Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM19V0EQ _59 Vehicle Exterior _014620 WIPER / WASHER _0074239 WIPER AND WASHER SYSTEM U

WIPER / WASHER  WIPER AND WASHER SYSTEM  TERMINALS OF ECU  


CHECK WINDSHIELD WIPER RELAY ASSEMBLY (w/ Auto Wiper System)


E125552
3.396,0.698 3.781,0.958 0.385,0.26 3.51,0.75 3.844,0.906 0.333,0.156 10 false I72

a.

Disconnect the I72 windshield wiper relay assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I72-2 (IG) - Body ground L - Body ground Ignition switch ON signal (Power source circuit) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
I72-8 (VR2) - I72-21 (VR1) B - W Adjusting volume circuit Windshield wiper switch adjusting ring* changed 0 to 220 Ω
I72-12 (E) - Body ground W-B - Body ground Body ground Always Below 1 Ω
I72-16 (WIG) - Body ground Y - Body ground Signal power source circuit Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
I72-25 (W) - Body ground GR - Body ground Front washer switch circuit Front washer switch on Below 1 Ω
Front washer switch off 10 kΩ or higher

HINT:

*: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.


If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the I72 windshield wiper relay assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I72-1 (+SM) - Body ground B - Body ground Front wiper motor position detection signal Front wiper motor in low or high operation Below 1 V ←→ 11 to 14 V
Front wiper motor off Below 1 V
I72-3 (C1) - I72-5 (CO) P - R Front wiper switch AUTO signal circuit Ignition switch ON, front wiper switch in AUTO Below 1 V
Ignition switch ON, front wiper switch off 11 to 14 V
I72-10 (+1) - Body ground B - Body ground Front wiper motor low speed signal circuit Front wiper motor in low operation 11 to 14 V
Front wiper motor off Below 1 V
I72-11 (+2) - Body ground V - Body ground Front wiper motor high speed signal circuit Front wiper motor in high operation 11 to 14 V
Front wiper motor off Below 1 V
I72-14 (MPX1) - Body ground G - Body ground Rain sensor signal Ignition switch ON Pulse generation
I72-24 (SPD) - Body ground V - Body ground Speed signal Ignition switch ON, wheel being rotated Pulse generation
(See Waveform 1)
I72-25 (W) - Body ground GR - Body ground Front washer switch circuit Front washer switch on Below 1 V
Front washer switch off 11 to 14 V

If the result is not as specified, the windshield wiper relay assembly may have a malfunction.

i.
I109926
2.844,1.25 3.302,1.448 0.458,0.198 10 false GND 0.938,1.479 1.323,1.677 0.385,0.198 10 false (A)

Waveform 1 (Reference):

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.