Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2011.10–2016.05
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P060E  Internal Control Module Throttle Position Performance  


MONITOR DESCRIPTION

The ECM monitors the signals received from the throttle position sensor No. 1 and stop light switch assembly. As the ECM monitors the STP signals of the stop light switch assembly and the throttle position sensor No. 1, if these signals do not correlate, the DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P060E Internal Control Module Throttle Position Performance Either of the following condition is met (1 trip detection logic):
·

There is an ECM main CPU error.

·

There is an ECM sub CPU error.


ECM Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the tester off.

5.

Turn the ignition switch off.

6.

Disconnect the tester.

7.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

8.

Connect the cable to the negative (-) battery terminal.

9.

Connect the tester to the DLC3.

10.

Turn the ignition switch to ON and turn the tester on.

11.

Wait 16 seconds or more.

12.

Enter the following menus: Powertrain / Engine and ECT / DTC.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P060E.

16.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P060E)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and turn the tester off.


f.

Disconnect the tester.


g.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


h.

Connect the cable to the negative (-) battery terminal.


i.

Connect the tester to the DLC3.


j.

Turn the ignition switch to ON.


k.

Turn the tester on.


l.

Wait 16 seconds or more.


m.

Enter the following menus: Powertrain / Engine and ECT / DTC.


n.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P060E is output B




A

B