Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM19V0EQ _59 Vehicle Exterior _014616 WINDOW / GLASS _0074215 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor* or Main Body / Data List.

*: w/ Jam Protection Function on Driver Door



e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal ON or OFF ON: Driver door power window auto switch operated
OFF: Driver door power window auto switch not operated
-
D Door P/W Up SW Driver door power window manual up switch signal ON or OFF ON: Driver door power window manual up switch operated
OFF: Driver door power window manual up switch not operated
-
D Door P/W Down SW Driver door power window manual down switch signal ON or OFF ON: Driver door power window manual down switch operated
OFF: Driver door power window manual down switch not operated
-
Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position OK or Caution OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position OK or Caution OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position OK or Caution OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position OK or Caution OK: Normal manual up operation
Caution: Jam detected in the specified range
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
Number of Trouble Codes Number of trouble codes Min.: 0 or Max.: 255 Number of DTCs will be displayed -
Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver door lock/unlock switch lock signal (key-linked lock switch) ON or OFF ON: Driver door key cylinder turned to lock position
OFF: Driver door key cylinder turned to except lock position
-
D Door Key SW-UL Driver door lock/unlock switch unlock signal (key-linked unlock switch) ON or OFF ON: Driver door key cylinder turned to unlock position
OFF: Driver door key cylinder turned to except unlock position
-
FR Door Courtesy Front door courtesy light switch RH ON or OFF ON: Front door RH closed
OFF: Front door RH open
-
FL Door Courtesy Front door courtesy light switch LH ON or OFF ON: Front door LH closed
OFF: Front door LH open
-
Door Key P/W Up Door key linked power window up*1 ON or OFF Customization status displayed -
Door Key P/W Down Door key linked power window down*1 ON or OFF Customization status displayed -
P/W Down W/ Transmit Wireless transmitter linked power window down*1 ON or OFF Customization status displayed -
P/W Wireless Ope Buzz Buzzer sounds of wireless power window*1 ON or OFF Customization status displayed -
Communication D-Door Motor Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU)*2 OK or STOP OK: Normal communication
STOP: Communication stopped
-

*1: for RHD

*2: w/ Jam Protection Function on Driver Door




ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor* or Main Body / Active Test.

*: w/ Jam Protection Function on Driver Door



e.

Perform the Active Test according to the display on the intelligent tester.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
IG OFF P/W Control Permission Output Power window OFF / ON Perform this Active Test with the ignition switch off.