Use the same procedure for both the RH and LH sides.
The procedure described below is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
69284D
3.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.
4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
74260
5.REMOVE REAR ARMREST ASSEMBLY
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.
67604
6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
| *1 | Protective Tape |
Put protective tape around the rear door panel.
Remove the 3 screws.
Using a clip remover, disengage the 8 clips.
Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
| *1 | Reference Boss | *2 | Rear Door Inner Glass Weatherstrip |
Disengage the reference boss from the rear door panel.
Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
Disconnect the connector.
| *1 | Screwdriver |
Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
69206C
7.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the 2 claws and guide, and remove the rear door inside handle sub-assembly.
68174A
8.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
| *1 | Screwdriver |
Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
67842E
9.REMOVE REAR DOOR SERVICE HOLE COVER
Disconnect the connector and remove the rear door service hole cover.
Remove any remaining butyl tape from the door.
68640A
10.REMOVE REAR DOOR CHECK ASSEMBLY
Remove the bolt and 2 nuts and rear door check assembly.
67872
11.REMOVE REAR DOOR WEATHERSTRIP
Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.
68152C
12.REMOVE REAR DOOR GLASS RUN
Remove the rear door glass run.
67408F
13.REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY
Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.
When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.
68124B
14.REMOVE REAR DOOR QUARTER WINDOW GLASS
Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
68104
15.REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
Do not damage the door glass.
69906B
16.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY
| *1 | Protective Tape |
Using a screwdriver, remove the rear door glass channel sub-assembly.
Tape the screwdriver tip before use.
69975A
17.REMOVE REAR DOOR GLASS CHANNEL FILLER
Remove the rear door glass channel filler.
67674A
18.REMOVE REAR DOOR FRAME GARNISH
Disengage the clip and remove the rear door frame garnish.
This garnish needs to be replaced with a new one because the clip will break when removing it.
19.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY
| *1 | Temporary Bolt |
Disconnect the connector.
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.
Remove the 3 bolts.
Remove the rear door window regulator assembly.
Remove the temporary bolt from the rear door window regulator assembly.
85720E
20.REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY
Using a T25 "TORX" socket wrench, remove the 3 screws and rear power window regulator motor assembly.
69060A
21.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
| *1 | Release Plate |
Using a T30 "TORX" socket wrench, remove the 3 screws.
Move the rear door lock with motor assembly downward and pull the release plate out of the rear door outside handle frame.
When reusing the rear door lock with motor assembly:
Remove the door lock wiring harness seal from the rear door lock with motor assembly.
69740D
22.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
Using a screwdriver, disengage the claw.
Remove the rear door lock remote control cable assembly.
69780B
23.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY
Using a screwdriver, disengage the 3 claws.
Remove the rear door inside locking cable assembly.
69250G
24.REMOVE REAR DOOR OUTSIDE HANDLE COVER ASSEMBLY
Using a T30 "TORX" socket wrench, loosen the screw.
The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.
Disengage the claw and remove the rear door outside handle cover assembly.
69240
25.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY
Pull and hold the release plate of the rear door outside handle frame sub-assembly as shown in the illustration.
The release plate may interfere with the rear door outside handle assembly and may be damaged when removing the rear door outside handle assembly, unless the release plate of the rear door outside handle frame sub-assembly is pulled and held.
Remove the rear door outside handle assembly as shown in the illustration.
69241G
26.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD
Disengage the 3 claws and remove the rear door front outside handle pad.
69242G
27.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD
Disengage the 2 claws and remove the rear door rear outside handle pad.
69204A
28.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
| *1 | Door Handle Nut |
| *a | Outside |
| *b | Inside |
Using a T30 "TORX" socket wrench, remove the screw and door handle nut.
Slide the rear door outside handle frame sub-assembly to disengage the claw of the rear door outside handle frame sub-assembly, and then remove it.
67888F
29.REMOVE REAR DOOR NO. 2 WEATHERSTRIP
Using a clip remover, disengage the 5 clips and remove the rear door No. 2 weatherstrip.
67003C
30.REMOVE REAR DOOR PANEL CUSHION
Disengage the 2 claws and remove the 2 rear door panel cushions.
75740
31.REMOVE REAR DOOR BELT MOULDING ASSEMBLY
75762A
32.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING
75764A
33.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING
75988C
34.REMOVE REAR DOOR OUTSIDE STRIPE
75978H
35.REMOVE REAR DOOR LOWER OUTSIDE STRIPE