Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2011.10–2014.05
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the ignition coil assembly (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the ignition coil assembly (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the ignition coil assembly (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the ignition coil assembly (No. 4 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A255924E06
4.427,1.385 4.375,0.938 4.375,0.938 4.302,0.938 false 5.333,1.156 5.563,0.719 5.563,0.719 5.635,0.719 false 3.896,0.844 4.5,1 0.604,0.156 10 Igniter 4.51,0.479 5.323,0.656 0.813,0.177 10 from Battery 5.688,0.646 7.073,1.198 1.385,0.552 10 Ignition Coil Assembly (No. 1 Cylinder) 5.615,1.854 6.729,2.031 1.115,0.177 10 No. 1 Spark Plug 5.615,3.063 6.729,3.24 1.115,0.177 10 No. 2 Spark Plug 5.615,4.385 6.729,4.563 1.115,0.177 10 No. 3 Spark Plug 5.615,5.688 6.729,5.865 1.115,0.177 10 No. 4 Spark Plug 2.74,5.927 3.083,6.104 0.344,0.177 10 ECM 2.896,1.448 3.26,1.604 0.365,0.156 10 IGT1 2.885,1.75 3.26,1.896 0.375,0.146 10 IGF1 0.302,1.5 2.031,1.667 1.729,0.167 10 Crankshaft Position Sensor 0.313,3.292 2.042,3.458 1.729,0.167 10 Camshaft Position Sensor 2.885,2.76 3.25,2.917 0.365,0.156 10 IGT2 2.896,5.406 3.26,5.563 0.365,0.156 10 IGT4 2.875,4.094 3.24,4.25 0.365,0.156 10 IGT3 0.188,4.49 2.146,5.313 1.958,0.823 10 Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, Throttle Position Sensor, etc.) 3.75,3.354 6.208,3.583 2.458,0.229 10 Ignition Coil Assembly (No. 2 Cylinder) 3.74,5.958 6.531,6.188 2.792,0.229 10 Ignition Coil Assembly (No. 4 Cylinder) 3.74,4.656 6.427,4.885 2.688,0.229 10 Ignition Coil Assembly (No. 3 Cylinder)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 Ignition coil assembly

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

No. 2 Ignition coil assembly

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 3 Ignition coil assembly

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

No. 4 Ignition coil assembly

·

ECM


Comes on DTC stored

A122717E38
3.021,0.958 3.385,1.156 0.365,0.198 10 GND 3.021,1.583 3.354,1.781 0.333,0.198 10 GND 0.24,0.375 0.615,0.875 0.375,0.5 10 CH1 (IGT) 0.219,1.406 0.635,1.76 0.417,0.354 10 CH2 (IGF1) 0.063,0.052 0.604,0.229 0.542,0.177 10 2 V/DIV. 1.354,1.896 2.104,2.042 0.75,0.146 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.

ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

A212405E23
1.802,1.677 2.198,1.854 0.396,0.177 10 ECM 2.99,1.302 3.26,1.49 0.271,0.188 10 IGT 2.979,1.729 3.26,1.885 0.281,0.156 10 IGF 4.156,1.51 4.594,1.656 0.438,0.146 10 Igniter 5.396,1.385 6.167,1.563 0.771,0.177 10 Ignition Coil 4.427,2.365 6.104,2.552 1.677,0.188 10 Ignition Coil Assembly 0.24,3.115 1.177,3.448 0.938,0.333 10 Ignition Signal (IGT) 1.677,3.573 2.167,3.76 0.49,0.188 10 Normal 1.417,3.969 2.188,4.156 0.771,0.188 10 Malfunction 0.052,3.875 1.365,4.344 1.313,0.469 10 Ignition Confirmation Signal (IGF1) 3.604,4.51 4.458,4.688 0.854,0.177 10 Circuit Open 5.948,4.969 6.313,5.167 0.365,0.198 10 Time

If the ECM does not receive any IGF1 signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0351, P0352, P0353 or P0354.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A266826E03
4.208,0.833 4.5,1 0.292,0.167 10 false IGN 0.667,2.802 1.156,2.958 0.49,0.156 10 false Battery 0.604,1.667 1.198,1.823 0.594,0.156 10 false FL MAIN 3.417,1.49 3.677,1.719 0.26,0.229 10 false IG2 2.458,0.979 2.625,1.167 0.167,0.188 10 false 2 4.865,0.531 5.031,0.719 0.167,0.188 10 false 1 2.448,0.521 2.615,0.708 0.167,0.188 10 false 3 4.865,0.99 5.031,1.177 0.167,0.188 10 false 8 1.438,0.833 2.083,1.063 0.646,0.229 10 false IG2-MAIN 4.802,2.521 5.156,2.677 0.354,0.156 10 false IG2D 5.229,2.427 5.427,2.615 0.198,0.188 10 false 9 6.448,0.698 6.646,0.885 0.198,0.188 10 false A 3.875,2.99 4.198,3.146 0.323,0.156 10 false A43 3.875,3.146 5.708,3.469 1.833,0.323 10 false Certification ECU (Smart Key ECU Assembly) 0.031,0.021 2.521,0.188 2.49,0.167 12 false w/ Smart Entry and Start System: 2.958,1.781 4.427,1.938 1.469,0.156 10 false No. 1 Integration Relay 2.396,0.698 2.615,0.875 0.219,0.177 10 false 1D 4.802,0.698 5.021,0.875 0.219,0.177 10 false 1A 4.802,1.156 5.021,1.333 0.219,0.177 10 false 1C 2.396,1.146 2.615,1.323 0.219,0.177 10 false 1E

A266827E06
4.208,0.844 4.5,1.01 0.292,0.167 10 false IGN 0.667,2.813 1.156,2.969 0.49,0.156 10 false Battery 0.573,2.042 1.146,2.198 0.573,0.156 10 false FL MAIN 3.406,1.5 3.667,1.729 0.26,0.229 10 false IG2 2.458,0.99 2.625,1.177 0.167,0.188 10 false 2 4.854,0.531 5.021,0.719 0.167,0.188 10 false 1 2.438,0.531 2.604,0.719 0.167,0.188 10 false 3 4.865,1 5.031,1.188 0.167,0.188 10 false 8 1.438,0.844 2.083,1.073 0.646,0.229 10 false IG2-MAIN 4.552,2.635 4.813,2.792 0.26,0.156 10 false IG2 4.865,2.427 5.01,2.615 0.146,0.188 10 false 6 6.438,0.698 6.635,0.885 0.198,0.188 10 false A 3.552,2.844 3.781,3 0.229,0.156 10 false I36 3.552,3 5.75,3.146 2.198,0.146 10 false Ignition or Starter Switch Assembly 0.021,0.031 2.594,0.198 2.573,0.167 12 false w/o Smart Entry and Start System: 2.969,1.792 4.448,1.938 1.479,0.146 10 false No. 1 Integration Relay 2.385,0.698 2.604,0.875 0.219,0.177 10 false 1D 4.802,0.688 5.021,0.865 0.219,0.177 10 false 1A 4.792,1.156 5.01,1.333 0.219,0.177 10 false 1C 2.385,1.146 2.604,1.323 0.219,0.177 10 false 1E 0.719,1.708 1.24,1.865 0.521,0.156 10 false ST/AM2 3.917,2.635 4.25,2.792 0.333,0.156 10 false AM2 3.75,2.427 3.896,2.615 0.146,0.188 10 false 5 4.896,2.677 5.927,2.844 1.031,0.167 10 false ECU-IG2 NO. 1

A255703E02
5.653,0.786 6.013,0.942 0.36,0.156 10 IGT1 5.653,2.177 6.013,2.334 0.36,0.156 10 IGT2 5.653,3.553 6.013,3.709 0.36,0.156 10 IGT3 5.653,4.961 6.013,5.117 0.36,0.156 10 IGT4 5.653,5.724 6.013,5.88 0.36,0.156 10 IGF1 5.837,6.215 6.114,6.389 0.277,0.175 10 E26 6.156,6.216 6.533,6.384 0.377,0.167 10 ECM 5.385,0.561 5.671,0.736 0.286,0.175 10 57 5.385,1.944 5.671,2.119 0.286,0.175 10 56 5.385,3.326 5.671,3.501 0.286,0.175 10 55 5.385,4.72 5.671,4.895 0.286,0.175 10 54 5.382,5.505 5.603,5.68 0.221,0.175 10 51 3.259,0.563 3.387,0.729 0.128,0.166 10 1 3.259,0.91 3.387,1.076 0.128,0.166 10 4 4.463,0.563 4.591,0.729 0.128,0.166 10 3 4.463,0.91 4.591,1.076 0.128,0.166 10 2 3.474,0.666 3.695,0.822 0.221,0.156 10 +B 4.055,0.666 4.391,0.836 0.337,0.17 10 IGT1 3.467,1.0 3.827,1.156 0.36,0.156 10 GND 4.108,1.0 4.384,1.165 0.277,0.166 10 IGF 2.82,1.404 3.088,1.56 0.269,0.156 10 E37 3.137,1.404 5.136,1.579 1.999,0.175 10 No. 1 Ignition Coil Assembly 3.259,1.964 3.387,2.13 0.128,0.166 10 1 3.259,2.311 3.387,2.477 0.128,0.166 10 4 4.463,1.964 4.591,2.13 0.128,0.166 10 3 4.463,2.311 4.591,2.477 0.128,0.166 10 2 3.474,2.067 3.695,2.223 0.221,0.156 10 +B 4.055,2.067 4.391,2.237 0.337,0.17 10 IGT2 3.467,2.401 3.827,2.557 0.36,0.156 10 GND 4.108,2.401 4.384,2.566 0.277,0.166 10 IGF 2.82,2.805 3.092,2.961 0.272,0.156 10 E40 3.137,2.805 5.145,2.98 2.008,0.175 10 No. 2 Ignition Coil Assembly 3.259,3.35 3.387,3.515 0.128,0.166 10 1 3.259,3.696 3.387,3.862 0.128,0.165 10 4 4.463,3.35 4.591,3.515 0.128,0.166 10 3 4.463,3.696 4.591,3.862 0.128,0.165 10 2 3.474,3.452 3.695,3.609 0.221,0.156 10 +B 4.055,3.452 4.391,3.623 0.337,0.17 10 IGT3 3.467,3.786 3.827,3.942 0.36,0.156 10 GND 4.108,3.786 4.384,3.951 0.277,0.166 10 IGF 2.82,4.19 3.106,4.346 0.286,0.156 10 E38 3.137,4.19 5.025,4.365 1.888,0.175 10 No. 3 Ignition Coil Assembly 3.259,4.739 3.387,4.904 0.128,0.166 10 1 3.259,5.085 3.387,5.251 0.128,0.166 10 4 4.463,4.739 4.591,4.904 0.128,0.166 10 3 4.463,5.085 4.591,5.251 0.128,0.166 10 2 3.474,4.841 3.695,4.998 0.221,0.156 10 +B 4.055,4.841 4.391,5.012 0.337,0.17 10 IGT4 3.467,5.175 3.827,5.331 0.36,0.156 10 GND 4.108,5.175 4.384,5.341 0.277,0.166 10 IGF 2.82,5.579 3.102,5.736 0.282,0.156 10 E43 3.137,5.579 4.96,5.754 1.823,0.175 10 No. 4 Ignition Coil Assembly 0.848,0.668 0.977,0.843 0.128,0.175 10 A

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E37-4 (GND) - Body ground Always Below 1 Ω
E40-4 (GND) - Body ground Always Below 1 Ω
E38-4 (GND) - Body ground Always Below 1 Ω
E43-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.
A194110C16
0.594,1.917 0.948,2.156 0.354,0.24 0.104,2.188 0.51,2.427 0.406,0.24 0.104,1.917 0.51,2.156 0.406,0.24 0.594,2.188 0.948,2.427 0.354,0.24 1.302,2.51 0.781,3.042 false 2.156,2.51 2.625,3.031 false 0.271,0.198 0.458,0.406 0.188,0.208 10 *a 0.646,3.063 0.854,3.24 0.208,0.177 10 +B 2.604,3.052 2.969,3.208 0.365,0.156 10 GND 0.198,1.948 0.49,2.135 0.292,0.188 10 E37 0.656,1.948 0.938,2.135 0.281,0.188 10 E40 0.198,2.229 0.469,2.417 0.271,0.188 10 E38 0.646,2.229 0.927,2.417 0.281,0.188 10 E43
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E37-1 (+B) - E37-4 (GND) Ignition switch ON 11 to 14 V
E40-1 (+B) - E40-4 (GND) Ignition switch ON 11 to 14 V
E38-1 (+B) - E38-4 (GND) Ignition switch ON 11 to 14 V
E43-1 (+B) - E43-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E37-2 (IGF) - E26-51 (IGF1) Always Below 1 Ω
E40-2 (IGF) - E26-51 (IGF1) Always Below 1 Ω
E38-2 (IGF) - E26-51 (IGF1) Always Below 1 Ω
E43-2 (IGF) - E26-51 (IGF1) Always Below 1 Ω
E37-3 (IGT1) - E26-57 (IGT1) Always Below 1 Ω
E40-3 (IGT2) - E26-56 (IGT2) Always Below 1 Ω
E38-3 (IGT3) - E26-55 (IGT3) Always Below 1 Ω
E43-3 (IGT4) - E26-54 (IGT4) Always Below 1 Ω
E37-3 (IGT1) or E26-57 (IGT1) - Body ground Always 10 kΩ or higher
E40-3 (IGT2) or E26-56 (IGT2) - Body ground Always 10 kΩ or higher
E38-3 (IGT3) or E26-55 (IGT3) - Body ground Always 10 kΩ or higher
E43-3 (IGT4) or E26-54 (IGT4) - Body ground Always 10 kΩ or higher
E37-2 (IGF), E40-2 (IGF), E38-2 (IGF), E43-2 (IGF) or E26-51 (IGF1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

B

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the ignition coil assembly connectors.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E37-1 (+B) - 1A-1 Always Below 1 Ω
E40-1 (+B) - 1A-1 Always Below 1 Ω
E38-1 (+B) - 1A-1 Always Below 1 Ω
E43-1 (+B) - 1A-1 Always Below 1 Ω
E37-1 (+B), E40-1 (+B), E38-1 (+B), E43-1 (+B) or 1A-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR