Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM19V0EQ _52 Drivetrain _014582 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0076198 AUTOMATIC TRANSAXLE SYSTEM D

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  INITIALIZATION  


RESET TRANSAXLE COMPENSATION CODE


NOTICE:
·

If the following parts have been replaced, initialize the ECM and perform the following "Reset Memory" and "Perform Road Test to Allow ECM to learn" steps.

- Valve body assembly

- Shift solenoid valve SL3

- Shift solenoid valve SL4

- ECM

·

The transaxle compensation code can only be initialize with the intelligent tester.



HINT:

The ECM memorizes the condition that the ECT controls the automatic transaxle assembly according to those characteristics. Therefore, when the automatic transaxle assembly, or ECM has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information. Reset procedure is as follows:


a.

Move the shift lever to N or P.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / A/T Code Reset.

Powertrain > Engine and ECT > Utility
Tester Display
A/T Code Registration
50005 234 204

g.

Press "Next" again to proceed.

NOTICE:

After the transaxle compensation code is initialized, perform the following "Reset Memory" and "Perform Road Test to Allow ECM to learn" steps.



h.

Press "Exit".



PERFORM ROAD TEST TO ALLOW ECM TO LEARN


NOTICE:

Perform the following procedure while strictly observing all traffic laws and speed limits.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position.

Powertrain > Engine and ECT > Data List
Tester Display
Throttle Sensor Position
50003 234 12

g.

From a standstill, achieve highest possible speed with the accelerator pedal opened 15% or less. Keep the accelerator pedal angle steady while driving the vehicle.

HINT:

"Throttle Sensor Position": 15% or less



h.

Repeat the previous step until shift shock no longer occurs.


i.

From a standstill, achieve highest possible speed with the accelerator pedal opened 25% to 35%. Keep the accelerator pedal angle steady while driving the vehicle.

HINT:

"Throttle Sensor Position": 25% to 35%



j.

Repeat the previous step until shift shock no longer occurs.



RESET MEMORY


NOTICE:

Reset Memory can be performed only with the intelligent tester.


HINT:

The ECM (ECT) memorizes the vehicle conditions when controlling the automatic transaxle assembly and engine assembly.

Therefore, when the automatic transaxle assembly, valve body assembly, shift solenoid valve SL3, shift solenoid valve SL4, or ECM has been replaced, it is necessary to reset the memory so that the ECM can memorize the new information.


a.

Reset procedure is as follows.

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the intelligent tester on.


v.

Enter the following menus: "Powertrain / Engine and ECT / Utility / Reset Memory". Then, press "Next".

NOTICE:

After performing Reset Memory, be sure to perform "Perform Road Test to Allow ECM to Learn" described earlier.


Powertrain > Engine and ECT > Utility
Tester Display
Reset Memory
50005 234 176