Home › Vehicle Exterior › LIGHTING (EXT) › FOG LIGHT ASSEMBLY › 2011.10–2015.04
RM19V0EQ _59 Vehicle Exterior _014621 LIGHTING (EXT) _0074251 FOG LIGHT ASSEMBLY N

LIGHTING (EXT)  FOG LIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:

It is possible that a bulb is incorrectly installed, affecting fog light aim. Bulb installation should be considered prior to performing the adjustment procedure.


PROCEDURE

Hide 1. PREPARE VEHICLE FOR FOG LIGHT AIM ADJUSTMENT

a.

Prepare the vehicle:

·

Ensure that there is no damage or deformation to the body around the fog lights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Sit a person of average weight (75 kg, 165 lb) in the driver's seat.



Hide 2. PREPARE FOR FOG LIGHT AIMING

a.
E225009
0.811,1.697 1.593,1.853 0.782,0.156 10 25 m or 3 m

Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 25 m (82 ft.) distance between the vehicle (fog light bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Position the front wheels straight ahead.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 25 m (82 ft.) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft.) to allow for checking and adjustment of fog light aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)




b.

Prepare a piece of thick white paper (approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

E225010
1.099,2.845 1.419,3.152 0.321,0.307 10 90° 4.527,2.862 4.847,3.169 0.321,0.307 10 90° 1.292,3.459 1.637,3.621 0.344,0.162 10 25 m 4.752,3.462 5.018,3.624 0.266,0.162 10 3 m 1.116,0.889 1.436,1.196 0.321,0.307 10 90° 4.549,0.893 4.869,1.2 0.321,0.307 10 90° 0.719,0.098 2.791,0.284 2.072,0.185 12 Alignment distance is 25 m: 4.154,0.098 6.138,0.284 1.984,0.185 12 Alignment distance is 3 m: 4.411,0.606 5.096,0.758 0.685,0.152 10 V RH Line 4.411,1.504 5.057,1.655 0.647,0.152 10 V LH Line 0.976,0.606 1.651,0.758 0.675,0.152 10 V RH Line 0.976,1.504 1.629,1.655 0.653,0.152 10 V LH Line 6.52,1.115 6.958,1.276 0.439,0.161 10 V Line 3.094,1.115 3.533,1.276 0.439,0.161 10 V Line 3.568,3.034 4.02,3.195 0.452,0.161 10 H Line 0.139,3.034 0.591,3.195 0.452,0.161 10 H Line

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
E257183C06
1.177,0.292 1.49,0.448 0.313,0.156 10 false *a 1.844,0.302 2.156,0.458 0.313,0.156 10 false *b 2.479,0.313 2.792,0.469 0.313,0.156 10 false *c 2.969,0.875 3.281,1.031 0.313,0.156 10 false *d 0.563,1.708 0.875,1.865 0.313,0.156 10 false *e
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground


Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

HINT:

Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb.


i.

H Line (Fog light height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.


ii.

V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):

Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the fog light bulbs).



Hide 3.INSPECT FOG LIGHT AIMING

a.

Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.


b.

Start the engine.


c.

Turn on the fog lights and check if the upper edge of the hot zone for each fog light matches the upper edge as shown in the illustration.

E168642
1.948,1.781 2.094,2.302 2.094,2.302 2.323,2.302 false 5.302,1.781 5.458,2.302 5.458,2.302 5.688,2.302 false 0.781,0.083 2.854,0.448 2.073,0.365 12 false Alignment distance is 25 m: 4.198,0.083 6.177,0.448 1.979,0.365 12 false Alignment distance is 3 m: 0.292,1.448 0.74,1.781 0.448,0.333 10 false H Line 3.667,1.448 4.115,1.771 0.448,0.323 10 false H Line 1.521,0.604 2.156,0.938 0.635,0.333 10 false V LH Line 2.667,1.927 3.188,2.302 0.521,0.375 10 false 376 mm 6.104,1.938 6.573,2.302 0.469,0.365 10 false 46 mm 4.854,0.958 5.51,1.292 0.656,0.333 10 false V RH Line 4.854,0.646 5.49,0.958 0.635,0.313 10 false V LH Line 1.521,0.938 2.177,1.271 0.656,0.333 10 false V RH Line 2.354,2.219 2.948,2.521 0.594,0.302 10 false Hot Zone 5.729,2.219 6.323,2.521 0.594,0.302 10 false Hot Zone

HINT:
·

If the alignment distance is 25 m (82 ft.):

The upper edge of the hot zone for the fog light should be 376 mm (1.24 ft.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The upper edge of the hot zone for the fog light should be 46 mm (1.78 in.) below the H line.




Hide 4.ADJUST FOG LIGHT AIMING

a.
E234038
2.659,2.756 2.813,2.909 0.154,0.153 10 *1 2.377,2.844 2.64,2.844 false
*1 Aiming Screw


Adjust the aim vertically:

Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.


HINT:

If it is not possible to correctly adjust fog light aim, check bulb, fog light unit and fog light unit reflector installation.