Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM19V0EQ _59 Vehicle Exterior _014619 MIRROR (EXT) _0074236 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)

a.
B294031
1.417,4.222 1.645,4.373 0.227,0.151 10 M+ 1.734,0.842 1.734,0.29 1.734,0.29 1.906,0.29 false 1.933,2.31 2.084,2.461 0.151,0.151 10 *1 1.721,1.852 1.721,2.382 1.721,2.382 1.893,2.382 false 1.933,0.2 2.084,0.351 0.151,0.151 10 *2 1.975,3.772 1.975,4.303 1.975,4.303 1.713,4.303 false 2.147,3.772 2.147,4.423 2.147,4.423 2.512,4.423 false 2.336,3.772 2.336,4.131 2.336,4.131 2.508,4.131 false 2.56,4.33 2.681,4.481 0.121,0.151 10 E 2.56,4.038 2.944,4.189 0.384,0.151 10 MSW 0.524,2.757 0.675,2.908 0.151,0.151 10 *a
*1 Mirror Adjust Switch
*2 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the switch functions.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (M+) - 2 (E) Mirror adjust switch pressed up 90 to 110 Ω
Mirror adjust switch pressed down 437 to 503 Ω
Mirror adjust switch pressed left 744 to 856 Ω
Mirror adjust switch pressed right 225 to 275 Ω
Mirror adjust switch not pressed 10 kΩ or higher
1 (MSW) - 2 (E) Mirror select switch R Below 1 Ω
Mirror select switch L 90 to 110 Ω
Mirror select switch off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)

a.

w/o Retract mirror

i.

Check the mirror select switch and mirror surface adjust switch.


ii.
B254350
1.698,3.688 1.469,4.156 false 1.604,3.688 1.125,4.156 false 1.5,3.688 0.76,4.156 false 1.385,3.698 0.427,4.156 false 1.823,3.698 1.896,4.156 false 1.938,3.688 2.344,4.156 false 2.073,3.688 2.802,4.156 false 1.729,0.854 1.729,0.406 1.729,0.406 1.542,0.406 false 1.719,1.865 1.719,2.26 1.719,2.26 1.948,2.26 false 0.521,2.823 0.677,2.969 0.156,0.146 10 false *a 2.625,4.167 2.969,4.313 0.344,0.146 10 false MRH 2.167,4.167 2.5,4.313 0.333,0.146 10 false MRV 1.74,4.167 2.052,4.313 0.313,0.146 10 false MLV 1.281,4.167 1.594,4.313 0.313,0.146 10 false MLH 0.958,4.167 1.313,4.5 0.354,0.333 10 false M+ 0.656,4.167 0.771,4.313 0.115,0.146 10 false E 0.323,4.167 0.438,4.313 0.115,0.146 10 false B 1.333,0.323 1.5,0.479 0.167,0.156 10 false *1 1.99,2.167 2.156,2.323 0.167,0.156 10 false *2
*1 Mirror select switch
*2 Mirror surface adjust switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Switch Condition Specified Condition
4 (MLV) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
4 (MLV) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
5 (MLH) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
5 (MLH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher



iv.

Turn the mirror select switch to the R position.


v.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Switch Condition Specified Condition
3 (MRV) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
3 (MRV) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
2 (MRH) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
2 (MRH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.