406,0.292 10 false *A 6.135,5.042 6.5,5.313 0.365,0.271 10 false 3F 6.406,5.042 6.771,5.396 0.365,0.354 10 false *B
*A for LHD *B for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
I12-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
MB-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
MB-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground - IG power supply Ignition switch ON 11 to 14 V
MB-32 (IG) - Body ground - IG power supply Ignition switch off Below 1 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the I12 and MB junction block connectors.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
I13-15 (REV) - Body ground B - Body ground Reverse signal Ignition switch ON, shift lever in any position other than R 11 to 14 V
I13-15 (REV) - Body ground B - Body ground Reverse signal Ignition switch ON, shift lever in R Below 1 V

If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.