Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › 2011.10–2015.04
RM19V0EQ _59 Vehicle Exterior _014621 LIGHTING (EXT) _0074247 AUTOMATIC HIGH BEAM SYSTEM U

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / (desired system) / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: malfunction
Delay: standby mode
Aim Lmt: aiming misalignment
SAE Mod: SAE mode
Undefin: undefined state
LIN Err: LIN communication error
Auto H Beam STS1 Automatic high beam sensor state past 1 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: malfunction
Delay: standby mode
Aim Lmt: aiming misalignment
SAE Mod: SAE mode
Undefin: undefined state
LIN Err: LIN communication error
Auto H Beam STS2 Automatic high beam sensor state past 2 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: malfunction
Delay: standby mode
Aim Lmt: aiming misalignment
SAE Mod: SAE mode
Undefin: undefined state
LIN Err: LIN communication error
Auto H Beam STS3 Automatic high beam sensor state past 3 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: malfunction
Delay: standby mode
Aim Lmt: aiming misalignment
SAE Mod: SAE mode
Undefin: undefined state
LIN Err: LIN communication error
Auto H Beam STS4 Automatic high beam sensor state past 4 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: malfunction
Delay: standby mode
Aim Lmt: aiming misalignment
SAE Mod: SAE mode
Undefin: undefined state
LIN Err: LIN communication error
Auto H Beam STS5 Automatic high beam sensor state past 5 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: malfunction
Delay: standby mode
Aim Lmt: aiming misalignment
SAE Mod: SAE mode
Undefin: undefined state
LIN Err: LIN communication error
Auto H Beam STS6 Automatic high beam sensor state past 6 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: malfunction
Delay: standby mode
Aim Lmt: aiming misalignment
SAE Mod: SAE mode
Undefin: undefined state
LIN Err: LIN communication error
Auto H Beam STS7 Automatic high beam sensor state past 7 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed Undetec: undetected
CAM NA: camera detection malfunction
No sens: no detection
Hlight: oncoming vehicles with headlights on
Taillgt: preceding vehicles with taillights on
Speed: vehicle speed
Daytime: daytime state
Village: urban area
Malfunc: malfunction
Delay: standby mode
Aim Lmt: aiming misalignment
SAE Mod: SAE mode
Undefin: undefined state
LIN Err: LIN communication error
Body Electrical > AFS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Traveling Direction Traveling Direction Not Fwd or Fwd Not Fwd: Shift lever in R or N
Fwd: Shift lever in any position other than R or N
-
Engine Engine condition Run or Stop Run: Engine running
Stop: Engine stopped
-
+B IG power supply voltage value 0.00 to 19.75 V 11 to 14 V -
Steering Sens Signal Steering angle sensor signal value -384.0 deg to 382.5 deg Approx. 0 deg (When steering wheel is straight) Value changes according to steering wheel position
Steering Sens Center Pos Steering angle sensor center position -3072.0 deg to 3070.5 deg Condition can be displayed -
FR Wheel Speed Front right wheel speed 0.00 to 327.67 km/h (203.61 mph) Condition can be displayed -
FL Wheel Speed Front left wheel speed 0.00 to 327.67 km/h (203.61 mph) Condition can be displayed -
Vehicle Speed Vehicle speed 0.00 to 327.67 km/h (203.61 mph) Condition can be displayed -


ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / AFS / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > AFS > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Automatic High Beam Operation Automatic high beam system operation ON/OFF ON: Operation start
OFF: Operation stop