87910
1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Memory)
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Check the operation of the mirror surface.
Disconnect the outer rear view mirror assembly RH connector.
Apply battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1 (RMVR)
Battery negative (-) → Terminal 10 (RM+R) |
Turns upward |
| Battery positive (+) → Terminal 10 (RM+R)
Battery negative (-) → Terminal 1 (RMVR) |
Turns downward |
| Battery positive (+) → Terminal 9 (RMHR)
Battery negative (-) → Terminal 10 (RM+R) |
Turns left |
| Battery positive (+) → Terminal 10 (RM+R)
Battery negative (-) → Terminal 9 (RMHR) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly RH.
87940
2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Memory)
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Check the operation of the mirror surface.
Disconnect the outer rear view mirror assembly LH connector.
Apply battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1 (LMVR)
Battery negative (-) → Terminal 10 (LM+R) |
Turns upward |
| Battery positive (+) → Terminal 10 (LM+R)
Battery negative (-) → Terminal 1 (LMVR) |
Turns downward |
| Battery positive (+) → Terminal 9 (LMHR)
Battery negative (-) → Terminal 10 (LM+R) |
Turns left |
| Battery positive (+) → Terminal 10 (LM+R)
Battery negative (-) → Terminal 9 (LMHR) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly LH.
87910
3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Memory)
Check the operation of the mirror surface.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
Apply battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 4 (M+) |
Turns upward |
| Battery positive (+) → Terminal 4 (M+)
Battery negative (-) → Terminal 3 (MV) |
Turns downward |
| Battery positive (+) → Terminal 1 (MH)
Battery negative (-) → Terminal 4 (M+) |
Turns left |
| Battery positive (+) → Terminal 4 (M+)
Battery negative (-) → Terminal 1 (MH) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly RH.
87940
4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Memory)
Check the operation of the mirror surface.
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Apply battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 4 (M+) |
Turns upward |
| Battery positive (+) → Terminal 4 (M+)
Battery negative (-) → Terminal 3 (MV) |
Turns downward |
| Battery positive (+) → Terminal 1 (MH)
Battery negative (-) → Terminal 4 (M+) |
Turns left |
| Battery positive (+) → Terminal 4 (M+)
Battery negative (-) → Terminal 1 (MH) |
Turns right |
If the result is not as specified, replace the outer rear view mirror assembly LH.