Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC LIGHT CONTROL SENSOR
RM19V0EQ _59 Vehicle Exterior _014621 LIGHTING (EXT) _0074261 AUTOMATIC LIGHT CONTROL SENSOR G

LIGHTING (EXT)  AUTOMATIC LIGHT CONTROL SENSOR  INSPECTION  


PROCEDURE

Hide 89120A 1.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

a.
E223976
0.083,0.06 0.305,0.253 0.222,0.193 10 *a 0.807,1.294 1.199,1.544 0.392,0.25 0.895,1.337 1.12,1.487 0.226,0.149 10 I61 2.286,1.592 2.659,1.741 0.373,0.149 10 CLTB 0.691,1.82 1.069,1.969 0.378,0.149 10 CLTE 1.91,1.675 2.261,1.675 false 1.56,1.503 1.107,1.821 false
*a Front view of wire harness connector
(to Automatic Light Control Sensor)


Disconnect the I61 automatic light control sensor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I61-6 (CLTB) - I61-3 (CLTE) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
I61-3 (CLTE) - Body ground Always Below 1 Ω


If the result is not as specified, there may be a malfunction on the wire harness side.


c.
E223977
0.155,0.11 0.357,0.266 0.203,0.156 10 *a 2.383,2.725 2.773,2.87 0.39,0.145 10 CLTS 2.535,2.376 2.921,2.52 0.385,0.145 10 CLTE 1.871,2.406 2.297,2.739 false 1.865,2.25 2.481,2.447 false 0.344,1.595 0.745,1.858 0.401,0.263 0.436,1.637 0.646,1.799 0.211,0.162 10 I61
*a Component with harness connected
(Automatic Light Control Sensor)


Reconnect the I61 automatic light control sensor connector.


d.

Connect an oscilloscope to the automatic light control sensor connector.


e.
E223978
2.953,1.027 3.297,1.187 0.344,0.16 10 GND 1.854,1.152 1.984,1.313 0.13,0.16 10 A

Check the waveform.

OK:
Tester Connection Tool Setting Switch Condition Specified Condition
I61-3 (CLTE) - I61-5 (CLTS) 5 V/DIV., 5 ms./DIV Ignition switch ON, light control switch in AUTO position Correct waveform is as shown


HINT:

If the ambient light becomes brighter, width A becomes narrower.


If the result is not as specified, the automatic light control sensor may have a malfunction.


Hide 89120A 2.INSPECT AUTOMATIC LIGHT CONTROL SENSOR (for Manual Air Conditioning System)

a.
E236973
0.17,0.172 0.372,0.328 0.203,0.156 10 *a 0.487,1.047 0.877,1.192 0.39,0.145 10 CLTB 2.556,1.227 2.941,1.372 0.385,0.145 10 CLTE 0.979,1.145 1.555,1.476 false 1.507,0.447 1.979,0.745 0.471,0.297 1.574,0.503 1.873,0.671 0.299,0.168 10 I159 1.913,1.66 2.49,1.329 false
*a Front view of wire harness connector
(to Automatic Light Control Sensor)


Disconnect the I159 automatic light control sensor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I159-3 (CLTB) - I159-5 (CLTE) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
I159-5 (CLTE) - Body ground Always Below 1 Ω


If the result is not as specified, there may be a malfunction on the wire harness side.


c.
E236974
0.174,0.147 0.377,0.303 0.203,0.156 10 *a 0.433,1.47 0.823,1.615 0.39,0.145 10 CLTS 0.422,2.448 0.807,2.593 0.385,0.145 10 CLTE 0.925,1.568 1.502,1.899 false 1.477,0.577 1.949,0.874 0.471,0.297 1.544,0.632 1.844,0.8 0.299,0.168 10 I159 0.914,2.497 1.49,2.166 false
*a Component with harness connected
(Automatic Light Control Sensor)


Reconnect the I159 automatic light control sensor connector.


d.

Connect an oscilloscope to the automatic light control sensor connector.


e.
E223978
2.953,1.027 3.297,1.187 0.344,0.16 10 GND 1.854,1.152 1.984,1.313 0.13,0.16 10 A

Check the waveform.

OK:
Tester Connection Tool Setting Switch Condition Specified Condition
I159-5 (CLTE) - I159-4 (CLTS) 5 V/DIV., 5 ms./DIV Ignition switch ON, light control switch in AUTO position Correct waveform is as shown


HINT:

If the ambient light becomes brighter, width A becomes narrower.


If the result is not as specified, the automatic light control sensor may have a malfunction.