The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stored the DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0420 | Catalyst System Efficiency Below Threshold (Bank 1) | The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic). | ·
Gas leak from exhaust system ·
Air fuel ratio sensor (sensor 1) ·
Heated oxygen sensor (sensor 2) ·
Exhaust manifold converter sub-assembly (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst) |
Comes on (Euro-OBD) / - (except Euro-OBD) | DTC stored (Euro-OBD) / - (except Euro-OBD) |
| *A | for Single Type | *B | for Dual Type |
| *1 | Air Fuel Ratio Sensor (Sensor 1) | *2 | Heated Oxygen Sensor (Sensor 2) |
| *3 | TWC: Front Catalyst | *4 | TWC: Rear Catalyst |
| *5 | Center Exhaust Pipe Assembly | *6 | Tail Exhaust Pipe Assembly RH |
| *7 | Tail Exhaust Pipe Assembly LH | *8 | Exhaust Manifold Converter Sub-assembly |
| *9 | Front Exhaust Pipe Assembly | - | - |
Replace the exhaust manifold converter sub-assembly (*8) and the front exhaust pipe assembly (*9) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor *1 and heated oxygen sensor *2)
| Required Sensors/Components (Main) | Air fuel ratio sensor
Heated oxygen sensor |
| Required Sensors/Components (Related) | Intake air temperature sensor
Mass air flow meter sub-assembly Crankshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Idling | Off |
| Engine speed | Less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or higher, and less than 80% |
| Shift position | 5th or higher |
| All of the following conditions are met | - |
| Mass air flow rate | 2.5 gm/sec or more, and less than 50 gm/sec |
| Front catalyst temperature (estimated) | 560°C (1040°F) or higher, and less than 840°C (1544°F) |
| Rear catalyst temperature (estimated) | 360°C (680°F) or higher, and less than 770°C (1418°F) |
Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Enter the following menus: Powertrain / Engine and ECT / DTC [C].
Read the pending DTCs.
If a pending DTC is output, system is malfunction.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0420.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].
Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Check the DTC judgment result again [E].
If the judgment result shows INCOMPLETE or N/A, drive the vehicle again under an increased load and than recheck the judgment result.
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.
(a) Connect the intelligent tester to the DLC3.
(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.
(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.
(d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the tester.
If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.
If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume for A/F Sensor Active Test using the tester.
If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
If any DTCs other than P0420 are output, troubleshoot those DTCs first.
A
B
Connect the intelligent tester to the DLC3.
Start the engine and warm it up.
Turn the tester on.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| AFS Voltage B1S1 |
| O2S B1S2 |
Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| Tester Display
(Sensor) |
Injection Volume | Status | Voltage |
|---|---|---|---|
| AFS Voltage B1S1
(Air fuel ratio) |
12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2
(Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status AFS Voltage B1S1 | Status O2S B1S2 | Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition | Misfire | Main Suspected Trouble Area | Proceed to |
|---|---|---|---|---|---|
| Lean/Rich | Lean/Rich | Normal | - | ·
Three-way catalytic converter ·
Gas leak from exhaust system |
A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - | ·
Air fuel ratio sensor |
B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - | ·
Air fuel ratio sensor |
|
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - | ·
Heated oxygen sensor ·
Gas leak from exhaust system |
C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - | ·
Heated oxygen sensor ·
Gas leak from exhaust system |
|
| Lean | Lean | Actual air fuel ratio lean | May occur | ·
Extremely lean actual air fuel ratio ·
Gas leak from exhaust system |
D |
| Rich | Rich | Actual air fuel ratio rich | - | ·
Extremely rich actual air fuel ratio ·
Gas leak from exhaust system |
Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.
Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.
Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.
Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST
A
B
C
D
Check for exhaust gas leaks.
No gas leaks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.
Confirm the replacement parts, referring to the illustration in the Catalyst Location.
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>COMPONENTS
Replace the front exhaust pipe assembly (TWC: Rear catalyst).
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace exhaust gas leak point.
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0420 is output | A |
| DTC is not output
(No pending DTCs output) |
B |
A
B
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.
Confirm the replacement parts, referring to the illustration in the Catalyst Location.
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>COMPONENTS
Replace the front exhaust pipe assembly (TWC: Rear catalyst).
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check for exhaust gas leaks.
No gas leaks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the heated oxygen sensor.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the exhaust gas leaks.
No gas leaks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0171
| Proceed to |
|---|
| NEXT |
NEXT