Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM19V0EQ _59 Vehicle Exterior _014620 WIPER / WASHER _0074242 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/o Auto Wiper System)

a.

for LHD:

i.
E171721
0.177,1.135 0.635,1.406 0.458,0.271 2.813,1.146 3.271,1.417 0.458,0.271 1.167,1.083 0.896,0.656 false 1.406,1.083 1.406,0.667 false 1.625,1.083 1.76,0.656 false 0.948,1.104 0.635,0.854 false 2.458,1.427 2.563,1.823 false 2.052,1.438 1.969,1.823 false 0.073,0.031 0.521,0.375 0.448,0.344 10 *a 0.313,1.177 0.74,1.458 0.427,0.281 10 I32 0.406,0.74 0.781,1.073 0.375,0.333 10 +2 0.75,0.479 1.094,0.729 0.344,0.25 10 +1 1.313,0.479 1.646,0.771 0.333,0.292 10 +B 1.677,0.479 2.021,0.802 0.344,0.323 10 +S 2.469,1.823 2.844,2.052 0.375,0.229 10 EW 1.833,1.833 2.24,2.094 0.406,0.26 10 WF 2.958,1.177 3.313,1.427 0.354,0.25 10 I31
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
I32-1 (+S) - I32-3 (+1) OFF Below 1 Ω
INT
I32-2 (+B) - I32-3 (+1) MIST
LO
I32-2 (+B) - I32-4 (+2) HI

Front Washer Switch
Tester Connection Switch Condition Specified Condition
I31-4 (EW) - I31-7 (WF) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



b.

for RHD:

i.
E226489
0.177,1.115 0.635,1.385 0.458,0.271 2.813,1.115 3.271,1.385 0.458,0.271 0.865,1.833 0.948,1.458 false 1.375,1.458 1.427,1.844 false 1.781,1.083 1.677,0.635 false 2.01,1.094 2.021,0.635 false 2.271,1.094 2.375,0.625 false 2.49,1.083 2.771,0.656 false 0.125,0.052 0.594,0.438 0.469,0.385 10 false *a 0.313,1.146 0.677,1.438 0.365,0.292 10 false I31 2.958,1.135 3.354,1.438 0.396,0.302 10 false I32 2.719,0.469 3.052,0.719 0.333,0.25 10 false +2 2.302,0.438 2.635,0.677 0.333,0.24 10 false +1 1.896,0.427 2.26,0.667 0.365,0.24 10 false +B 1.531,0.438 1.875,0.667 0.344,0.229 10 false +S 0.729,1.865 1.125,2.083 0.396,0.219 10 false EW 1.323,1.865 1.667,2.073 0.344,0.208 10 false WF
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
I32-4 (+S) - I32-2 (+1) OFF Below 1 Ω
INT
I32-3 (+B) - I32-2 (+1) MIST
LO
I32-3 (+B) - I32-1 (+2) HI

Front Washer Switch
Tester Connection Switch Condition Specified Condition
I31-7 (EW) - I31-4 (WF) ON Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/ Auto Wiper System)

a.
E227242
0.271,1.229 0.729,1.5 0.458,0.271 2.698,1.229 3.156,1.5 0.458,0.271 2.385,3.563 1.135,2.802 false 2.313,3.906 1.073,4.302 false 2.375,3.688 0.75,3.188 false 2.344,3.802 0.667,3.802 false 2.135,1.583 2.406,1.969 false 1.917,1.594 1.844,1.969 false 1.021,1.885 1.063,1.594 false 1.448,1.594 1.469,1.896 false 2.031,1.594 2.083,2.125 false 2.24,1.594 2.667,1.854 false 1.792,1.302 1.667,0.833 false 1.979,1.292 1.979,0.833 false 2.167,1.302 2.25,0.833 false 2.365,1.292 2.583,0.833 false 0.875,4.208 1.323,4.469 0.448,0.26 10 false P1 0.5,3.677 0.875,3.917 0.375,0.24 10 false P2 0.552,3.083 0.948,3.354 0.396,0.271 10 false P3 0.948,2.688 1.281,2.927 0.333,0.24 10 false P4 0.167,2.531 0.51,2.802 0.344,0.271 10 false *1 0.167,0.156 0.5,0.417 0.333,0.26 10 false *a 0.396,1.271 0.771,1.49 0.375,0.219 10 false I31 2.823,1.271 3.229,1.531 0.406,0.26 10 false I32 2.5,0.667 2.885,0.948 0.385,0.281 10 false +2 2.219,0.667 2.531,0.906 0.313,0.24 10 false +1 1.854,0.667 2.208,0.896 0.354,0.229 10 false +B 1.531,0.667 1.844,0.885 0.313,0.219 10 false +S 2.688,1.781 3.052,2.063 0.365,0.281 10 false E 2.302,1.979 2.792,2.229 0.49,0.25 10 false AUTO 0.885,1.906 1.208,2.073 0.323,0.167 10 false EW 1.365,1.906 1.688,2.156 0.323,0.25 10 false WF 1.969,2.146 2.406,2.406 0.438,0.26 10 false VR2 1.688,1.969 2.094,2.188 0.406,0.219 10 false VR1
*1 Windshield Wiper Switch Assembly (Adjusting Ring Position)
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
I32-2 (+1) - I32-4 (+S) OFF Below 1 Ω
I32-2 (+1) - I32-3 (+B) MIST
LO
I32-3 (+B) - I32-1 (+2) HI
I32-7 (AUTO) - I32-6 (E) AUTO

Front Washer Switch
Tester Connection Switch Condition Specified Condition
I31-7 (EW) - I31-4 (WF) ON Below 1 Ω
OFF 10 kΩ or higher

Adjusting Ring*
Tester Connection Switch Condition Specified Condition
I32-9 (VR1) - I32-8 (VR2) P1 209 to 231 Ω
P2 114 to 126 Ω
P3 58.9 to 65.1 Ω
P4 Below 1 Ω


HINT:

*: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.


If the result is not as specified, replace the windshield wiper switch assembly.