Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.



CHECK FREEZE FRAME DATA


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the blind spot monitor main switch (warning canceling switch assembly) on.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

f.

According to the display on the intelligent tester, select the trouble code data display with Freeze Frame Data.

Body Electrical > Blind Spot Monitor Master
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Warning Indicator Turning on(Master) State of the outer rear view mirror indicator RH turning on OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in right hand side warning area

·

Right turn signal: OFF

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Warning Indicator Flashing(Master) State of the outer rear view mirror indicator RH flashing OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in right hand side warning area

·

Right turn signal: ON

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Turn Switch State Master side, slave side state of the turn SW master ON, slave ON or OFF Master ON: Right turn switch on
Slave ON: Left turn switch on
OFF: Switch not operated
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
Body Electrical > Blind Spot Monitor Slave
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Warning Indicator Turning on(Slave) State of the outer rear view mirror indicator LH turning on OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in left hand side warning area

·

Left turn signal: OFF

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Warning Indicator Flashing(Slave) State of the outer rear view mirror indicator LH flashing OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in left hand side warning area

·

Vehicle speed 40 km/h (25 mph) or more

·

Left turn signal: ON

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Turn Switch State Master side, slave side state of the turn SW master ON, slave ON or OFF Master ON: Right turn switch on
Slave ON: Left turn switch on
OFF: Switch not operated
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -


CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the Freeze Frame Data


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the blind spot monitor main switch (warning canceling switch assembly) on.


d.

Turn the intelligent tester on.


e.

Clear the DTC and Freeze Frame Data.

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313
Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314