Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2011.10–2015.04
RM19V0EQ _56 Audio / Visual / Telematics _014601 PARK ASSIST / MONITORING _0074094 BLIND SPOT MONITOR SYSTEM U

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Blind spot monitor main switch (warning canceling switch assembly) OFF or ON ON: Blind spot monitor main switch (warning canceling switch assembly) on
OFF: Blind spot monitor main switch (warning canceling switch assembly) off
-
Warning Indicator Turning on(Master) State of the outer rear view mirror indicator RH turning on OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in right hand side warning area

·

Right turn signal: OFF

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Warning Indicator Flashing(Master) State of the outer rear view mirror indicator RH flashing OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in right hand side warning area

·

Right turn signal: ON

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Turn Switch State Master side, slave side state of the turn SW Master ON, Slave ON or OFF Master ON: Right turn switch on
Slave ON: Left turn switch on
OFF: Switch not operated
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
HV Flag Hybrid vehicle OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
Main SW Inspection Completeness Flag Completion of inspection for blind spot monitor main switch (warning canceling switch assembly) Incompl or compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when the blind spot monitor main switch (warning canceling switch assembly) is changed from off to on during Test Mode.
Beam Axis Inspection Completeness Flag Completion of beam axis inspection Incompl or compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Destination Undefined Flag Destination determination Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
when a malfunction is detected: More than 0
-
Body Electrical > Blind Spot Monitor Slave > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Warning Indicator Turning on(Slave) State of the outer rear view mirror indicator LH turning on OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in left hand side warning area

·

Left turn signal: OFF

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Warning Indicator Flashing(Slave) State of the outer rear view mirror indicator LH flashing OFF or ON OFF: The following conditions are not met

ON: All of the following conditions are met

·

Not during initial check

·

Vehicle detected in left hand side warning area

·

Vehicle speed 40 km/h (25 mph) or more

·

Left turn signal: ON

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated



-
Turn Switch State Master side, slave side state of the turn SW Master ON or Slave ON or OFF Master ON: Right turn switch on
Slave ON: Left turn switch on
OFF: Switch not operated
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
HV Flag Hybrid vehicle OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag VGRS installed OFF or ON OFF: VGRS not installed
ON: VGRS installed
-
Beam Axis Inspection Completeness Flag Completion of beam axis inspection Incompl or compl Incompl: Inspection not completed
Compl: Inspection completed
Changes to Compl when Test Mode has been entered.
Destination Undefined Flag Destination determination Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information
-
Number of DTC Number of DTC Min.: 0, Max.: 255 When system is normal: 0
when a malfunction is detected: More than 0
-