Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM19V0EQ _59 Vehicle Exterior _014616 WINDOW / GLASS _0074215 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


B164269
3.125,0.115 3.49,0.323 0.365,0.208 3.74,0.115 4.104,0.323 0.365,0.208 3.177,0.135 3.677,0.479 0.5,0.344 10 false K10 3.521,0.135 3.74,0.302 0.219,0.167 10 false *A 3.802,0.125 4.26,0.396 0.458,0.271 10 false J10 4.135,0.135 4.479,0.385 0.344,0.25 10 false *B
*A for LHD *B for RHD


a.

Disconnect the K10*1 or J10*2 power window regulator master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K10-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
K10-6 (B) - K10-1 (E) LG - W-B Power supply Ignition switch ON 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J10-9 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
J10-6 (B) - J10-9 (E) LG - W-B Power supply Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the K10*1 or J10*2 power window regulator master switch assembly.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K10-8*1 (U) - K10-1 (E)
K10-3*2 (U) - K10-1 (E)
L*1 - W-B
R*2 - W-B
Power window motor UP output Ignition switch ON, driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
K10-4*1 (A) - K10-1 (E) B - W-B Power window motor AUTO UP output Ignition switch ON, driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Power window motor AUTO DOWN output Ignition switch ON, driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open 11 to 14 V → Below 1 V → 11 to 14 V
K10-5*1 (D) - K10-1 (E)
K10-4*2 (D) - K10-1 (E)
V*1 - W-B
G*2 - W-B
Power window motor DOWN output Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
K10-16 (U) - K10-1 (E) W - W-B Power window motor UP output Ignition switch ON, front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
K10-15 (D) - K10-1 (E) R - W-B Power window motor DOWN output Ignition switch ON, front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
K10-12 (U) - K10-1 (E) L - W-B Power window motor UP output Ignition switch ON, rear LH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
K10-13 (D) - K10-1 (E) B - W-B Power window motor DOWN output Ignition switch ON, rear LH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
K10-10 (U) - K10-1 (E) Y - W-B Power window motor UP output Ignition switch ON, rear RH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
K10-18 (D) - K10-1 (E) LG - W-B Power window motor DOWN output Ignition switch ON, rear RH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

*1: w/ Jam Protection Function on Driver Door

*2: w/o Jam Protection Function on Driver Door


for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J10-1 (U) - J10-9 (E) BE - W-B Power window motor UP output Ignition switch ON, driver door power window switch OFF → UP (Manual operation) 11 to 14 V → Below 1 V
J10-4 (A) - J10-9 (E) B - W-B Power window motor AUTO UP output Ignition switch ON, driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed 11 to 14 V → Below 1 V → 11 to 14 V
Power window motor AUTO DOWN output Ignition switch ON, driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open 11 to 14 V → Below 1 V → 11 to 14 V
J10-5 (D) - J10-9 (E) V - W-B Power window motor DOWN output Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) 11 to 14 V → Below 1 V
J10-12 (U) - J10-9 (E) W - W-B Power window motor UP output Ignition switch ON, front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J10-13 (D) - J10-9 (E) R - W-B Power window motor DOWN output Ignition switch ON, front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
J10-18 (U) - J10-9 (E) L - W-B Power window motor UP output Ignition switch ON, rear LH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J10-10 (D) - J10-9 (E) V - W-B Power window motor DOWN output Ignition switch ON, rear LH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V
J10-16 (U) - J10-9 (E) Y - W-B Power window motor UP output Ignition switch ON, rear RH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J10-15 (D) - J10-9 (E) LG - W-B Power window motor DOWN output Ignition switch ON, rear RH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator master switch assembly may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Door)


B164270
3.125,0.146 3.49,0.354 0.365,0.208 3.729,0.146 4.094,0.354 0.365,0.208 3.198,0.167 3.635,0.448 0.438,0.281 10 false J11 3.781,0.167 4.208,0.448 0.427,0.281 10 false K11 3.51,0.177 3.729,0.344 0.219,0.167 10 false *A 4.115,0.167 4.333,0.333 0.219,0.167 10 false *B
*A for LHD *B for RHD


a.

Disconnect the J11*1 or K11*2 power window regulator switch assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J11-3 (B) - Body ground GR - Body ground Power supply Ignition switch ON 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K11-3 (B) - Body ground GR - Body ground Power supply Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J11*1 or K11*2 power window regulator switch assembly (for front passenger door).

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J11-4 (U) - Body ground G - Body ground Power window motor UP output Ignition switch ON, front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
J11-1 (D) - Body ground Y - Body ground Power window motor DOWN output Ignition switch ON, front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K11-4 (U) - Body ground G - Body ground Power window motor UP output Ignition switch ON, front passenger door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
K11-1 (D) - Body ground Y - Body ground Power window motor DOWN output Ignition switch ON, front passenger door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly (for front passenger door) may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH Door)


B164270
3.468,0.121 3.828,0.333 0.36,0.212 3.551,0.153 3.775,0.317 0.223,0.163 10 M6

a.

Disconnect the M6 power window regulator switch assembly (for rear LH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
M6-3 (B) - Body ground G - Body ground Power supply Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the M6 power window regulator switch assembly (for rear LH door).


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
M6-4 (U) - Body ground B - Body ground Power window motor UP output Ignition switch ON, rear LH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
M6-1 (D) - Body ground R - Body ground Power window motor DOWN output Ignition switch ON, rear LH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly (for rear LH door) may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Door)


B164270
3.509,0.094 3.869,0.306 0.36,0.212 3.606,0.127 3.805,0.29 0.199,0.163 10 L6

a.

Disconnect the L6 power window regulator switch assembly (for rear RH door) connector.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
L6-3 (B) - Body ground G - Body ground Power supply Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the L6 power window regulator switch assembly (for rear RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
L6-4 (U) - Body ground B - Body ground Power window motor UP output Ignition switch ON, rear RH door power window switch OFF → UP (Manual operation) Below 1 V → 11 to 14 V
L6-1 (D) - Body ground R - Body ground Power window motor DOWN output Ignition switch ON, rear RH door power window switch OFF → DOWN (Manual operation) Below 1 V → 11 to 14 V

If the result is not as specified, the power window regulator switch assembly (for rear RH door) may have a malfunction.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) (w/ Jam Protection Function on Driver Door)


B280976
2.104,0.469 2.5,0.708 0.396,0.24 2.115,0.948 2.51,1.188 0.396,0.24 2.229,0.51 2.677,0.865 0.448,0.354 10 false K9 2.552,0.51 2.833,0.833 0.281,0.323 10 false *A 2.552,1 2.885,1.24 0.333,0.24 10 false *B 2.229,0.99 2.594,1.292 0.365,0.302 10 false J9
*A for LHD *B for RHD


a.

Disconnect the K9*1 or J9*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K9-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
K9-2 (B) - Body ground W - Body ground Power supply Always 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J9-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
J9-2 (B) - Body ground W - Body ground Power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the K9*1 or J9*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K9-4 (AUTO) - K9-1 (E) B - W-B Power window motor AUTO UP input Ignition switch ON, driver door power window fully open 11 to 14 V
K9-4 (AUTO) - K9-1 (E) B - W-B Power window motor AUTO UP input Ignition switch ON, driver door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
K9-4 (AUTO) - K9-1 (E) B - W-B Power window motor AUTO UP input Ignition switch ON, driver door power window fully closed 11 to 14 V
K9-4 (AUTO) - K9-1 (E) B - W-B Power window motor AUTO DOWN input Ignition switch ON, driver door power window fully closed 11 to 14 V
K9-4 (AUTO) - K9-1 (E) B - W-B Power window motor AUTO DOWN input Ignition switch ON, driver door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
K9-4 (AUTO) - K9-1 (E) B - W-B Power window motor AUTO DOWN input Ignition switch ON, driver door power window fully open 11 to 14 V
K9-5 (LED) - K9-1 (E) Y - W-B LED illumination signal Ignition switch ON 11 to 14 V
K9-5 (LED) - K9-1 (E) Y - W-B LED illumination signal Approximately 43 seconds after ignition switch turned off Below 1 V
K9-7 (DWN1) - K9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
K9-7 (DWN1) - K9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
K9-7 (DWN1) - K9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window fully closed 11 to 14 V
K9-7 (DWN1) - K9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window regulator switch fully pushed down (Automatic position) Below 1 V
K9-7 (DWN1) - K9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window fully open 11 to 14 V
K9-10 (UP1) - K9-1 (E) L - W-B Power window motor UP input Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
K9-10 (UP1) - K9-1 (E) L - W-B Power window motor UP input Ignition switch ON, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V
K9-10 (UP1) - K9-1 (E) L - W-B Power window motor UP input Ignition switch ON, driver door power window fully open 11 to 14 V
K9-10 (UP1) - K9-1 (E) L - W-B Power window motor UP input Ignition switch ON, driver door power window regulator switch fully pulled up (Automatic operation) Below 1 V
K9-10 (UP1) - K9-1 (E) L - W-B Power window motor UP input Ignition switch ON, driver door power window fully closed 11 to 14 V

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO UP input Ignition switch ON, driver door power window fully open 11 to 14 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO UP input Ignition switch ON, driver door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) Below 1 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO UP input Ignition switch ON, driver door power window fully closed 11 to 14 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO DOWN input Ignition switch ON, driver door power window fully closed 11 to 14 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO DOWN input Ignition switch ON, driver door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) Below 1 V
J9-4 (AUTO) - J9-1 (E) B - W-B Power window motor AUTO DOWN input Ignition switch ON, driver door power window fully open 11 to 14 V
J9-5 (LED) - J9-1 (E) Y - W-B LED illumination signal Ignition switch ON 11 to 14 V
J9-5 (LED) - J9-1 (E) Y - W-B LED illumination signal Approximately 43 seconds after ignition switch turned off Below 1 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window fully closed 11 to 14 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window regulator switch fully pushed down (Automatic position) Below 1 V
J9-7 (DWN1) - J9-1 (E) V - W-B Power window motor DOWN input Ignition switch ON, driver door power window fully open 11 to 14 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Ignition switch ON, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Ignition switch ON, driver door power window fully open 11 to 14 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Ignition switch ON, driver door power window regulator switch fully pulled up (Automatic operation) Below 1 V
J9-10 (UP1) - J9-1 (E) BE - W-B Power window motor UP input Ignition switch ON, driver door power window fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor assembly (for driver door) may have a malfunction.



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Disconnect the MB and I12 main body ECU (multiplex network body ECU) connector.

B278841
2.302,3.771 2.625,3.979 0.323,0.208 5.625,5.01 5.948,5.219 0.323,0.208 6.26,2.094 6.583,2.302 0.323,0.208 2.01,1.865 2.333,2.073 0.323,0.208 2.01,1.521 2.333,1.729 0.323,0.208 0.313,2.063 0.635,2.271 0.323,0.208 0.24,2.51 0.563,2.719 0.323,0.208 0.24,2.75 0.563,2.958 0.323,0.208 0.313,1.438 0.635,1.646 0.323,0.208 6.25,1.49 6.573,1.698 0.323,0.208 3.979,5.031 4.302,5.24 0.323,0.208 1.198,5.01 1.521,5.219 0.323,0.208 1.854,6.292 2.177,6.5 0.323,0.208 5.021,6.292 5.344,6.5 0.323,0.208 3.5,7.531 3.823,7.74 0.323,0.208 4.76,3.771 5.083,3.979 0.323,0.208 6.146,5.01 6.469,5.219 0.323,0.208 4.281,0.75 4.604,0.958 0.323,0.208 4.156,1.135 4.156,0.854 4.156,0.854 4.271,0.854 false 6,1.594 6.25,1.594 false 6.01,2.198 6.26,2.198 false 1.625,1.969 2.01,1.969 false 1.635,1.615 2.01,1.615 false 0.635,2.167 0.969,2.167 false 0.802,2.771 1.115,2.771 false 0.635,1.531 0.969,1.531 false 1.729,0.958 1.958,0.688 1.958,0.688 2.167,0.688 false 1.469,1.698 1.563,1.698 false 1.469,2.146 1.563,2.146 false 1.469,3.198 1.469,1.688 false 3.552,7.542 4.052,7.979 0.5,0.438 10 false MB 5.708,5.021 6.031,5.281 0.323,0.26 10 false 3E 1.271,5.021 1.615,5.26 0.344,0.24 10 false 3C 1.938,6.302 2.375,6.594 0.438,0.292 10 false 3B 5.104,6.313 5.563,6.604 0.458,0.292 10 false 3A 4.052,5.042 4.448,5.302 0.396,0.26 10 false 3D 4.833,3.792 5.25,4.063 0.417,0.271 10 false I13 2.375,3.792 2.833,4.125 0.458,0.333 10 false I12 6.344,2.115 6.646,2.323 0.302,0.208 10 false 3A 2.083,1.885 2.521,2.177 0.438,0.292 10 false I12 2.083,1.542 2.594,1.875 0.51,0.333 10 false I13 0.396,2.083 0.792,2.365 0.396,0.281 10 false 3D 0.313,2.531 0.729,2.771 0.417,0.24 10 false 3E 0.625,2.542 0.844,2.74 0.219,0.198 10 false *B 0.313,2.771 0.74,3.063 0.427,0.292 10 false 3F 0.625,2.781 0.854,2.979 0.229,0.198 10 false *C 0.385,1.458 0.76,1.677 0.375,0.219 10 false 3C 6.323,1.51 6.625,1.76 0.302,0.25 10 false 3B 5.969,5.031 6.26,5.302 0.292,0.271 10 false *B 6.229,5.021 6.542,5.271 0.313,0.25 10 false 3F 6.5,5.031 6.854,5.313 0.354,0.281 10 false *C 4.333,0.771 4.792,1.042 0.458,0.271 10 false MB 0.396,0.177 0.646,0.385 0.25,0.208 10 false *A 1.521,3.198 1.771,3.406 0.25,0.208 10 false *2 2.219,0.615 2.469,0.823 0.25,0.208 10 false *1
*A Main body ECU (multiplex network body ECU) (2 Connector Type) *B for LHD
*C for RHD - -
*1 Main body ECU (multiplex network body ECU) *2 2 connectors


B282096
2.302,3.771 2.625,3.979 0.323,0.208 5.625,5.01 5.948,5.219 0.323,0.208 6.25,2.094 6.573,2.302 0.323,0.208 2.042,2.021 2.365,2.229 0.323,0.208 2.063,1.635 2.385,1.844 0.323,0.208 0.313,2.063 0.635,2.271 0.323,0.208 0.24,2.51 0.563,2.719 0.323,0.208 0.24,2.75 0.563,2.958 0.323,0.208 0.313,1.438 0.635,1.646 0.323,0.208 6.25,1.5 6.573,1.708 0.323,0.208 3.979,5.031 4.302,5.24 0.323,0.208 1.198,5.01 1.521,5.219 0.323,0.208 1.854,6.292 2.177,6.5 0.323,0.208 5.01,6.292 5.333,6.5 0.323,0.208 3.5,7.531 3.823,7.74 0.323,0.208 4.76,3.771 5.083,3.979 0.323,0.208 6.146,5.01 6.469,5.219 0.323,0.208 4.219,0.75 4.542,0.958 0.323,0.208 4.104,1.125 4.104,0.844 4.104,0.844 4.219,0.844 false 6,1.604 6.25,1.604 false 6,2.198 6.25,2.198 false 1.792,2.115 2.042,2.115 false 1.813,1.729 2.063,1.729 false 0.646,2.167 0.906,2.167 false 0.802,2.729 1.115,2.729 false 0.635,1.531 0.896,1.531 false 1.823,0.979 2.052,0.708 2.052,0.708 2.26,0.708 false 1.594,3.094 1.594,1.49 1.594,1.49 1.698,1.49 false 1.594,1.844 1.688,1.844 false 1.594,2.188 1.698,2.188 false 3.552,7.552 4.146,7.896 0.594,0.344 10 false MB 5.708,5.031 6.01,5.271 0.302,0.24 10 false 3E 1.271,5.031 1.792,5.385 0.521,0.354 10 false 3C 1.938,6.313 2.49,6.688 0.552,0.375 10 false 3B 5.083,6.313 5.552,6.625 0.469,0.313 10 false 3A 4.052,5.052 4.521,5.344 0.469,0.292 10 false 3D 4.833,3.802 5.365,4.167 0.531,0.365 10 false I13 2.375,3.802 2.948,4.208 0.573,0.406 10 false I12 6.333,2.115 6.625,2.313 0.292,0.198 10 false 3A 2.115,2.052 2.458,2.302 0.344,0.25 10 false I12 2.135,1.667 2.49,1.917 0.354,0.25 10 false I13 0.385,2.094 0.823,2.385 0.438,0.292 10 false 3D 0.313,2.542 0.635,2.833 0.323,0.292 10 false 3E 0.625,2.542 0.979,2.802 0.354,0.26 10 false *B 0.313,2.781 0.698,3.042 0.385,0.26 10 false 3F 0.625,2.802 1.063,3.115 0.438,0.313 10 false *C 0.385,1.469 0.896,1.792 0.51,0.323 10 false 3C 6.333,1.531 6.667,1.76 0.333,0.229 10 false 3B 5.969,5.042 6.229,5.271 0.26,0.229 10 false *B 6.229,5.031 6.583,5.26 0.354,0.229 10 false 3F 6.5,5.052 6.823,5.26 0.323,0.208 10 false *C 4.281,0.781 4.74,1.094 0.458,0.313 10 false MB 0.271,0.177 0.781,0.635 0.51,0.458 10 false *A 2.281,0.646 2.531,0.854 0.25,0.208 10 false *1 1.542,3.135 1.792,3.344 0.25,0.208 10 false *2
*A Main body ECU (multiplex network body ECU) (3 Connector Type) *B for LHD
*C for RHD - -
*1 Main body ECU (multiplex network body ECU) *2 3 connectors



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
I12-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
MB-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
MB-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
MB-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the MB and I12 main body ECU (multiplex network body ECU) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
3C-15 (FLCY) - Body ground L - Body ground Front door courtesy switch LH input Front door LH open Below 1 V
3C-15 (FLCY) - Body ground L - Body ground Front door courtesy switch LH input Front door LH closed Pulse generation
I13-19 (FRCY) - Body ground Y - Body ground Front door courtesy switch RH input Front door RH open Below 1 V
I13-19 (FRCY) - Body ground Y - Body ground Front door courtesy switch RH input Front door RH closed 11 to 14 V*4
Pulse generation*5
I13-11 (L2) - Body ground R - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
I13-11 (L2) - Body ground R - Body ground Driver door key-linked lock input Driver door key cylinder off 11 to 14 V*6
Pulse generation*7*8
I13-24 (UL3) - Body ground GR*2 - Body ground
Y*3 - Body ground
Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
I13-24 (UL3) - Body ground GR*2 - Body ground
Y*3 - Body ground
Driver door key-linked unlock input Driver door key cylinder off Pulse generation
I13-4 (PRG) - Body ground*1 P - Body ground Signal output to door control receiver Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder 11 to 14 V → Pulse generation → 11 to 14 V
I13-16 (RDA) - Body ground*1 L - Body ground Signal input from door control receiver Ignition switch off, all doors closed and transmitter switch not pressed 11 to 14 V
Ignition switch off, all doors closed and transmitter switch pressed Pulse generation

*1: w/o Smart Entry and Start System

*2: for LHD

*3: for RHD

*4: w/ Seat Position Memory System

*5: w/o Seat Position Memory System

*6: w/ Rear Sunshade System and w/o Seat Position Memory System

*7: w/o Rear Sunshade System

*8: w/ Rear Sunshade System and w/ Seat Position Memory System


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


a.

Disconnect the A43 certification ECU (smart key ECU assembly) connector.

B264892
1.947,0.596 2.327,0.847 0.381,0.251 2.009,0.645 2.285,0.815 0.277,0.17 10 A43 3.299,0.631 3.679,0.882 0.381,0.251 3.403,0.694 3.614,0.855 0.212,0.161 10 O1 4.882,0.631 5.262,0.882 0.381,0.251 4.986,0.694 5.198,0.862 0.212,0.168 10 I78


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
A43-2 (+B) - Body ground W - Body ground +B power supply Always 11 to 14 V
A43-11 (E) - Body ground W - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the A43 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
I78-5 (IG) - Body ground LG - Body ground IG power supply Ignition switch off Below 1 V
I78-5 (IG) - Body ground LG - Body ground IG power supply Ignition switch ON 11 to 14 V
O1-5 (RCO) - A43-11 (E) G - W-B Door control receiver power source
·

Ignition switch off

·

Transmitter switch not pressed


Below 1 V
O1-5 (RCO) - A43-11 (E) G - W-B Door control receiver power source
·

Ignition switch off

·

Lock or unlock transmitter switch pressed


4.5 to 5.5 V
O1-17 (RDAM) - A43-11 (E) Y - W-B Door control receiver data input signal Ignition switch off Pulse between 11 to 14 V occurs regularly

If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.